2017 MAZDA MODEL CX-3 Owners Manual (in English)

4–9
When Driving
Start/Stop Engine
NOTE
The push button start indicator light
(green) will À ash even if the push button
start is pressed before depressing
the brake pedal. If the brake pedal is
depressed under this condition, the engine
can be started by resuming the procedure
following this.

3. Touch the push button start using the
backside of the key (as shown) while
the push button start indicator light
(green) À ashes.


Push button start
TransmitterIndicator light
N O T E
When touching the push button start using
the backside of the key as shown in the
illustration, touch the push button start
with the lock switch side of the key facing
up.

4. Verify that the push button start
indicator light (green) turns on.
5. Press the push button start to start the
engine.
N O T E
 


y The engine cannot be started unless the
brake pedal is fully depressed.
 


y If there is a malfunction with the push
button start function, the push button
start indicator light (amber) À ashes.
In this case, the engine may start,
however, have the vehicle checked at an
Authorized Mazda Dealer as soon as
possible.
 


y If the push button start indicator light
(green) does not illuminate, perform the
operation from the beginning again. If
it does not illuminate, have the vehicle
checked at an Authorized Mazda Dealer.
 


y To switch the ignition position without
starting the engine, perform the
following operations after the push
button start indicator light (green) turns
on.

1. Release the brake pedal.
2. Press the push button start to switch
the ignition position. The ignition
switches in the order of ACC, ON,
and off each time the push button
start is pressed. To switch the
ignition position again, perform the
operation from the beginning.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–10
When Driving
Start/Stop Engine
Emergency Operation for Starting
the Engine
If the KEY warning light (red) illuminates,
or the push button start indicator light
(amber) À ashes, this could indicate that
the engine may not start using the usual
starting method. Have your vehicle
inspected at an Authorized Mazda Dealer
as soon as possible. If this occurs, the
engine can be force-started. Press and hold
the push button start until the engine starts.
Other procedures necessary for starting
the engine such as having the key in the
cabin, and depressing the brake pedal are
required.
Turning the Engine Off
WARNING
Do not stop the engine while the vehicle
is moving:
Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking, which
could cause an accident and serious
injury.

1. Stop the vehicle completely.
2. Shift the selector lever to the P position
and set the parking brake.
3. Press the push button start to turn off
the engine. The ignition position is off.

CAUTION
When leaving the vehicle, make sure
the push button start is off .

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–11
When Driving
Start/Stop Engine
N O T E
 


y The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
 


y When the push button start is pressed
from ON to ACC or OFF, the KEY
indicator light (green) may À ash for
approximately 30 seconds indicating
that the remaining battery power of the
key is low.
  Replace with a new battery before the
key becomes unusable.
  Refer to Key Battery Replacement on
page 6-39 .
 


y If the engine is turned off while the
selector lever is in a position other than
P, the ignition switches to ACC.

Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–12
When Driving
Instrument Cluster and Display
M e t e r s a n d G a u g e s


Type A
Type B
Type C
Steering Switch (Digital Speedometer Type)
(Analog Speedometer Type (With Tachometer))
(Analog Speedometer Type (Without Tachometer))
Instrument Cluster

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–13
When Driving
Instrument Cluster and Display



Speedometer .......................................................................................................... page 4-14



Odometer, Trip Meter and Trip Meter Selector .................................................... page 4-14



Tachometer ............................................................................................................ page 4-18



Fuel Gauge ............................................................................................................ page 4-18



Dashboard Illumination......................................................................................... page 4-19



Outside Temperature Display ................................................................................ page 4-19



Cruise Control Set Vehicle Speed Display ............................................................ page 4-20



Active Driving Display ......................................................................................... page 4-22



Trip Computer and INFO Switch .......................................................................... page 4-20



Speed Unit Selector ............................................................................................... page 4-14



Odometer, Trip Meter, Trip Computer and Trip Meter Selector ........................... page 4-16
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–14
When Driving
Instrument Cluster and Display
*Some models.
Speedometer
The speedometer indicates the speed of the
vehicle.
N O T E
(Analog speedometer type)
If a few seconds have elapsed after
switching the ignition off, the needle may
deviate. However, this does not indicate a
problem.

Speed Unit Selector (Digital
Speedometer)
In some countries, you may have to
change the speed units between km/h and
mph.
Press the speed unit selector for 1.5
seconds or more.
The speed units for the speedometer will
change between km/h and mph.


Speedometer
Speed unit selector

Odometer, Trip Meter and Trip
Meter Selector *
The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.


Press the selector Press the selector
Press the selector Odometer
Trip meter A
Trip meter BSelector


N O T E
When the ignition is switched to ACC or
off, the odometer or trip meters cannot be
displayed, however, pressing the selector
can inadvertently switch the trip meters or
reset them during an approximate ten-
minute period in the following cases:
 


y After the ignition is switched to off from
ON.
 


y After the driver's door is opened.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–15
When Driving
Instrument Cluster and Display
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.

For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is ¿ lled.

When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption. N O T E
 


y (Vehicles with type B audio) 
 If the fuel economy data is reset using
the fuel economy monitor, or trip A
is reset using the trip meter when the
function which synchronizes the fuel
economy monitor and the trip meter is
on, the fuel economy data and trip A are
reset simultaneously.
  Refer to Fuel Economy Monitor on page
4-62 .
 


y Only the trip meters record tenths of
kilometers (miles).
 


y The trip record will be erased when: 



y The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


y The vehicle is driven over 9999.9 km
(mile).


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–16
When Driving
Instrument Cluster and Display
*Some models.
Odometer, Trip Meter, Trip
Computer and Trip Meter
Selector
*
T h e d i s p l a y m o d e c a n b e c h a n g e d
between trip meter A and trip meter B by
pressing the selector while one of them
is displayed. The selected mode will be
displayed.

Selector
Current fuel economy modeDistance-to-empty modeTrip meter B
Trip meter AOdometer

N O T E
When the ignition is switched to ACC or
off, the odometer or trip meters cannot be
displayed, however, pressing the selector
can inadvertently switch the trip meters or
reset them during an approximate ten-
minute period in the following cases:
 


y After the ignition is switched to off from
ON.
 


y After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is ¿ lled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
The trip meter records the total distance
the vehicle is driven until the meter is
again reset. Return it to “0.0” by holding
the selector depressed for 1 second
or more. Use this meter to measure
trip distances and to compute fuel
consumption.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD