2017 INFINITI QX30 sensor

Unlocking doors
1. Carry the Intelligent Key.
2. Touch the inner surface of the door handle.
3. All doors and the lift gate will unlock.
4. The turn signals flash once.
CHANGING THE SETTINGS OF THE
LOCKING SYSTEM
You can change the settings of the locking
system. This means that only the driver’s door
and the fuel-filler lid are unlocked when the
vehicle is unlocked. This is useful if you fre-
quently travel alone.
To change the setting:simultaneously press the
andbuttons for approximately 6
seconds.
NOTE
If the setting of the locking system is changed
within the signal range of the vehicle, pressing
the
andbutton will lock or unlock
the vehicle. The key now functions as follows:
To unlock the driver’s door:
press the
button once.
To unlock centrally:press the
button
twice.
To lock centrally: press the
button.
The Intelligent key function is changed as fol-
lows:
To unlock the driver’s door: touch the inner
surface of the door handle on the driver’s door.
To unlock centrally: touch the inner surface of
the door handle on the front passenger door or
the rear door.
To lock centrally: touch the outer sensor surface
on one of the door handles
To restore the factory settings: simultaneously
press the
andbutton for approxi-
mately 6 seconds.
Pre-driving checks and adjustments3-11

NOTE
When the monitor displays the front view and
the steering wheel turns about 90 degrees or
less from the neutral position, both the right and
left predicted course lines
6are displayed.
When the steering wheel turns about 90 degrees
or more, a line is displayed only on the opposite
side of the turn.
Bird’s-eye view
:
WARNING
•Objects in the bird’s-eye view will appear
farther than the actual distance.
•Tall objects, such as a curb or a vehicle, may
be misaligned or not displayed at the seam
of the views.
•Objects that are above the camera cannot
be displayed.
•The view for the bird’s-eye view may be mis-
aligned when the camera position alters.
•A line on the ground may be misaligned and
is not seen as being straight at the seam of
the views. The misalignment will increase
as the line proceeds away from the vehicle.
•Tire angle display does not indicate the ac-
tual tire angle. The bird’s-eye view shows the overhead view of
the vehicle, which helps confirm the vehicle
position.
The vehicle icon
1shows the position of the
vehicle.
NOTE
The size of the vehicle icon on the bird’s-eye
view may differ somewhat from the actual ve-
hicle.
The areas that the cameras cannot cover
2are
indicated in black.
The non-viewable area
2is highlighted in
yellow for several seconds after the bird’s-eye
view is displayed. It will be shown only the first
time after the ignition switch is placed in the ON
position. When the corner of the vehicle moves closer to
an object, the corner sensor indicator
3ap-
pears.
NAA1681
Display screen, heater and air conditioner, and audio system4-27

Front-side view:
Guiding lines that indicate the approximate
width and the front end of the vehicle are
displayed on the monitor.
The front-of-vehicle line
1shows the front part
of the vehicle.
The side-of-vehicle line
2shows the approxi-
mate vehicle width including the outside mir-
rors.
The extensions
3of both the front1and side
2lines are shown with a green dotted line.
The corner sensor indicator
4will appear
when a corner of the vehicle moves closer to an
object.
DIFFERENCE BETWEEN PREDICTED AND
ACTUAL DISTANCES
The displayed guidelines and their locations on
the ground are for approximate reference only.
Objects on uphill or downhill surfaces or pro-
jecting objects will be actually located at dis-
tances different from those displayed in the
monitor relative to the guidelines (refer to illus-
trations). When in doubt, turn around and view
the objects as you are backing up, or park and
exit the vehicle to view the positioning of
objects behind the vehicle.
Backing up on a steep uphill
When backing up the vehicle up a hill, the
distance guide lines and the vehicle width
guide lines are shown closer than the actual
distance. Note that any object on the hill is
viewed in the monitor farther than it appears.
SAA1842ZLeft-Hand Drive (LHD) models*
NAA1675
4-28Display screen, heater and air conditioner, and audio system

2. Touch [Camera/Sonar]
3. Touch [Sonar]
[Sonar sensitivity]:
Adjust the sonar sensor sensitivity level by
touching [+]/[-].
[Sonar volume]:
Adjust the buzzer volume by touching [+]/[-].
AAround View Monitor display
BINFINITI controller
C

•The MOD system is not a substitute for
proper vehicle operation and is not de-
signed to prevent contact with objects sur-
rounding the vehicle. When maneuvering,
always use the outside mirror and rearview
mirror and turn and check the surroundings
to ensure it is safe to maneuver.
•The system is deactivated at speeds above 5
MPH (8 km/h). It is reactivated at lower
speeds.
•The MOD system is not designed to detect
the surrounding stationary objects.
The Moving Object Detection (MOD) system can
inform the driver of moving objects surrounding
the vehicle when driving out of garages, maneu-
vering into parking lots and in other such
instances.
The MOD system detects moving objects by
using image processing technology on the im-
age shown on the display.
MOD SYSTEM OPERATION
The MOD system will activate automatically
under the following conditions:
•When the shift lever is in the R (Reverse)
position.
•When the button is pressed to
switch from a different screen to the camera
view on the display.
•When vehicle speed decreases below ap-
proximately 5 MPH (8 km/h).
•When the ignition switch is placed in the OFF
position and then back to the ON position.
NOTE
•The MOD system does not detect moving
objects in the front-side view. The MOD icon
is not displayed on the screen when in this
view.
•While the parking sensor warning tone is
sounding, the MOD system does not chime. The MOD system operates in the following
conditions when the camera view is displayed:
When the shift lever is in the R (Reverse)
position and the vehicle speed is approximately
5 MPH (8 km/h ) or less, the MOD system
detects moving objects in the camera view. The
MOD system will not operate if the lift gate is
open.
When the MOD system detects moving objects
near the vehicle, a chime will be heard and a
yellow frame
1will be displayed on the moni-
tor.
While the MOD system continues to detect
moving objects, the yellow frame continues to
be displayed.
The yellow frame
1is displayed on each view
in the rear view modes.
NAA1781Bird’s-eye view
4-38Display screen, heater and air conditioner, and audio system

Setting itemResult
[Navigation]* Display the Navigation setting screen.
Refer to the Navigation Owner’s Manual for details.
[Audio] Display the Audio settings screen.
SeeAudio settings earlier in this section
[Screen] Set the screen display to the preferred settings.
SeeScreen settings earlier in this section
[Volume Adjustment] Set the volume for each item.
SeeVolume settings earlier in this section
[Clock] Set the Clock to your preferred settings.
SeeClock settings earlier in this section
[InTouch Services] Set INFINITI InTouch
TMServices.
Refer to the Navigation Owner’s Manual for details.
[Voice recognition] Set Minimize Voice Feedback to on/off and the audio setting for voice recognition use.
[Camera/Sonar] Set the camera and parking sensor (sonar) to the preferred settings. SeeAround View Monitor setting earlier in this section
[Other] [Language] Set the language to the preferred settings.
SeeLanguage settings earlier in this section
[Keyboard Type] Set the Keyboard Type to [QWERTY] or [ABC].
[Low on Fuel Alert] Set the fuel low notification to on/off.
[Software information] Display the software information.
* : Models with navigation system.
NOTE
•The displayed items vary depending on the vehicle model and equipped options.
•The order of displayed items can be sorted.
Display screen, heater and air conditioner, and audio system4-121

MONITOR SYSTEM
SymptomPossible cause Possible solution
The image on the display is not clear. The front of the camera lens is dirty.Gently wipe off the dirt with a damp soft cloth.
Moisture drops such as rain or snow form on the camera lens. Gently wipe off the drops with a soft cloth.
Light such as sunlight or a headlight beam from another vehicle directly enters the camera. This is not a malfunction. It will return to normal
when the light disappears.
Moisture condensation occurs in the camera lens due to rapid temperature change. This is not a malfunction. It will return to normal after
driving for short period of time.
Objects on the display may not be clear in a dark place or at night. Adjust the brightness or the contrast settings of the
screen.
The image on the display flickers. The vehicle is under fluorescent light. This is not a malfunction.
The colors of the object on the display look different from those of the actual object. This is a typical phenomenon for cameras.
This is not a malfunction.
Image does not appear on the display. The shift lever is not shifted to the R (Reverse)
position. Shift the shift lever to the R (Reverse) position.
[Automatic Display with Sonar] is OFF. Set [Automatic Display with Sonar] to ON.
The image appears on the display from the wrong angle. The lift gate is open.
Close the lift gate.
The image on the display is not clearly visible. Strong light or reflected light enters the camera. This is not a malfunction.
The sensor is not detective. There is ice or snow on the sensor. Flush out ice and snow with warm water.
There is dirt, mud or wax on the sensor. Gently wipe off the dirt with a damp soft cloth.
Vertical lines appear on the image. Strong reflected light from the bumper enters the
camera. This is not a malfunction.
4-134Display screen, heater and air conditioner, and audio system

Intelligent Cruise Control (ICC) system (Full speed range)
(if equipped).........................5-47
ICC system operation ..................5-48
ICC switch (cruise control lever) ...........5-49
ICC system display and indicators ..........5-49
Operating ICC ...................... .5-50
ICC Limitations ..................... .5-54
Tips for driving with the ICC system .........5-56
System temporarily unavailable ............5-59
System maintenance ..................5-60
Forward emergency braking (FEB) system (if
equipped) .......................... .5-60
FEB system operation ..................5-61
Turning the FEB system on/off ............5-64
FEB system limitations .................5-65
System temporarily unavailable ............5-65
System maintenance ..................5-66
FCC Notice ....................... .5-67
Active sound enhancement ................5-67
Active sound enhancement ..............5-68
Intelligent Parking Assist (IPA) (if equipped) ......5-68
Important safety notes .................5-68
Detecting parking spaces ...............5-69
Parking ..........................5-70
Exiting a parking space .................5-71
Canceling IPA ...................... .5-73Parking sensor system (if equipped)
...........5-73
Parking sensor overview ................5-75
Range of the sensors ..................5-79
Parking sensor system OFF switch ..........5-79
Parking sensor function settings ...........5-80
Problems with parking sensor system ........5-81
Break-in schedule ..................... .5-81
Fuel efficient driving tips ..................5-82
Increasing fuel economy ..................5-83
Four-Wheel Drive (4WD) (if equipped) ..........5-83
Parking ........................... .5-84
Switching off

the engine ................5-86
Extended parking ................... .5-86
Electric power steering system ..............5-86
Brake system .........................5-87
Brake precautions ................... .5-87
Anti-lock Braking System (ABS) ............5-88
Vehicle Dynamic Control (VDC) system .........5-90
Traction Control System (TCS) .............5-91
Characteristics of VDC ..................5-91
EBD (electronic brake force distribution) ......5-92
Steer Control ...................... .5-92
Hill Start Assist (HSA) ................... .5-93