2017 INFINITI QX30 sensor

button turns off. Airflow and air distribution
are set to automatic mode.
or
•Air-conditioning system or automatic climate
control: adjust the temperature control (see
Heater and air conditionerin the4. Display
screen, heater and air conditioner, and audio
system section).
HEADLIGHT SWITCH
1Left-hand parking lights
2Right-hand parking lights
3Side lights and license plate light-
ing
4 Automatic headlight mode, con-
trolled by the light sensor
5Low beam/high beam headlights
6Rear fog light
7Front fog lights (if equipped)
8Headlight aiming control (halogen head-
lights only)
INFINITI recommends that you consult the local
regulations concerning the use of lights. If you hear a warning tone when you leave the
vehicle, the side lights may still be switched on.
Turn the light switch to
.
The exterior lighting (except the side lights/
parking lights) switches off automatically if you:
•Remove the key from the ignition switch (if
equipped).
•Open the driver’s door with the ignition
switch in the OFF position.
CAUTION
Use the headlights with the engine running to
avoid discharging the vehicle battery.
NIC2619LED headlightsNIC2697Halogen headlights
HEADLIGHT AND TURN SIGNAL SWITCHES
Instruments and controls2-63

Automatic headlight mode
is the preferred light switch setting. The
light setting is automatically selected according
to the brightness of the ambient light (excep-
tion: poor visibility due to weather conditions
such as fog, snow or spray):
•Ignition switch in ACC or ON position: the
side lights are switched on or off automati-
cally depending on the brightness of the
ambient light.
•With the engine running: if you have
switched on the daytime driving lights func-
tion in the vehicle information display, the
side lights and low beam headlights are
switched on or off automatically depending
on the brightness of the ambient light.
To switch on automatic headlight mode: turn the
light switch to .
WARNING
When the light switch is set to , the
low-beam headlights may not be switched on
automatically if there is fog, snow or other
causes of poor visibility due to the weather
conditions such as spray. There is a risk of an
accident
In such situations, turn the light switch to
. The automatic headlight feature is only an aid.
The driver is responsible for the vehicle lighting
at all times.
The daytime driving lights improve the detect-
ability of your vehicle during the day.
WARNING
When the daytime running light system is ac-
tive, tail lights on your vehicle are not on. It is
necessary at dusk to turn on your headlights.
Failure to do so could cause an accident injur-
ing yourself and others.
When the side lights and low-beam headlights
are switched on, the green
(side lights)
and(low-beam headlights) indicator
lights in the combination meter light up.
Low-beam headlights
When the ignition is switched on and the light
switch is in theposition, the side lights
and low-beam headlights are switched on even
if the light sensor does not sense dark ambient
light conditions. This is advantageous when
there is fog or rain.
To switch on the low-beam headlights:
•Switch the ignition switch to the ON position,
or start the engine.
•Turn the light switch to. The greenindicator light in the combination me-
ter lights up.
Side lights
NOTE
Always park your vehicle safely and sufficiently
lit according to legal standards. To reduce the
chance of a discharged vehicle battery, avoid the
continuous use of the
sidelights or park-
ing lights for several hours.
To switch on: turn the light switch to
. The
greenindicator light in the combination
meter lights up.
Parking lights
Switching on the parking lights ensures that the
corresponding side of the vehicle is illuminated.
To switch on the parking lights:
•The key is not in the ignition switch or the
switch is in the OFF position.
•Turn the light switch to(left-hand side
of the vehicle) or(right-hand side of
the vehicle).
2-64Instruments and controls

HIGH BEAM ASSIST (LED HEADLIGHT
ONLY)
You can use this function to set the headlights
to change between low beam and high beam
automatically. The system recognizes vehicles
with their lights on, either approaching from the
opposite direction or traveling in front of your
vehicle, and consequently switches the head-
lights from high beam to low beam.
The system automatically adapts the low beam
headlight range depending on the distance to
the other vehicle. Once the system no longer
detects any other vehicles, it switches on the
high beam headlights again.
The system’s optical sensor is located behind
the windshield near the overhead control panel.
WARNING
•The high beam assist system is a conve-
nience but is not a substitute for safe driv-
ing operation. The driver should remain
alert at all times, ensure safe driving prac-
tices and switch the high beams and low
beam manually when necessary.
•The high beam or low beam may not switch
automatically under the following condi-
tions. Switch the high beam and low beam
manually.– During bad weather (rain, fog, snow,
wind, etc.).
– When a light source similar to a head-
light or tail light is in the vicinity of the
vehicle.
– When the headlights of the oncoming
vehicle or the leading vehicle are turned
off, when the color of the light is affected
due to foreign materials on the lights, or
when the light beam is out of position.
– When there is a sudden, continuous
change in brightness.
– When driving on a road that passes over
rolling hills, or a road that has level dif-
ferences.
– When driving on a road with many
curves. –
When a sign or mirror-like surface is re-
flecting intense light towards the front of
the vehicle.
– When the container, etc. being towed by
a leading vehicle is reflecting intense
light.
– When a headlight on your vehicle is dam-
aged or dirty.
– When the vehicle is leaning at an angle
due to a punctured tire, being towed, etc.
•The timing of switching the low beam and
high beam may change under the following
situations.
– The brightness of the headlights of the
oncoming vehicle or leading vehicle.
– The movement and direction of the on-
coming vehicle and the leading vehicle.
– When only one light on the oncoming
vehicle or the leading vehicle is illumi-
nated.
– When the oncoming vehicle or the lead-
ing vehicle is a two-wheeled vehicle.
– Road conditions (incline, curve, the road
surface, etc.).
– The number of passengers and the
amount of luggage.
•High beam Assist does not recognize road
users:
– Who have no lights, e.g. pedestrians.
NDS595
Instruments and controls2-67

–Who have low intensity lighting, e. g.
cyclists.
– Whose lighting is blocked, e.g. by a bar-
rier.
•In very rare cases, High beam Assist recog-
nizes road users too late or not at all. In this,
or in similar situations, the automatic high
beam headlights will not be deactivated or
activated regardless. There is a risk of an
accident.
•Always carefully observe the traffic condi-
tions and switch off the high beam head-
lights in good time.
CAUTION
High beam Assist cannot compensate for road
and weather circumstances while driving. The
system saves the driver from having to operate
the switch. The driver always remains respon-
sible for choosing the correct light setting.
Specific situations in which to operate the
headlight switch manually:
•In heavy rain, snowy conditions. (general
poor visibility and bad weather conditions).
•When the vehicle sensors are dirty, covered
or broken.
Switching High Beam Assist on/off
To switch on:
Turn the light switch to and press the
combination switch beyond the pressure point
in the direction of arrow
3. Theindicator
light in the vehicle information display lights up
when it is dark and the light sensor switches on
the low-beam headlights.
If you are driving at speeds above approxi-
mately 28 MPH (45 km/h) the headlight range is
set automatically depending on the distance
between the vehicle and other road users.
If you are driving at speeds above approxi-
mately 34 MPH (55 km/h) and no other road
users are detected, the high beam headlights
are switched on automatically. The
indi- cator light in the combination meter also lights
up.
If you are driving at speeds below approxi-
mately 28 MPH (45 km/h) or other road users
are detected or the roads are adequately lit The
high beam headlights are switched off auto-
matically. The
indicator light in the com-
bination meter goes out. Theindicator
light in the vehicle information display remains
lit.
To deactivate
:
Move the combination switch back to its normal
position Theindicator light in the vehicle
information display goes out.
HEADLIGHTS MISTED UP ON THE
INSIDE
Certain climatic and physical conditions may
cause moisture to form in the headlight. This
moisture does not affect the functionality of the
headlight.
NIC2618
2-68Instruments and controls

INSTRUMENT BRIGHTNESS CONTROL
The light sensor in the combination meter au-
tomatically controls the brightness of the in-
strument panel
In daylight, the displays in the combination
meter are not illuminated
The lighting in the combination meter, displays
and controls in the vehicle interior can be
adjusted using the brightness control knob.
The brightness control knob
1is located be-
hind the steering wheel.
Turn the brightness control knob clockwise or
counterclockwise. If the light switch is set to
orthe brightness is dependent
upon the brightness of the ambient light.
FRONT FOG LIGHTS
In conditions where visibility is poor due to fog,
snow or rain, the fog lights improve visibility as
well as making it easier for other road users to
see you. They can be operated together with the
side lights or together with the side lights and
low beam headlights.
To switch on the fog lights:
•Turn the ignition switch to the ON position or
start the engine.
•Turn the light switch toor .
•Press thebutton. The greenindicator light in the combination meter
lights up To switch off the front fog lights:
•press thebutton The greenindica-
tor light in the combination meter turns off.
Only vehicles with front fog lights are equipped
with the “Fog lights” function.
REAR FOG LIGHT
The rear fog light improves the visibility of your
vehicle in heavy fog for the following traffic.
Please observe the country-specific laws on the
use of rear fog lights.
NOTE
The front fog lights must be switched on before
the rear fog light will operate.
To switch on the rear fog light:
•Turn the ignition switch to the ON position or
start the engine.
•Turn the light switch toor .
•Press thebutton. The yellowindicator light in the combination meter
lights up
To switch off the rear fog light:
•press thebutton The yellowindicator light in the combination meter
turns off.
NIC2615NIC2699
FOG LIGHT SWITCH (IF SO EQUIPPED)
Instruments and controls2-69

Press and hold thebutton until the side
windows are in the desired position.
To interrupt convenience opening: release the
button.
Convenience closing feature
WARNING
When the convenience closing feature is oper-
ating, parts of the body could become trapped
in the closing area of the side window. There is
a risk of injury. Observe the complete closing
procedure when the convenience closing fea-
ture is operating. When closing make sure that
no parts of the body are in the closing area.
For vehicles with Intelligent key: The key can
also be used to carry out the following functions
simultaneously:
•Lock the vehicle
•Close the side windows The driver’s door and the door at which the
handle is used must both be closed. The key
must be outside the vehicle. The gap between
the key and the corresponding door handle
should not be greater than 1 m.
Press and hold the
button until the side
windows are fully closed.
To interrupt convenience closing: release the
button.
You can also use the keyless locking feature to
activate convenience closing: Touch recessed sensor surface
1on the door
handle until the side windows are fully closed.
NOTE
Make sure you only touch recessed sensor sur-
face
1.
To interrupt convenience opening: release the
recessed sensor surface
1on the door handle.
Resetting the side windows
If a side window can no longer be closed fully,
you must reset it.
1. Switch the ignition switch to the ON position.
2. Close the door.
3. Pull the corresponding switch on the door control panel until the side window is com-
pletely closed
NPA1478
2-74Instruments and controls

To unlock the vehicle:touch the inner surface of
the door handle.
To lock the vehicle: touch sensor surface
1.or
2.
Make sure that you do not touch the inner
surface of the door handle.
Convenience closing feature: touch recessed
sensor surface
1for an extended period. (See
Convenience closing feature in the
2. Instruments and controls section).To unlock the lift gate: press the lift gate switch
1.
When unlocking, the turn signals flash once
When locking, they flash three times.
NOTE
When the locator lighting is activated, it lights
up when it is dark after the vehicle is unlocked
with the intelligent key (see separate operating
instructions).
You can also set an audible signal to con firm
that the vehicle has been locked. The audible
signal can be activated or deactivated using the
on-board computer (see Activating/
deactivating the acoustic locking confirmation
in the 2. Instruments and controls section)LOCKING WITH THE MECHANICAL KEY
The driver’s door can be locked/unlocked from
outside using the mechanical key if the battery
is dead.
To lock the door, insert the mechanical key into
the driver’s door key cylinder and turn it to-
wards the front of the vehicle
1.
To unlock the door, turn the key towards the
rear of the vehicle
2.
See Mechanical key earlier in this section for
instructions on accessing the Intelligent Key
system mechanical key.
NOTE
The alarm system will be triggered when the
door is opened using the mechanical key (alarm
equipped models). To stop the alarm, turn the
NPA1489NPA1479SPA2602Z
Pre-driving checks and adjustments3-5

DOOR LOCKS/UNLOCKS PRECAUTION
•Do not touch the door handle request switch
with the Intelligent Key held in your hand as
illustrated. The close distance to the door
handle will cause the Intelligent Key system
to have difficulty recognizing that the Intelli-
gent Key is outside the vehicle.
•To prevent the Intelligent Key from being left
inside the vehicle, make sure you carry the
Intelligent Key
INFINITI INTELLIGENT KEY OPERATION
You can lock or unlock the doors without taking
the Intelligent Key out of your pocket or bag.
When you carry the Intelligent Key with you, you
can lock or unlock all doors by pushing the door
handle request switch within the range of op-
eration.
Locking doors
1. Push the P (Park) button to engage the P(Park) position, place the ignition switch in
the LOCK position and make sure you carry
the Intelligent Key with you.
2. Close all doors.
3. Touch any sensor surface
1or2.
4. All doors and the lift gate will lock. 5. The turn signals flash three times.
NOTE
•Doors do not lock by pushing the door
handle request switch while any door is
open. However, doors lock with the mechani-
cal key even if any door is open.
•The driver’s door and the door at which the
handle is used, must both be closed.
•The doors may not lock when the Intelligent
Key is in the same hand that is operating the
request switch to lock the door. Put the
Intelligent Key in a purse, pocket or your
other hand.
CAUTION
•When locking the doors using the request
switch, make sure to have the Intelligent
Key in your possession before operating the
request switch to prevent the Intelligent
Key from being left in the vehicle.
•The request switch is operational only when
the Intelligent Key has been detected by the
Intelligent Key system.
WPD0375ZNPA1489
3-10Pre-driving checks and adjustments