2016 SUBARU WRX Owners Manual

Instruments and controls/Multi function display
! Auto light sensor sensitivity setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.
2. Operate the “ ” or “ ” switch to
select the “ Auto Light Sensor ” item. Then push the
button.
3. The current setting will be displayed.
Push the
button to enter the selection
mode.
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then push the button.
5. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
button.
6. The system will notify you that the
setting is complete.3-88

If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.
! Keyless access setting (models
with “ keyless access with push-
button start system ” )
! Preparation for keyless access
settings
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83. 2. Operate the “ ” or “ ” switch to
select the “ Keyless Access Setting ” item.
Then push the
button.
! Driver ’ s door unlock setting
1. Perform the preparation steps accord-
ing to “ Preparation for keyless access
settings ” F 3-89. 2. Operate the “ ” or “ ” switch to
select the “ Driver ’ s Door Unlock ” item.
Then push the
button.
3. The current setting will be displayed.
Push the
button to enter the selection
mode.Instruments and controls/Multi function display
– CONTINUED –3-89

Instruments and controls/Multi function display
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then push the
button.
5. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
button. 6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again. ! Welcome lighting setting
The leaving time and approaching time
settings can be adjusted.
! Leaving time setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.
2. Operate the “ ” or “ ” switch to
select the “ Welcome Lighting ” item, and
then push the
switch.3-90

3. Select the “ Leaving time set ” by
operating the “
” or “ ” switch, and then
push the
switch.
4. The current setting will be displayed.
Push the
switch to enter the selection
mode. 5. Select the preferred setting by operat-
ing the “
” or “ ” switch, and then push
the
switch.
6. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
switch. 7. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.Instruments and controls/Multi function display
– CONTINUED –3-91

Instruments and controls/Multi function display
! Approaching time setting
The setting procedure is the same as
“ Leaving time setting ” F 3-90, but select
the “ Approaching time set ” item in step 3.
& InitializeItems that have been set to your pre-
ference can be initialized. To select an
initialization menu, operate the “
” or “ ”
switch as follows.
! Preparation for initialization
1. Turn the ignition switch to the “ ON ”
position.
2. Push and hold the
button to show
the selection screen.
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“ Initialize ” item. Then, push the
button. ! Reset to factory default settings
1. Perform the preparation steps accord-
ing to “ Preparation for initialization ” F 3-
92.
2. Operate the “ ” or “ ” switch to
select the “ Reset to Defaults ” item. Then
push the
button. 3. The system will prompt a Yes/No
dialogue ( “ No ” is selected first). To return
to the factory default settings, select “ Ye s ”
by operating the “
” switch.
4. Confirm the setting by pushing the
button.3-92

5. The system will notify you that the
setting is complete. ! Lifetime fuel consumption resetting
1. Perform the preparation steps accord-
ing to “ Preparation for initialization ” F 3-
92.
2. Operate the “ ” or “ ” switch to
select the “ Lifetime Fuel Consumption
Resetting ” item. Then push the
button. 3. The system will prompt a Yes/No
dialogue ( “ No ” is selected first). To reset
the lifetime fuel consumption, select “ Ye s ”
by operating the “
” switch.
4. Confirm the setting by pushing the
button.Instruments and controls/Multi function display
– CONTINUED –3-93

Instruments and controls/Light control switch
5. Reconfirmation will be displayed. If
you are sure you want to proceed, select
“ Ye s ” by operating the “
” switch.
6. Confirm the setting again by pushing
the
button. 7. The system will notify you that the
setting is complete. Light control switch CAUTION. Use of any lights for a long period
of time while the engine is not
running can cause the battery to
discharge.
. Before leaving the vehicle, make
sure that the lights are turned off.
If the vehicle is left unattended
for a long time with the lights
illuminated, the battery may be
discharged.
Models with “ keyless access with
push-button start system ” :
The light control switch operates when the
push-button ignition switch is in the “ ACC ”
or “ ON ” position.
Regardless of the position of the light
control switch, the illuminated lights are
turned off when the push-button ignition
switch is turned off.
Models without “ keyless access with
push-button start system ” :
The light control switch operates when the
key is inserted in the ignition switch.
Regardless of the position of the light
control switch, the illuminated lights are3-94

turned off when the key is removed from
the ignition switch.
NOTE The light control switch can be oper-
ated (except auto on/off headlights),
even under the following conditions.
. when the key is not inserted into the
ignition switch (models without “ key-
less access with push-button start
system ” )
. when the push-button ignition
switch is turned off (models with “ key-
less access with push-button start
system ” )
If the driver ’ s door is opened while the
headlights are illuminated under such
conditions, the chirp sound will inform
the driver that the lights are illumi-
nated. & Headlights
To turn on the headlights, turn the knob on
the end of the turn signal lever.
“ ” position
Headlights, parking lights, front side mar-
ker lights, rear side marker lights, tail lights
and license plate lights are on.
“
” position
Parking lights, front side marker lights,
rear side marker lights, tail lights and
license plate lights are on. “
” position: auto on/off headlights (if
equipped)
When the ignition switch is in the “ ON ”
position, headlights, parking lights, front
side marker lights, rear side marker lights,
tail lights and license plate lights are
automatically on or off depending on the
level of the ambient light.
“
” position
The headlights are all off.
NOTE The sensitivity of the auto on/off head-
lights can be changed by a SUBARU
dealer. Consult your SUBARU dealer
for details. Also, for models with a multi
function display, the setting can be
changed using the display. For details,
refer to “ Auto light sensor sensitivity
setting ” F 3-88.Instruments and controls/Light control switch
– CONTINUED –3-95