2016 NISSAN NOTE wiring

TM-116
< WIRING DIAGRAM >[CVT: RE0F11A]
CVT CONTROL SYSTEM
AADIA0784GB
Revision: August 2015
2016 Versa Note

cardiagn.com

CVT CONTROL SYSTEMTM-117
< WIRING DIAGRAM > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
AADIA0785GB
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-118
< WIRING DIAGRAM >[CVT: RE0F11A]
CVT CONTROL SYSTEM
ABDIA1738GB
Revision: August 2015
2016 Versa Note

cardiagn.com

CVT SHIFT LOCK SYSTEMTM-119
< WIRING DIAGRAM > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CVT SHIFT LOCK SYSTEM
Wiring DiagramINFOID:0000000012431039
ABDWA0916GB
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-120
< WIRING DIAGRAM >[CVT: RE0F11A]
CVT SHIFT LOCK SYSTEM
ABDIA1739GB
Revision: August 2015
2016 Versa Note

cardiagn.com

CVT SHIFT LOCK SYSTEMTM-121
< WIRING DIAGRAM > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ABDIA1068GB
Revision: August 2015 2016 Versa Note

cardiagn.com

U0073 COMMUNICATION BUS A OFFTM-135
< DTC/CIRCUIT DIAGNOSIS > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
DTC/CIRCUIT DIAGNOSIS
U0073 COMMUNICATION BUS A OFF
DescriptionINFOID:0000000012431053
CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communica tion speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independently ). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000012431054
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for at least 5 seconds.
2. Check the DTC.
Is
“U0073” detected?
YES >> Go to TM-135, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431055
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U0073 Control Module Communica-
tion Bus A Off TCM communication blockage lasts for 2 sec-
onds or more when turning ON the ignition
switch. (Communication not established.) Harness or connector
(CAN communication line is error)
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-136
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F11A]
U0100 LOST COMMUNICATION (ECM A)
U0100 LOST COMMUNICATION (ECM A)
DescriptionINFOID:0000000012431056
CAN (Controller Area Network) is a serial communication
line for real-time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehi cle, and each control unit shares information and links
with other control units during operation (not independently). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L li ne) allowing a high rate of information transmission
with less wiring. Each control unit transmits/recei ves data but selectively reads required data only.
DTC LogicINFOID:0000000012431057
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for at least 5 seconds.
2. Check the DTC.
Is
“U0100” detected?
YES >> Go to TM-136, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431058
For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".
DTC Trouble diagnosis name DTC detection conditionPossible causes
U0100 Lost Communication With
ECM/PCM A When the ignition switch is ON, TCM is un-
able to receive the CAN communications
signal from ECM continuously for 2 sec-
onds or more. •ECM
• Harness or connector
(CAN communication line is open or
shorted)
Revision: August 2015 2016 Versa Note

cardiagn.com