2016 NISSAN NOTE battery

BCS
BCM
BCS-41
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
44
(LG) Ground Rear wiper autostop
switch
InputPush-button ig-
nition switch ON Rear wiper stop position
Battery voltage
Any position other than
rear wiper stop position 0V
45
(BG) Ground
Door switch (AS)
signal Input
Front door
switch RH OFF (front RH door
closed)
7.0 - 8.0 V
ON (front RH door open) 0 V
46
(BR) Ground Door switch (RR)
signal
InputRear door
switch RH OFF (rear RH door
closed)
7.0 - 8.0 V
ON (rear RH door open) 0 V
47
(SB) Ground Door switch (DR)
signal
InputFront door
switch LH OFF (front LH door
closed)
7.0 - 8.0 V
ON (front LH door open) 0 V
48
(W) Ground Door switch (RL)
signal InputRear door
switch LH OFF (rear LH door closed)
7.0 - 8.0 V
ON (rear LH door open) 0 V
49
(L) Ground Cargo lamp control Output Back door is closed (cargo lamp turns OFF)
Battery voltage
Back door is opened (cargo lamp turns ON) 0 – 1 V
50
(G) Ground Door unlock output
(back)
Output Back door UNLOCK (Actuator is acti-
vated)
0 V
Actuator is not activated Battery voltage
51
(W) Ground
Request sw (back
door) signal Input
Back door re-
quest switch ON (Pressed)
0 – 1.5 V
OFF (Not pressed) Battery voltage
54
(R) Ground Rear wiper output Output Rear wiper OFF (stopped)
0V
ON (activated) Battery voltage
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4960J
PKIB4960J
PKIB4960J
PKIB4960J
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-42
< ECU DIAGNOSIS INFORMATION >[WITH INTELLIGENT KEY SYSTEM]
BCM
55
(G) Ground Door unlock output
(RR, RL)
Output Rear doors UNLOCK (Actuator is acti-
vated)
Battery voltage
Actuator is not activated 0 V
56
(W) Ground Battery saver output Output Interior room lamp battery saver timed out
0 V
Except when interior room lamp battery sav-
er timed out Battery voltage
57
(Y) Ground Battery power sup-
ply Input Push-button ignition switch OFF
Battery voltage
59
(G) Ground Door unlock output
(AS)
Output Front RH door UNLOCK (Actuator is acti-
vated)
Battery voltage
Actuator is not activated 0 V
60
(V) Ground Flasher output
(LEFT)
OutputPush-button ig-
nition switch ON Turn signal switch OFF
0 V
Turn signal switch LH 6.5 V
61
(W) Ground Flasher output
(RIGHT)
OutputPush-button ig-
nition switch ON Turn signal switch OFF
0 V
Turn signal switch RH 6.5 V
63
(R) Ground Room lamp control Output
Interior room
lampOFF
Battery voltage
ON 0 – 1.0 V
65
(SB) Ground Door lock output Output All doors LOCK (Actuator is activat-
ed)
Battery voltage
Actuator is not activated 0 V
66
(G) Ground
Door unlock output
(DR) Output Front LH door UNLOCK (Actuator is acti-
vated)
Battery voltage
Actuator is not activated 0 V
67
(B) Ground Ground
Output Push-button ignition switch ON 0 V
68
(L) Ground Power window pow-
er supply (RAP)
Output Push-button ignition switch ON
Battery voltage
70
(G) Ground
Battery power sup-
ply Input Push-button ignition switch OFF
Battery voltage
72
(L) Ground A/C indicator
Input— —
75
(GR) Ground
Request sw (DR)
signal In
put Drive
r
door re-
quest switch ON (Pressed)
0 – 1.5 V
OFF (Not pressed) Battery voltage
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIC6370E
PKIC6370E
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-43
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
76
(L) Ground Engine start sw Input
Push-button ig-
nition switchSTART pressed
0 – 1.5 V
Not pressed Battery voltage
78
(P) Ground Door antenna (DR) + Output Push-button ig-
nition switch ON
Driver door re-
quest switch
pressedIntelligent Key not in an-
tenna detection area
(Approx. 2 m)
Intelligent Key in antenna
detection area
(80 cm or less)
79
(V) Ground Door antenna (DR) - Output Push-button ig-
nition switch ON
Driver door re-
quest switch
pressedIntelligent Key not in an-
tenna detection area
(Approx. 2 m)
Intelligent Key in antenna
detection area
(80 cm or less)
80
(LG) Ground Door antenna (AS) + Output Push-button ig-
nition switch ON
Passenger door
request switch
pressedIntelligent Key not in an-
tenna detection area
(Approx. 2 m)
Intelligent Key in antenna
detection area
(80 cm or less)
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
JMKIA5954GB
JMKIA5955GB
JMKIA5954GB
JMKIA5955GB
JMKIA5954GB
JMKIA5955GB
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
BCM
BCS-47
< ECU DIAGNOSIS INFORMATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
1: With CVT
2: With M/T 90
(W) Ground Push-button ignition
switch illumination
power supply OutputPush-button ig-
nition switch il-
lumination ON
Battery voltage
OFF 0 – 1.5 V
91
(V) Ground ACC/ON indicator
lamp
OutputPush-button ig-
nition switch OFF
Battery voltage
ACC or ON 0 – 1.5 V
92
(B) Ground Push-button ignition
switch illumination
lamp Output
Push-button ig-
nition switch il-
lumination ON
5.5 V
OFF 0 – 1.5 V
93
(R) Ground Intelligent Key warn-
ing buzzer OutputIntelligent Key
warning buzzer Sounding
0 – 1.5 V
Not sounding Battery voltage
96
(SB) Ground Accessory relay
control OutputIgnition Push-
button switch OFF
0 – 0.5 V
ACC or ON Battery voltage
97
(R) Ground Starter relay control Output Push-button ig-
nition switch ONSelector lever in P (Park)
or N (Neutral) position
Battery voltage
Selector lever not in P
(Park) or N (Neutral) posi-
tion 0 – 0.5 V
98
(BG) Ground Ignition relay (IPDM
E/R) control OutputPush-button ig-
nition switch OFF or ACC
Battery voltage
ON 0 – 0.5 V
99
(GR) Ground Ignition relay (F/B)
control OutputPush-button ig-
nition switch OFF or ACC
0 – 0.5 V
ON Battery voltage
100 (L) Ground Request sw (AS)
signal InputPassenger door
request switch ON (Pressed)
0 – 1.5 V
OFF (Not pressed) Battery voltage
101 (V) Ground Clutch interlock
switch
InputClutch interlock
sw
itch OFF (c
l
utch pedal is not
depressed) 0V
ON (clutch pedal is de-
pressed) Battery voltage
102
1
(BR) Ground P/N position
Input Selector leverSelector lever in P (Park)
or N (Neutral) position
Battery voltage
Selector lever not in P
(Park) or N (Neutral) posi-
tion 0 – 1.5 V
102
2
(BR) Ground Neutral sw
Input Selector leverSelector lever in N (Neu-
tral) position
Battery voltage
Selector lever not in N
(Neutral) position 0 – 1.5 V
103
(LG) Ground Front defrost switch Input
——
104 (V) Ground CVT shift selector
(park position
switch) power sup-
ply Output Push-button ignition switch ON
Battery voltage
105
(SB) Ground Stop lamp switch 2 Input Push-button ignition switch OFF
Battery voltage
106 (Y) Ground Blower relay control Output
Push-button ig-
nition switchOFF or ACC
0 – 0.5 V
ON Battery voltage
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-66
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2562 LOW VOLTAGE
B2562 LOW VOLTAGE
DTC LogicINFOID:0000000012432351
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2. Turn ignition switch OFF.
3. Perform the “Self Diagnostic Result” of “BCM” with CONSULT, after the ignition switch has been turned
ON for 120 seconds or more.
Is any DTC detected?
YES >> Refer to BCS-66, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000012432352
1. CHECK BATTERY VOLTAGE
Check battery voltage.
Is battery voltage less than 8.8V?
YES >> Charge battery and retest. Refer to PG-61, "Work Flow".
NO >> GO TO 2.
2. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit. Refer to BCS-67, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. BCM SELF DIAGNOSTIC RESULT
Perform “Self Diagnostic Result” of “BCM” with CONSULT. Refer to BCS-25, "
BCM : CONSULT Function
(BCM - BCM)".
Is DTC B2562 CRNT?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> Refer to GI-42, "
Intermittent Incident".
CONSULT Display DTC Detection Condition Possible Cause
LOW VOLTAGE
[B2562] When the power supply voltage to BCM remains
less than 8.8 V for 120 seconds or more • Harness or connector (power supply circuit)
• Vehicle battery
Revision: August 2015
2016 Versa Note

cardiagn.com

BCS
POWER SUPPLY AND GROUND CIRCUITBCS-67
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000012432353
Regarding Wiring Diagram information, refer to
BCS-52, "Wiring Diagram".
1.CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M99.
2. Check voltage between BCM connector M99 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM connector M99 and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
Terminal No. Signal nameFuses and fusible link No.
57 Battery power supply 12 (10A)
70 G (40A)
BCM
Ground Voltage
Connector Terminal
M99 57
— Battery voltage
70
BCM GroundContinuity
Connector Terminal
M99 67—Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS
NORMAL OPERATING CONDITIONBCS-73
< SYMPTOM DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
K L
B A
O P
N
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000012432357
SHIPPING MODE
• Shipping mode inhibits battery power consumption during transportation or storage of the vehicle. Vehicle is
set to shipping mode before being shipped from the factory.
• When ignition switch is OFF, BCM operates shipping mode.
• BCM control function is limited in shipping mode. Re mote keyless entry function does not operate in ship-
ping mode.
• For shipping mode cancel operation, refer to BCS-61, "
Work Procedure".
NOTE:
Do not cancel shipping mode during storage of the v ehicle. Shipping mode should not be canceled until just
prior to customer delivery.
TRANSIT MODE
• BCM is in transit mode if turn signal indicators in combination meter illuminate for 1 minute when ignition
switch is turned from OFF to ON.
• In this case, cancel operation must be performed.
• For transit mode cancel operation, refer to BCS-62, "
Work Procedure".
NOTE:
Do not cancel transit mode during storage of the vehicl e. Transit mode should not be canceled until just prior
to customer delivery.
Revision: August 2015 2016 Versa Note

cardiagn.com

BCS-74
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
BCM (BODY CONTROL MODULE)
REMOVAL AND INSTALLATION
BCM (BODY CONTROL MODULE)
Removal and InstallationINFOID:0000000012432358
REMOVAL
CAUTION:
Before replacing BCM, perform “READ CONFIGURATI
ON” to save or print current vehicle specifica-
tion. Refer to BCS-59, "
Description".
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-70,
"Removal and Installation (Battery)".
2. Remove instrument lower panel LH. Refer to IP-24, "
Removal and Installation".
3. Remove screws (A) and remove the BCM (1) from the steering member and position aside.
: Front
4. Disconnect the harness connectors from the BCM.
5. Remove relays from relay bracket.
6. Remove relay bracket from BCM to transfer to new BCM.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Perform “CONFIGURATION (BCM)” when replacing BCM. Refer to BCS-59, "
Description".
• Make sure to perform the system initialization (NATS) (if equipped) when replacing BCM. Refer to
BCS-58, "
Description".
• When replacing BCM, if new BCM does not come wi th keyfobs attached, all existing keyfobs must be
re-registered.
• For initialization and registration of Intelligent Key, refer to CONSULT Immobilizer mode and fol- lowthe on-screen instructions.
ALMIA0656ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com