2016 NISSAN NOTE key

DOOR SWITCHDLK-99
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK DOOR SWITCH
Refer to DLK-99, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace malfunctioning door switch.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Component InspectionINFOID:0000000012430039
1.CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Disconnect malfunctioning door switch connector.
3. Check continuity between door switch terminals.
Is the inspection result normal?
Door switch BCM
Continuity
Connector TerminalConnector Terminal
Front door switch
LH B8
3M10 0 47
Ye s
Front door switch
RH
B16
45
Rear door switch
LH B6
48
Rear door switch
RH B17
46
Door switch GroundContinuity
Connector Terminal
Front door switch LH B8
3N o
Front door switch RH
B16
Rear door switch LH B6
Rear door switch RH B17
Door switch
Condition Continuity
Te r m i n a l
Front door switch
LH
3Ground part of door
switch Door switch Pressed
No
Released Yes
Front door switch
RH Pressed
No
Released Yes
Rear door switch
LH Pressed
No
Released Yes
Rear door switch
RH Pressed
No
Released Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-100
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR SWITCH
YES >> Inspection End.
NO >> Replace malfunction door switch.
Revision: August 2015
2016 Versa Note

cardiagn.com

HAZARD FUNCTIONDLK-101
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
HAZARD FUNCTION
Component Function CheckINFOID:0000000012430040
1.CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “FLASHER” in “Active Test.
3. Touch “LH” or “RH” to check that it works normally.
Is the inspection result normal?
YES >> Hazard warning lamp circuit is OK.
NO >> Refer to DLK-101, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430041
1.CHECK HAZARD SWITCH CIRCUIT
Refer to EXL-85, "
Component Function Check".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-102
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Component Function CheckINFOID:0000000012542553
1.CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “OUTSIDE BUZZER ” in “ACTIVE TEST” mode.
3. Touch “On” or “Off” to check that it works normally.
Is the inspection result normal?
YES >> Intelligent Key warning buzzer is OK.
NO >> Refer to DLK-102, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012542554
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10 A fuse [No. 8, located in fuse block (J/B)].
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1. Disconnect Intelligent Key warning buzzer connector.
2. Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK INTELLIGENT KEY WARNING BUZZER
(+)
(–)Vol tag e
(Approx.)
Intelligent Key warning buzzer
Connector Terminal
E70 1Ground Battery voltage
BCM Intelligent Key warning buzzer
Continuity
Connector TerminalConnector Terminal
M98 93E70 3Yes
BCM GroundContinuity
Connector Terminal
M98 93 No
Revision: August 2015 2016 Versa Note

cardiagn.com

INTELLIGENT KEY WARNING BUZZERDLK-103
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Refer to DLK-103, "Component Inspection".
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> Replace Intelligent Key warning buzzer. Refer to DLK-186, "
Removal and Installation".
Component InspectionINFOID:0000000012542555
1.CHECK INTELLIGENT KEY WARNING BUZZER
1. Turn ignition switch OFF.
2. Disconnect Intelligent Key warning buzzer connector.
3. Connect battery power supply directly to Intelligent Key warning buzzer terminals and check the opera- tion.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace Intelligent Key warning buzzer. Refer to DLK-186, "
Removal and Installation".
Intelligent Key warning buzzer
Operation
Te r m i n a l
(+) (− )
1 3Buzzer sounds
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-104
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY
INTELLIGENT KEY
Component Function CheckINFOID:0000000012430042
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength.
• Confirm vehicle Intelligent Key antenna signal strength.
1.CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “Data Monitor”.
3. Check that the function operates normall y according to the following conditions:
Is the inspection result normal?
YES >> Intelligent Key is OK.
NO >> Refer to DLK-104, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430043
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength.
• Confirm vehicle Intelligent Key antenna signal strength.
1.CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300 Ω) so that the
current value becomes about 10 mA. Refer to DLK-188, "
Removal
and Installation".
Is the measurement value within the specification?
YES >> Replace Intelligent Key.
NO >> Replace Intelligent Key battery.
Monitor item Condition
RKE OPE COUN1 Check that the numerical value is changing while operating on the Intelligent Key.
Standard : Approx. 2.5 - 3.0V
OCC0607D
Revision: August 2015 2016 Versa Note

cardiagn.com

KEY WARNING LAMPDLK-105
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
KEY WARNING LAMP
Component Function CheckINFOID:0000000012430044
1.CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INDICATOR” in “Active Test”.
3. Touch “KEY IND” or “KEY ON” to check that it works normally.
Is the inspection result normal?
YES >> Key warning lamp is OK.
NO >> Refer to DLK-105, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430045
1.CHECK KEY WARNING LAMP
Refer to DLK-27, "
WARNING FUNCTION : System Description".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness.
2.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-106
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Component Function CheckINFOID:0000000012430046
1.CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “Data Monitor”.
3. Check that the function operates normall y according to the following conditions:
Is the inspection result normal?
YES >> Remote keyless entry receiver is OK.
NO for USA >>Refer to DLK-106, "
Diagnosis Procedure (For USA)".
NO for Canada>>Refer to DLK-107, "
Diagnosis Procedure (For Canada)".
Diagnosis Procedure (For USA)INFOID:0000000012430047
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK REMOTE K EYLESS ENTRY RECEIVER CIRCUIT
1. Disconnect BCM and remote keyless entry receiver connectors.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
Monitor item Condition
RKE OPE COUN1 Checks whether value changes when operating Intelligent Key.
(+)
(–)Condition Signal
(Reference value)
BCM
Connector Terminal
M97 38GroundPush-button igni-
tion OFF or ACC
0 – 0.5 V
Push-button igni-
tion ON Battery voltage
BCM
Remote keyless entry receiver
Continuity
Connector TerminalConnector Terminal
M 973 8M 94 2 Y es
(+) (–)Continuity
BCM
Connector Terminal
M97 38Ground No
Revision: August 2015 2016 Versa Note

cardiagn.com