2016 NISSAN NOTE abs

DIAGNOSIS SYSTEM (ECM)EC-61
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*: The items are the same as those of 1st trip freeze frame data.
DATA MONITOR MODE
NOTE:
• The following table includes information (items) inapplicable to this vehicle. For information (items) applica-
ble to this vehicle, refer to CONSULT display items.
• For reference values of the following items, refer to EC-71, "
Reference Value".
Monitored Item
Freeze frame data item* Description
Detected DTC The engine control component part/control system has a trouble code, it is displayed as PXXXX.
(Refer to
EC-87, "
DTCIndex".)
FUEL SYS-B1 • “Fuel injection system status” at the moment a malfunction is detected is displayed.
• One mode in the following is displayed.
Mode2: Open loop due to detected system malfunction
Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)
Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control
Mode5: Open loop - has not yet satisfied condition to go to closed loop
FUEL SYS-B2
CAL/LD VALUE [%]
The calculated load value at the moment a malfunction is detected is displayed.
COOLANT TEMP [ °C] or [ °F] The engine coolant temperature at the moment a malfunction is detected is displayed.
L-FUEL TRM-B1 [%] • “Long-term fuel trim” at the moment a malfunction is detected is displayed.
• The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule than short-term fuel trim.
L-FUEL TRM-B2 [%]
S-FUEL TRM-B1 [%]
• “Short-term fuel trim” at the moment a malfunction is detected is displayed.
• The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel schedule.
S-FUEL TRM-B2 [%]
ENGINE SPEED [rpm]
The engine speed at the moment a malfunction is detected is displayed.
VEHICL SPEED [km/h] or [mph] The vehicle speed at the moment a malfunction is detected is displayed.
ABSOL TH·P/S [%] The throttle valve opening angle at the moment a malfunct ion is detected is displayed.
B/FUEL SCHDL [msec] The base fuel schedule at the moment a malfunction is detected is displayed.
INT/A TEMP SE [° C] or [°F] The intake air temperature at the moment a malfunction is detected is displayed.
INT MANI PRES [kPa] These items are displayed but are not applicable to this model.
COMBUST CONDITION
Monitored item Unit DescriptionRemarks
IDLE REQUEST* YES/NO • Displays the idle request status sent from HPCM.
- YES: Idle request received
- NO: No idle request
MIL ON REQUEST* YES/NO • Displays the MIL ON request status sent from
HPCM.
- YES: MIL ON request received
- NO: No MIL ON request
ENGINE NO-LOAD* YES/NO • Displays the clutch 1 disengagement/engage-
ment status sent from HPCM.
- YES: Clutch 1 disengaged
- NO: Clutch 1 engaged
READY STATE* YES/NO • Displays the clutch 1 disengagement/engage-
ment status sent from HPCM.
- YES: READY state
- NO: Not in READY state
ENG SPEED rpmIndicates the engine speed computed from the sig-
nal of the crankshaft position sensor (POS) and
camshaft position sensor (PHASE). • Accuracy becomes poor if engine
speed drops below the idle rpm.
• If the signal is interrupted while the
engine is running, an abnormal value
may be indicated.
Revision: August 2015 2016 Versa Note

cardiagn.com

DIAGNOSIS SYSTEM (ECM)EC-65
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
CRUISE LAMP ON/OFF
Indicates [ON/OFF] cond
ition of CRUISE lamp de-
termined by the ECM according to the input signals.
SET LAMP* ON/OFFIndicates [ON/OFF] condition of SET lamp deter-
mined by the ECM according to the input signals.
ALT DUTY %Indicates the duty ratio of the power generation
command value. The ratio is calculated by ECM
based on the battery current sensor signal.
BAT CUR SEN mVThe signal voltage of battery current sensor is dis-
played.
A/F ADJ-B1 —Indicates the correction of a factor stored in ECM.
The factor is calculated from the difference between
the target air-fuel ratio stored in ECM and the air-
fuel ratio calculated from A/F sensor 1 signal.
P/N POSI SW ON/OFFIndicates [ON/OFF] condition from the park/neutral
position (PNP) signal.
INT/A TEMP SE °C or ° F The intake air temperature (determined by the sig-
nal voltage of the intake air temperature sensor) is
indicated.
AC PRESS SEN VThe signal voltage from the refrigerant pressure
sensor is displayed.
CLUTCH P/P SW ON/OFF Indicates [ON/OFF] condition clutch pedal position
switch signals. Models other than M/T models always
display OFF.
VTC DTY EX B1 %• The control value of the exhaust valve timing con-
trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.
• The advance angle becomes larger as the value
increases.
THRTL STK CNT
B1* ——
EVAP LEAK DIAG YET/CMPLT • Indicates the condition of EVAP leak diagnosis.
YET: EVAP leak diagnosis has not been per-
formed yet.
CMPLT: EVAP leak diagnosis has been per-
formed successfully.
EVAP DIAG READY ON/OFF • Indicates the ready condition of EVAP leak diag-
nosis.
ON: Diagnosis has been ready condition.
OFF: Diagnosis has not been ready condition.
A/F SEN1
DIAG1(B1) INCMP/CM-
PLT • Indicates DTC P015A or P015B self-diagnosis
condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
A/F SEN1
DIAG2(B1) INCMP/CM-
PLT • Indicates DTC P014C or P014D self-diagnosis
condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
A/F SEN1
DIAG3(B1) ABSNT/
PRSNT • Indicates DTC P014C, P014D, P015A or P015B
self-diagnosis condition.
- ABSNT: The vehicle condition is not within the di- agnosis range.
- PRSNT: The vehicle condition is within the diag-
nosis range.
HO2 S2 DIAG2(B1) INCMP/CM-
PLT • Indicates DTC P0139 self-diagnosis (slow re-
sponse) condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
EOP SENSOR mV The signal voltage of EOP sensor is displayed.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-66
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
HO2 S2 DIAG1(B1)INCMP/CM-
PLT • Indicates DTC P0139 self-diagnosis (delayed re-
sponse) condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
SYSTEM 1 DIAG-
NOSIS A B1 INCMP/CM-
PLT • Indicates DTC P219A self-diagnosis condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
SYSTEM 1 DIAG-
NOSIS B B1 ABSNT/
PRSNT • Indicates DTC P219A self-diagnosis condition.
- ABSNT: Self-dia
gnosis standby
- PRSNT: Under self-diagnosis
A/GRLL SHTTR PO-
SITION F/CLOSE
MOVING
F/OPENUNIDTF • Indicates the status of active grille shutter.
- F/CLOSE: Active grille shutter is fully closed.
- MOVING: Active grille shutter is in motion.
- F/OPEN: Active grille shutter is fully opened.
- UNIDTF: Unable to specify the shutter position.
A/GRLL SHTTR
CALIBRATION INCMP/CM-
PLT • Indicates initial position learning status of active
grille shutter.
- CMPLT: The leaning is complete.
- INCOMP: The learning is incomplete.
A/GRLL SHTTR
CIRCUIT DIAG OK/NG• Indicates the diagnosis result of active grille shut-
ter circuit.
-OK: Normal.
- NG: Malfunction detected.
A/GRLL SHTTR
TEMP DIAG OK/NG• Indicates the diagnosis result of active grille shut-
ter actuator temperature status.
-OK: Normal
- NG: Abnormal temperature detected.
A/GRLL SHTTR
VOLT DIAG OK/NG• Indicates the diagnosis result of active grille shut-
ter voltage status.
-OK: Normal
- NG: Abnormal voltage detected.
A/GRLL SHTTR
OVER RUN OK/NG• Indicates active grille shutter moves beyond nor-
mal moving limit.
-OK: Normal
- NG: Malfunction detected.
A/GRLL SHTTR
STUCK OK/NG• Indicates the diagnosis result of active grille shut-
ter stuck or the operation range less than normal.
-OK: Normal
- NG: Malfunction detected.
A/GRLL SHTTR
CALIB DIAG OK/NG• Indicates the diagnosis result of initial position
learning of active grille shutter.
-OK: Normal
- NG: Deficiency detected.
A/F-S ATMSPHRC
CRCT B1 —Displays a determined value of atmospheric correc-
tion factor necessary for correcting an A/F sensor
signal input to ECM. The signal used for the correc-
tion is an A/F sensor signal transmitted while driving
under atmospheric pressure.
A/F-S ATMSPHRC
CRCT B2 —Displays a determined value of atmospheric correc-
tion factor necessary for correcting an A/F sensor
signal input to ECM. The signal used for the correc-
tion is an A/F sensor signal transmitted while driving
under atmospheric pressure.
A/F-S ATMSPHRC
CRCT UP B1 countDisplays the number of updates of the A/F sensor
atmospheric correction factor.
A/F-S ATMSPHRC
CR CT UP B2 coun
t Dis

plays the number of updates of the A/F sensor
atmospheric correction factor.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note

cardiagn.com

DIAGNOSIS SYSTEM (ECM)EC-67
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*: The item is indicated, but not used.
NOTE:
Any monitored item that does not match the vehicle
being diagnosed is deleted from the display automatically.
WORK SUPPORT MODE
Work Item
*: This function is not necessary in the usual service procedure.
ACTIVE TEST MODE
Test Item
A/F IMBALNC DIAG-
CPS STATABSNT/
PRSNT Indicates DTC P219C – P219F self-diagnosis con-
dition.
• ABSNT: The vehicle condition is not within the di-
agnosis range.
• PRSNT: The vehicle condition is within the diag-
nosis range.
A/F IMBLNC DIAG-
CPS CMPLT INCMP/CM-
PLT Indicates DTC P219C – P219F self-diagnosis con-
dition.
• INCMP: Self-diagnosis is incomplete.
• CMPLT: Self-diagnosis is complete.
Monitored item Unit
DescriptionRemarks
WORK ITEMCONDITION USAGE
IDLE AIR VOL LEARN The idle air volume that keeps the engine within the specified range is memorized in ECM. When learning the idle air volume
EVAP SYSTEM CLOSE Close the EVAP canister vent control valve in order to make
EVAP system close under the following conditions.
• Ignition switch ON
• Engine not running
• Ambient temperature is above 0 °C (32 °F)
• No vacuum and no high pressure in EVAP system
• Fuel tank temperature is more than 0 °C (32 °F)
• Within 10 minutes after st arting “EVAP SYSTEM CLOSE”
• When trying to execute “E VAP SYSTEM CLOSE” under the
condition except above, CONSULT will discontinue it and
display appropriate instruction.
NOTE:
When starting engine, CONSULT may display “Battery volt-
age is low. Charge battery”, even in using charged battery. When detecting EVAP vapor leak
point of EVAP system
FUEL PRESSURE RELEASE Fuel pump will stop by touching “START” during idling. Crank a few times after engine stalls. When releasing fuel pressure from
fuel line
TARGET IDLE RPM ADJ* Idle condition When setting target idle speed
VIN REGISTRATION In this mode, VIN is regist ered in ECM.When registering VIN in ECM
SELF-LEARNING CONT The coefficient of self-learning control mixture ratio returns to the original coefficient. When clearing mixture ratio self-
learning value
TARGET IGN TIM ADJ* Idle condition When adjusting target ignition timing
CLSD THL POS LEARN Ignition on and engine stopped. When learning throttle valve closed
position
SAVING DATA FOR REPLC
CPU In this mode, save data that is in ECM.
When ECM is replaced.
WRITING DATA FOR REPLC
CPU In this mode, write data stor
ed by "SAVE DATA FOR CPU RE-
PLC" in work support mode to EC When ECM is replaced.
Revision: August 2015
2016 Versa Note

cardiagn.com

DIAGNOSIS SYSTEM (ECM)EC-69
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
DTC WORK SUPPORT MODE
Test Item
SRT & P-DTC MODE
SRT STATUS Mode
• For items whose SRT codes are set, “CMPLT” is di
splayed on the CONSULT screen; for items whose SRT
codes are not set, “INCMP” is displayed.
• “SRT STATUS” provides the presence or absenc e of permanent DTCs stored in ECM memory.
PERMANENT DTC STATUS Mode
How to display permanent DTC status1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select “PERMANENT DTC STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
NOTE:
Permanent DTCs stored in ECM memory are displayed on the CONSULT screen to show if a driving pat-
tern required for erasing permanent DTCs is complete (CMPLT) or incomplete (INCMP).
CAUTION:
Since the “PERMANENT DTC STATUS ” screen displays the previous trip information, repeat the
following twice to update the in formation: “Ignition switch OFF”, “Wait for more than 10 seconds”
and “Ignition switch ON”.
NOTE:
This mode is not used in regions that permanent DTCs are not regulated by law.
SRT WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.
PERMANENT DTC WORK SUPPORT Mode
Test modeTest itemCorresponding DTC No. Reference page
A/F SEN1 A/F SEN1 (B1) P1276
P0130EC-213, "
DTC Logic"
A/F SENSOR1 (B1) P014C/P014D P014C/P014DEC-243, "DTC Logic"
A/F SENSOR1 (B1) P015A/P015BP015A/P015B EC-243, "DTC Logic"
EVAPORATIVE SYSTEM PURG FLOW P0441 P0441
EC-290, "DTC Logic"
PURG VOL CN/V P1444P0443EC-295, "DTC Logic"
HO2S2 HO2S2 (B1) P1146
P0138EC-229, "
DTC Logic"
HO2S2 (B1) P1147 P0137EC-223, "DTC Logic"
HO2S2 (B1) P0139 P0139EC-237, "DTC Logic"
JSBIA0062GB
Revision: August 2015 2016 Versa Note

cardiagn.com

ECM
EC-75
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
A/F SEN1
DIAG3(B1)
• The vehicle condition is not within the diagnosis range of DTC P014C, P014D,
P015A or P015B. ABSNT
• The vehicle condition is within the diagnosis range of DTC P014C, P014D, P015A or P015B. PRSNT
HO2 S2 DIAG2(B1) • DTC P0139 self-diagnosis (slow response) is incomplete.
INCMP
• DTC P0139 self-diagnosis (slow response) is complete. CMPLT
SYSTEM 1 DIAG-
NOSIS A B1 DTC P219A self-diagnosis is incomplete.
INCMP
DTC P219A self-diagnosis is complete. CMPLT
SYSTEM 1 DIAG-
NOSIS B B1 DTC P219A self-diagnosis
is on standby. ABSENT
DTC P219A self-diagnosis is under diagnosis. PRSENT
EOP SENSOR • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idle
Approx 1,000 - 2,000 mV
2,000 rpm Approx 1,500 - 3,500 mV
HO2 S2 DIAG1(B1) • DTC P0139 self-diagnosis (delayed response) is incomplete.
INCMP
• DTC P0139 self-diagnosis (delayed response) is complete. CMPLT
A/GRLL SHTTR PO-
SITION • Engine RPM: idle speed.
• Vehicle speed: 0 km/h (0 MPH).
F/OPEN
• Vehicle speed: 30 km/h (19 MPH) or faster. (Comply the condition of active grille shutter operation). F/OPEN
→MOVING →F/
CLOSE
A/GRLL SHTTR
CALIBRATION • Turn ignition switch OFF→ ON
• Drive the vehicle at a speed more than 6 km/h (4 MPH) for the first time.
CMPLT
• Turn ignition switch OFF → ON.
• When the vehicle speed does not reach 6 km/h (4 MPH). INCMP
A/GRLL SHTTR
CIRCUIT DIAG • Malfunction of active grill shutter power supply is detected.
NG
• Malfunction of active grill shutter power supply is not detected. OK
A/GRLL SHTTR
TEMP DIAG • Abnormal temperature of active grill shutter actuator is detected.
NG
• Abnormal temperature of active grill shutter actuator is not detected. OK
A/GRLL SHTTR
VOLT DIAG • Abnormal voltage of active grill shutter circuit is detected.
NG
• Abnormal voltage of active grill shutter circuit is not detected. OK
A/GRLL SHTTR
OVERRUN • Active grill shutter does not stop within normal moving limit.
NG
• Active grill shutter stops within normal moving limit OK
A/GRLL SHTTR
STUCK • Detecting the active grille shutter stuck or the operation range less than nor-
mal. NG
• Not detecting the active grille shutter stuck or the operation range less than normal. OK
A/GRLL SHTTR
CALIB DIAG • Malfunction of active grill shutter initial position learning is detected.
NG
• Malfunction of active grill shutter initial position learning is not detected. OK
A/F-S ATMSPHRC
CRCT B1 Engine: After warming up, idle the engine
Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT B2 Engine: After warming up, idle the engine Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT UP B1 Engine: Running Varies depending on the
number of updates.
A/F-S ATMSPHRC
CRCT UP B2 Engine: Running
Varies depending on the
nu
mber of up
dat

es.
A/F IMBALNC DIAG-
CPS STAT The vehicle condition is not within the diagnosis range of DTC P219C – P219F.
ABSNT
The vehicle condition is within the diagnosis range of DTC P219C – P219F. PRSNT
Monitor Item
Condition Values/Status
Revision: August 2015 2016 Versa Note

cardiagn.com

P014C, P014D, P015A, P015B, A/F SENSOR 1EC-243
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P014C, P014D, P015A, P015B, A/F SENSOR 1
DTC LogicINFOID:0000000012431453
DTC DETECTION LOGIC
To judge malfunctions, this diagnosis measures response time of the A/F signal co
mputed by ECM from the A/
F sensor 1 signal. The time is compensated by engi ne operating (speed and load), fuel feedback control con-
stant, and the A/F sensor 1 temperature index. Judgment is based on whether the compensated time (the A/F
signal cycling time index) is inordinately long or not.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Do you have CONSULT?
YES >> GO TO 2.
NO >> GO TO 5.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1minute under no load.
6. Let engine idle for 1 minute.
7. Increase the engine speed up to about 3,600 rpm and keep it for 10 seconds.
8. Fully release accelerator pedal and then let engine idle for about 1 minute.
9. Check the items status of “DATA MONITOR” as follows. NOTE:
If “PRSNT” changed to “ABSNT”, refer to EC-151, "
Component Function Check".
Is
“PRSNT” displayed on CONSULT screen?
YES >> GO TO 4.
NO >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
Perform DTC confirmation procedure-1 again.
Is
“PRSNT” displayed on CONSULT screen?
YES >> GO TO 4.
NO >> Refer to EC-151, "
Component Function Check".
DTC No. Trouble diagnosis content DTC detecting conditionPossible Cause
P014C Air fuel ratio (A/F) sensor 1 (bank 1) circuit slow re-
sponse • The response time of a A/F sensor 1 signal de-
lays more than the specified time computed by
ECM. • Harness or connectors
(The A/F sensor 1 circuit is open or
shorted.)
• A/F sensor 1
P014D
P015A Air fuel ratio (A/F) sensor 1
(bank 1) circuit delayed re-
sponse
P015B
Data monitor item
Status
A/F SEN1 DIAG3 (B1) PRSNT
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-332
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0500 VSS
P0500 VSS
DescriptionINFOID:0000000012431524
The vehicle speed signal is sent to the combination meter from the “ABS actuator and electric unit (control
unit)” by CAN communication line. The combination meter then sends a signal to the ECM by CAN communi-
cation line.
DTC LogicINFOID:0000000012431525
DTC DETECTION LOGIC
NOTE:
•
If DTC P0500 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
• If DTC P0500 is displayed with DTC P0607, first perform the trouble diagno sis for DTC P0607. Refer
to EC-353, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO >> GO TO 5.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.CHECK VEHICLE SPEED SENSOR FUNCTION
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a
road test is expected to be easier, it is unnecessary to lift the vehicle.
With CONSULT
1. Start engine.
2. Read “VHCL SPEED SE” in “DATA MONITOR” m ode with CONSULT. The vehicle speed on CONSULT
should exceed 10 km/h (6 mph) when rotating wheels with suitable gear position.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Go to EC-333, "
Diagnosis Procedure".
4.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “DATA MONITOR” mode with CONSULT.
2. Warm engine up to normal operating temperature.
3. Maintain the following conditions for at least 60 consecutive seconds. CAUTION:
Always drive vehicle at a safe speed.
DTC No. Trouble diagnosis content DTC detecting condition Possible cause
P0500 Vehicle speed sensor The almost 0 km/h (0 MPH) of vehi-
cle speed signal is sent to ECM even
when vehicle is being driven.• Harness or connectors
(The CAN communication line is open or shorted)
• Harness or connectors
(The vehicle speed signal circuit is open or shorted)
• Combination meter
• ABS actuator and electric unit (control unit)
Revision: August 2015 2016 Versa Note

cardiagn.com