Page 574 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRC-126
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF SWITCH
VDC OFF SWITCH
Component Function CheckINFOID:0000000012430906
1.CHECK VDC OFF SWITCH OPERATION
Check that VDC OFF indicator lamp in combi NISSAN NOTE 2016 Service Repair Manual BRC-126
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF SWITCH
VDC OFF SWITCH
Component Function CheckINFOID:0000000012430906
1.CHECK VDC OFF SWITCH OPERATION
Check that VDC OFF indicator lamp in combi](/manual-img/5/57363/w960_57363-573.png)
BRC-126
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF SWITCH
VDC OFF SWITCH
Component Function CheckINFOID:0000000012430906
1.CHECK VDC OFF SWITCH OPERATION
Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-126, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430907
Regarding Wiring Diagram information, refer to BRC-44, "Wiring Diagram".
1.CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (c ontrol unit) and VDC OFF switch connectors.
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace as necessary.
2.CHECK VDC OFF SWITCH
Check VDC OFF switch. Refer to BRC-127, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace VDC OFF switch. Refer to BRC-146, "
Removal and Installation".
3.CHECK VDC OFF SWITCH SIGNAL
With CONSULT.
1. Connect ABS actuator and electric unit (c ontrol unit) and VDC OFF switch connectors.
2. Turn ignition switch ON.
3. In “Data Monitor” select “OFF SW” and check VDC OFF switch signal.
Is the inspection result normal?
YES >> Refer to BRC-52, "Work Flow".
NO >> GO TO 4.
4.CHECK VDC OFF SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (c ontrol unit) and VDC OFF switch connectors.
3. Check continuity between ABS actuator and electr ic unit (control unit) connector E33 terminal 20 and
VDC OFF switch connector M34 terminal 1.
4. Check continuity between ABS actuator and electric unit (control unit) connector terminal E33 terminal 20 and ground.
Condition DATA MONITOR
VDC OFF switch is pressed and released On
VDC OFF switch is pressed and released again Off
ABS actuator and electric unit (control unit) VDC OFF switch
Continuity
Connector Terminal Connector Terminal
E33 20 M34 1 Yes
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 575 of 3641
![NISSAN NOTE 2016 Service Repair Manual VDC OFF SWITCHBRC-127
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.
5.CH NISSAN NOTE 2016 Service Repair Manual VDC OFF SWITCHBRC-127
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.
5.CH](/manual-img/5/57363/w960_57363-574.png)
VDC OFF SWITCHBRC-127
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.
5.CHECK VDC OFF SW ITCH GROUND CIRCUIT
Check continuity between VDC OFF swit ch connector M34 terminal 2 and ground.
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Repair or replace malfunctioning components.
Component InspectionINFOID:0000000012430908
1.CHECK VDC OFF SWITCH
1. Turn ignition switch OFF.
2. Disconnect VDC OFF switch connector.
3. Check continuity between terminals of VDC OFF switch connector.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace VDC OFF switch. Refer to BRC-146, "
Removal and Installation".
ABS actuator and electric unit (control unit)
—Contin u it y
Connector Terminal
E33 20Ground No
VDC OFF switch
—Continuity
Connector Terminal
M34 2 Ground Yes
VDC OFF switch terminals ConditionContinuity
1 – 2 VDC OFF switch pressed
Yes
VDC OFF switch released No
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 576 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRC-128
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function CheckINFOID:0000000012430909
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combin NISSAN NOTE 2016 Service Repair Manual BRC-128
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function CheckINFOID:0000000012430909
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combin](/manual-img/5/57363/w960_57363-575.png)
BRC-128
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function CheckINFOID:0000000012430909
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for approximately 2 seconds after ignition switch
is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-128, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430910
1.PERFORM THE SELF DIAGNOSTIC
With CONSULT.
Perform “Self Diagnostic Result”.
Are any DTCs detected?
YES >> Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-10, "
METER SYSTEM : Sys-
tem Description" (TYPE A) or MWI-61, "METER SYSTEM : System Description" (TYPE B).
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or MWI-115,
"Removal and Installation" (TYPE B).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 577 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRAKE WARNING LAMPBRC-129
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000012430911
1.CHECK BRAKE WARNING LAMP FUNCTI NISSAN NOTE 2016 Service Repair Manual BRAKE WARNING LAMPBRC-129
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000012430911
1.CHECK BRAKE WARNING LAMP FUNCTI](/manual-img/5/57363/w960_57363-576.png)
BRAKE WARNING LAMPBRC-129
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000012430911
1.CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination mete r turns ON for approximately 2 seconds after ignition
switch is turned ON.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Proceed to diagnosis procedure. Refer to BRC-129, "
Diagnosis Procedure".
2.CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check parking brake switch system. Refer to BRC-124, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430912
1.PERFORM THE SELF DIAGNOSTIC
With CONSULT.
Perform “Self Diagnostic Result”.
Are any DTCs detected?
YES >> Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-10, "
METER SYSTEM : Sys-
tem Description" (TYPE A) or MWI-61, "METER SYSTEM : System Description" (TYPE B).
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or MWI-115,
"Removal and Installation" (TYPE B).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 578 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRC-130
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012430913
1.CHECK VDC OFF INDICA
TOR LAMP FUNCTION
Check that VDC OFF NISSAN NOTE 2016 Service Repair Manual BRC-130
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012430913
1.CHECK VDC OFF INDICA
TOR LAMP FUNCTION
Check that VDC OFF](/manual-img/5/57363/w960_57363-577.png)
BRC-130
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function CheckINFOID:0000000012430913
1.CHECK VDC OFF INDICA
TOR LAMP FUNCTION
Check that VDC OFF indicator lamp in combination meter turns ON for approximately 2 seconds after ignition
switch is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-130, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430914
1.PERFORM THE SELF DIAGNOSTIC
With CONSULT.
Perform “Self Diagnostic Result”.
Are any DTCs detected?
YES >> Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-10, "
METER SYSTEM : Sys-
tem Description" (TYPE A) or MWI-61, "METER SYSTEM : System Description" (TYPE B).
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or MWI-115,
"Removal and Installation" (TYPE B).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 579 of 3641
![NISSAN NOTE 2016 Service Repair Manual SLIP INDICATOR LAMPBRC-131
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000012430915
1.CHECK SLIP INDICATOR LAMP FUN NISSAN NOTE 2016 Service Repair Manual SLIP INDICATOR LAMPBRC-131
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000012430915
1.CHECK SLIP INDICATOR LAMP FUN](/manual-img/5/57363/w960_57363-578.png)
SLIP INDICATOR LAMPBRC-131
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLIP INDICATOR LAMP
Component Function CheckINFOID:0000000012430915
1.CHECK SLIP INDICATOR LAMP FUNCTION
Check that slip indicator lamp in combination meter turns ON for approximately 2 seconds after ignition switch
is turned ON.
Is the inspection result normal?
YES >> Inspection End.
NO >> Proceed to diagnosis procedure. Refer to BRC-131, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430916
1.PERFORM THE SELF DIAGNOSTIC
With CONSULT.
Perform “Self Diagnostic Result”.
Are any DTCs detected?
YES >> Refer to BRC-43, "DTC Index".
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-10, "
METER SYSTEM : Sys-
tem Description" (TYPE A) or MWI-61, "METER SYSTEM : System Description" (TYPE B).
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-54, "
Removal and Installation" (TYPE A) or MWI-115,
"Removal and Installation" (TYPE B).
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 580 of 3641
![NISSAN NOTE 2016 Service Repair Manual BRC-132
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000012430917
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self diagnostic. NISSAN NOTE 2016 Service Repair Manual BRC-132
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000012430917
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self diagnostic.](/manual-img/5/57363/w960_57363-579.png)
BRC-132
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000012430917
If ABS warning lamp and SLIP indicator
lamp turn ON, perform self diagnostic.
NOTE:
• 1: The ABS does not operate when the speed is 10 km/h (6 MPH) or less.
• 2: Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly depressed (just place a foot on it).
However, this is normal:
- When shifting gears
- When driving on slippery road
- During cornering at high speed
- When passing over bumps or grooves [approximately 50 mm (1.97 in) or more]
- When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher] Symptom
Check itemReference
Excessive ABS function operation fre-
quency Brake force distribution
BRC-133, "
Diag-
nosis Procedure"Looseness of front and rear axle
Wheel sensor and rotor system
Unexpected pedal reaction Brake pedal stroke
BRC-134, "
Diag-
nosis Procedure"Make sure the braking force is sufficient when the ABS is not operating.
The braking distance is long Check stopping distance when the ABS is not operating. BRC-135, "
Diag-
nosis Procedure"
ABS function does not operate (Note 1) ABS actuator and electric
unit (control unit)BRC-136, "Diag-
nosis Procedure"
Pedal vibration or ABS operation sound
occurs (Note 2)Brake pedal
BRC-137, "Diag-
nosis Procedure"ABS actuator and electric unit (control unit)
Vehicle jerks during VDC/TCS/ABS con-
trol ABS actuator and electric unit (control unit)
BRC-138, "
Diag-
nosis Procedure"TCM
ECM
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 581 of 3641
![NISSAN NOTE 2016 Service Repair Manual EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-133
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000012 NISSAN NOTE 2016 Service Repair Manual EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-133
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000012](/manual-img/5/57363/w960_57363-580.png)
EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-133
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000012430918
1.CHECK START
Check front and rear brake force di stribution using a brake tester.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles. Refer to front: FA X - 7 , "
Inspection", rear:
RAX-5, "
Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning components.
3.CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following:
• Wheel sensor installation for damage
• Sensor rotor installation for damage
• Wheel sensor connector
• Wheel sensor harness
Is the inspection result normal?
YES >> GO TO 4.
NO >> • Replace wheel sensor BRC-140, "
FRONT WHEEL SENSOR : Removal and Installation" (front)
or BRC-141, "
REAR WHEEL SENSOR : Removal and Installation" (rear).
• Replace sensor rotor BRC-143, "
FRONT SENSOR ROTOR : Removal and Installation" (front)
or BRC-143, "
REAR SENSOR ROTOR : Removal and Installation" (rear).
• Repair harness.
4.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off af ter the ignition switch is turned ON or when driving.
Is the inspection result normal?
YES >> Inspection End.
NO >> Perform “Self Diagnostic Result”. Refer to BRC-31, "
CONSULT Function (ABS)".
Revision: August 2015 2016 Versa Note
cardiagn.com