2016 NISSAN NOTE open hood

DLK-8
HOOD LOCK RELEASE CABLE ............................293
HOOD LOCK RELEASE CABLE : Removal and
Installation .............................................................
293
HOOD LOCK RELEASE HANDLE ........................ ..294
HOOD LOCK RELEASE HANDLE : Removal and
Installation ........................................................... ..
294
FRONT DOOR LOCK ......................................295
Exploded View ..................................................... ..295
DOOR LOCK .......................................................... ..295
DOOR LOCK : Removal and Installation ...............295
INSIDE HANDLE .................................................... ..296
INSIDE HANDLE : Removal and Installation .........296
OUTSIDE HANDLE ................................................ ..297
OUTSIDE HANDLE : Removal and Installation .....297
REAR DOOR LOCK ....................................... .299
Exploded View ..................................................... ..299
DOOR LOCK .......................................................... ..299
DOOR LOCK : Removal and Installation ...............299
INSIDE HANDLE .................................................... ..300
INSIDE HANDLE : Removal and Installation .........300
OUTSIDE HANDLE ................................................ ..301
OUTSIDE HANDLE : Removal and Installation .....301
BACK DOOR LOCK ....................................... .303
Exploded View ..................................................... ..303
BACK DOOR LOCK ............................................... .303
BACK DOOR LOCK : Removal and Installation ...303
OUTSIDE HANDLE ................................................ .303
OUTSIDE HANDLE : Removal and Installation ....303
FUEL FILLER LID OPENER ............................305
Exploded View ..................................................... .305
FUEL FILLER LID .................................................. .305
FUEL FILLER LID : Removal and Installation .......305
FUEL FILLER OPENER CABLE ........................... .306
FUEL FILLER OPENER CABLE : Removal and
Installation .............................................................
306
FUEL FILLER LID LOCK ....................................... .306
FUEL FILLER LID LOCK : Removal and Installa-
tion ........................................................................
307
DOOR SWITCH ................................................308
Removal and Installation .......................................308
REMOTE KEYLESS ENTRY RECEIVER ...... ..309
Removal and Installation .......................................309
KEYFOB BATTERY .........................................310
Removal and Installation .......................................310
STEERING LOCK UNIT ...................................311
Exploded View ..................................................... .311
Removal and Installation - Steering lock unit ........311
Removal and Installation - Ignition switch ............ .312
Revision: August 2015 2016 Versa Note

cardiagn.com

FUEL FILLER LID OPENERDLK-179
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
2. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close and lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and InstallationINFOID:0000000012430136
REMOVAL
1. Remove hood lock/fuel filler lid lock release handle. Refer to DLK-167, "HOOD LOCK RELEASE HAN-
DLE : Removal and Installation".
2. Disconnect fuel filler lid opener cable (2) from hood lock/fuel filler lid lock release handle (1).
3. Remove dash side finisher (LH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
4. Remove center pillar lower finisher (LH). Refer to INT-25, "
CENTER PILLAR LOWER FINISHER :
Removal and Installation".
5. Remove luggage side lower finisher (LH). Refer to INT-34, "
LUGGAGE SIDE LOWER FINISHER :
Removal and Installation".
6. Disconnect fuel filler lid opener cable (1) by pulling downward and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
ALKIA3199ZZ
JMKIA7999ZZ
JMKIA8139ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-306
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
2. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid
assembly open/close and lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and InstallationINFOID:0000000012430282
REMOVAL
1. Remove hood lock/fuel filler lid lock release handle. Refer to DLK-167, "HOOD LOCK RELEASE HAN-
DLE : Removal and Installation".
2. Disconnect fuel filler lid opener cable (2) from hood lock/fuel filler lid lock release handle (1).
3. Remove dash side finisher (LH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
4. Remove center pillar lower finisher (LH). Refer to INT-25, "
CENTER PILLAR LOWER FINISHER :
Removal and Installation".
5. Remove luggage side lower finisher (LH). Refer to INT-34, "
LUGGAGE SIDE LOWER FINISHER :
Removal and Installation".
6. Disconnect fuel filler lid opener cable (1) by pulling downward and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler li d assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
ALKIA3199ZZ
JMKIA7999ZZ
JMKIA8139ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

BASIC INSPECTIONEC-133
< BASIC INSPECTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
BASIC INSPECTION
Work ProcedureINFOID:0000000012431362
1.INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance.
2. Open engine hood and check the following:
- Harness connectors for improper connections
- Wiring harness for improper connections, pinches and cut
- Vacuum hoses for splits, kinks and improper connections
- Hoses and ducts for leaks
- Air cleaner clogging
- Gasket
3. Confirm that electrical or mechanical loads are not applied.
- Headlamp switch is OFF.
- Air conditioner switch is OFF.
- Rear window defogger switch is OFF.
- Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no load.
6. Make sure that no DTC is displayed with CONSULT or GST.
Is any DTC detected?
YES >> GO TO 2.
NO >> GO TO 3.
2.REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3
3.CHECK TARGET IDLE SPEED
1. Run engine at about 2,000 rpm for about 2 minutes under no load.
SEF983U
SEF976U
SEF977U
Revision: August 2015 2016 Versa Note

cardiagn.com

P0111 IAT SENSOREC-195
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0111 IAT SENSOR
DTC LogicINFOID:0000000012431408
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Is it necessary to erase permanent DTC?
YES >> GO TO 3.
NO >> GO TO 2.
2.PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to EC-196, "
Component Function Check".
NOTE:
Use the component function check to check the overall func tion of the IAT sensor circuit. During this check, a
1st trip DTC might not be confirmed.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-196, "
Diagnosis Procedure".
3.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following proce-
dure before conducti ng the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
• Before performing the following procedure, do not add fuel.
• Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
• Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 60 minutes.
2. Move the vehicle to a cool place. NOTE:
Cool the vehicle in an environment of ambient air temperature between −10° C (14 °F) and 35 °C (95° F).
3. Turn ignition switch OFF and soak the vehicle for 12 hours. CAUTION:
Never turn ignition sw itch ON during soaking.
NOTE:
The vehicle must be cooled with the hood open.
4. Start engine and let it idle for 5 minutes or more. CAUTION:
Never turn ignition swit ch OFF during idling.
5. Check 1st trip DTC.
DTC No. CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P 0 111 IAT SENSOR 1 B1
[Intake air temperature (IAT) sen-
sor circuit range/performance] The comparison result of signals transmitted to ECM
from each temperature sensor (IAT sensor, ECT sensor,
FTT sensor, and EOT sensor) sh
ows that the voltage sig-
nal of the IAT sensor is higher/lower than that of other
temperature sensors when the engine is started with its
cold state. • Harness or connectors
(High or low resistance in
the IAT sensor circuit)
• IAT sensor
Revision: August 2015 2016 Versa Note

cardiagn.com

P0116 ECT SENSOREC-199
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0116 ECT SENSOR
DTC LogicINFOID:0000000012431415
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Is it necessary to erase permanent DTC?
YES >> GO TO 3.
NO >> GO TO 2.
2.PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to EC-200, "
Component Function Check".
NOTE:
Use the component function check to check the overall function of the ECT sensor circuit. During this check, a
1st trip DTC might not be confirmed.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-200, "
Diagnosis Procedure".
3.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following proce-
dure before conducti ng the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
• Before performing the following procedure, do not add fuel.
• Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
• Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 60 minutes.
2. Move the vehicle to a cool place. NOTE:
Cool the vehicle in an environment of ambient air temperature between −10° C (14 °F) and 35 °C (95° F).
3. Turn ignition switch OFF and soak the vehicle for 12 hours.
CAUTION:
Never turn ignition sw itch ON during soaking.
NOTE:
The vehicle must be cooled with the hood open.
4. Start engine and let it idle for 5 minutes or more. CAUTION:
Never turn ignition swit ch OFF during idling.
DTC No.CONSULT screen terms
(Trouble diagnosis content) DTC detecting condition
Possible cause
P0116 ECT SEN/CIRC
[Engine coolant temperature
(ECT) sensor circuit range/per-
formance] The comparison result of signals transmitted
to ECM from each temperature sensor (IAT
sensor, ECT sensor, FTT sensor, and EOT
sensor) shows that the voltage signal of the
ECT sensor is higher/lower than that of other
temperature sensors when the engine is
started with its cold state. • Harness or connectors
(High or low resistance in the ECT
sensor circuit)
• ECT sensor
Revision: August 2015 2016 Versa Note

cardiagn.com

P0137 HO2S2EC-223
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0137 HO2S2
DTC LogicINFOID:0000000012431441
DTC DETECTION LOGIC
The heated oxygen sensor 2 has a much longer switching time
between rich and lean than the air fuel
ratio (A/F) sensor 1. The oxy-
gen storage capacity of the three way catalyst 1 causes the longer
switching time. To judge the malfunctions of heated oxygen sensor
2, ECM monitors whether the maximum voltage of the sensor is suf-
ficiently high during various driving conditions such as fuel-cut.
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO >> GO TO 5.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
For better results, perform “DTC WORK SUPPORT” at a temperature of 0 to 30 °C (32 to 86 °F).
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON and select “DATA MONITOR” mode of “ENGINE” using CONSULT.
2. Start engine and warm it up to normal operating temperature.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
5. Let engine idle for 1 minute.
6. Make sure that “COOLAN TEMP/S” indicates more than 70 °C (158° F).
If not, warm up engine and go to next step w hen “COOLAN TEMP/S” indication reaches 70 °C (158° F).
7. Open engine hood.
8. Select “HO2S2 (B1) P1147” of “HO2S2” in “DTC WORK SUPPORT” mode of “ENGINE” using CONSULT.
9. Follow the instruction of CONSULT.
NOTE:
It will take at most 10 minutes until “COMPLETED” is displayed.
:0.75 V
JSBIA4446GB
DTC No. Trouble diagnosis content DTC detecting conditionPossible cause
P0137 Heated oxygen sensor 2
circuit low voltage The maximum voltage from the sensor does
not reach the specified voltage. • Harness or connectors
(The sensor circuit is open or shorted)
• Heated oxygen sensor 2
• Fuel pressure
• Fuel injector
• Intake air leaks
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-230
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0138 HO2S2
3. Start engine and keep the engine speed between 3,500 and
4,000 rpm for at least 1 minute under no load.
4. Let engine idle for 2 minutes.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-231, "Diagnosis Procedure".
NO-1 >> With CONSULT: GO TO 3.
NO-2 >> Without CONSULT: GO TO 5.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
NOTE:
For better results, perform “DTC WORK SU PPORT” at a temperature of 0 to 30°C (32 to 86°F).
1. Turn ignition switch ON and select “DATA MONITOR” mode of “ENGINE” using CONSULT.
2. Start engine and warm it up to normal operating temperature.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
5. Let engine idle for 1 minute.
6. Make sure that “COOLAN TEMP/S” indication is more than 70 °C (158° F).
If not, warm up engine and go to next step when “COOLAN TEMP/S” indication reaches 70°C (158° F).
7. Open engine hood.
8. Select “HO2S2 (B1) P1146” of “HO2S2” in “DTC WORK SUPPORT” mode of “ENGINE” using CONSULT.
9. Follow the instruction of CONSULT. NOTE:
It will take at most 10 minutes until “COMPLETED” is displayed.
10. Touch “SELF-DIAG RESULT”.
Which is displayed on CONSULT
OK >> INSPECTION END
NG >> Proceed to EC-231, "
Diagnosis Procedure".
CAN NOT BE DIAGNOSED>>GO TO 4.
4.PERFORM DTC CONFIRMATION PROC EDURE FOR MALFUNCTION B AGAIN
1. Turn ignition switch OFF and leave the vehi cle in a cool place (soak the vehicle).
2. Perform DTC confirmation procedure again.
>> GO TO 3.
5.PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B
Perform component function check. Refer to EC-230, "
Component Function Check".
NOTE:
Use component function check to check the overall function of the heated oxygen sensor 2 circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-231, "
Diagnosis Procedure".
Component Function CheckINFOID:0000000012431446
1.PERFORM COMPONENT FUNCTION CHECK-I
Without CONSULT
1. Start engine and warm it up to the normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
6. Let engine idle for 1 minute.
7. Check the voltage between ECM harness connector terminals under the following condition.
Revision: August 2015 2016 Versa Note

cardiagn.com