2016 NISSAN NOTE turn signal

SYSTEM (POWER DOOR LOCK SYSTEM)DLK-21
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Setting change of Automatic Door Locks (LOCK) Function
The LOCK operation setting of the aut
omatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (LOCK) function and the type selection of the automatic
door locks (LOCK) function can be performed at the “Work support” setting. Refer to BCS-18, "
DOOR LOCK :
CONSULT Function (BCM - DOOR LOCK)".
Without CONSULT
The automatic door locks (LOCK) function can be switched ON/OFF by performing the following operation:
1. Close all doors. (door switch OFF)
2. Push the ignition switch to the ON position.
3. Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec- onds after turning the ignition switch ON.
4. The switching is completed when the hazard lamp blinks.
5. The ignition switch must be turned OFF and ON again between each setting change.
AUTOMATIC DOOR LOCKS (UNLOCK OPERATION)
The automatic door locks (UNLOCK) function is the func tion that unlocks all doors linked with the key position
or shift position.
IGN OFF Interlo ck Door Unlock*1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuator s when it detects that the power supply position is
changed from ignition switch ON to OFF.
Setting change of Automatic Door Locks (UNLOCK) Function
The UNLOCK operation setting of the automatic door locks function can be changed.
With CONSULT
The ON/OFF switching of the automatic door locks (UNL OCK) function and the type selection of the automatic
door locks (UNLOCK) function can be performed at the “Work support” setting. Refer to BCS-18, "
DOOR
LOCK : CONSULT Function (BCM - DOOR LOCK)".
Without CONSULT
The automatic door locks (UNLOCK) function can be sw itched ON/OFF by performing the following operation:
1. Close all doors. (door switch OFF)
2. Place the ignition switch in the ON position.
3. Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20 seconds after turning the power supply position ON.
4. The switching is completed when the hazard lamp blinks.
5. The ignition switch must be turned OFF and ON again between each setting change.
*1: This function is set to ON before delivery.
OFF → ON : 2 blinks
ON → OFF : 1 blink
OFF → ON : 2 blinks
ON → OFF : 1 blink
Revision: August 2015 2016 Versa Note

cardiagn.com

SYSTEM (INTELLIGENT KEY SYSTEM)DLK-23
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK FUNCTION
DOOR LOCK FUNCTION : System DescriptionINFOID:0000000012429984
SYSTEM DIAGRAM
DOOR REQUEST SWITCH OPERATION
When pressing the request switch, it is possible to lock and unlock the door by carrying the Intelligent Key.
OPERATION DESCRIPTION
• When the BCM detects that each door request switch is pressed, it starts the outside key antenna and inside
key antenna corresponding to the pressed door request swit ch and transmits the request signal to the Intelli-
gent Key. And then, check that the Intelligent Key is near the door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM transmits door lock/unlock signal and operates each door lock actuator. At the same time, BCM blinks
hazard warning lamp (lock: 2 times, unlock: 1 time) and sounds Intelligent Key buzzer (lock: 1 time, unlock:
1 time) as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unl ock operation is performed if the door request switch is
operated:
Key reminder The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle. DLK-27
WarningIf an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver.
DLK-27
Engine start
The engine can be turned on while carrying the Intelligent Key. DLK-22
Interior room lamp control Interior room lamp is controlled according to door lock/unlock state. DLK-20
FunctionDescriptionRefer
JMKIA6137GB
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-30
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Fu
nction (BCM - COMMON ITEM)INFOID:0000000012542542
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode Description
ECU Identification The BCM part number is displayed.
Self Diagnostic Result The BCM self diagnostic results are displayed.
Data Monitor The BCM input/output data is displayed in real time.
Active Test The BCM activates outputs to test components.
Work support The settings for BCM functions can be changed.
Configuration • The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed.
System Sub System Direct Diagnostic Mode
ECU Identification
Self Diagnostic Result
Data Monitor
Active Test
Work support
Configuration
CAN DIAG SUPPORT MNTR
Door lock
DOOR LOCK ×××
Rear window defogger REAR DEFOGGER ××
Warning chime BUZZER ××
Interior room lamp timer INT LAMP ×××
Exterior lamp HEAD LAMP ×××
Wiper and washer WIPER ×××
Turn signal and hazard warning lamps FLASHER ×××
Air conditioner AIR CONDITIONER ×
Intelligent Key system INTELLIGENT KEY ××××
Combination switch COMB SW ×
BCM BCM× × ×××
Immobilizer IMMU ××××
Interior room lamp battery saver BATTERY SAVER ×××
Vehicle security system THEFT ALM ××
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR ××××
Panic alarm system PANIC ALARM ×
Revision: August 2015 2016 Versa Note

cardiagn.com

B2621 INSIDE ANTENNADLK-65
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DTC/CIRCUIT DIAGNOSIS
B2621 INSIDE ANTENNA
DTC LogicINFOID:0000000012429997
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE ANT DIAG NOSIS” in “Work support”.
3. Perform inside key antenna “INSIDE ANT DIAGNOSIS”.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES >> Refer to DLK-65, "Diagnosis Procedure".
NO >> Inside key antenna (instrument center) is OK.
Diagnosis ProcedureINFOID:0000000012429998
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
DTCCONSULT display
description DTC detecting condition
Possible cause
B2621 INSIDE ANTENNA 1 An excessive high or low voltage from inside anten-
na (instrument center) is sent to BCM. • Inside key antenna (instrument
center)
• Between BCM Inside key antenna (instrument center)
(+)
(–)Condition Signal
(Reference value)
BCM
Connector Terminal
M98 84
85GroundWhen Intelligent Key is in the an-
tenna detection area.
When Intelligent Key is not in the
antenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note

cardiagn.com

DLK-66
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2621 INSIDE ANTENNA
NO >> GO TO 2.
2.CHECK INSIDE KEY ANTENNA CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and inside key antenna (instrument center) connector.
3. Check continuity between BCM harness connector and inside key antenna (instrument center) harness
connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace inside key antenna (instrument center). (New antenna or other antenna)
2. Connect BCM connector and inside key antenna (instrument center) connector.
3. Turn ignition switch ON.
4. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace inside key antenna (instrument center). Refer to DLK-182, "INSTRUMENT CENTER :
Removal and Installation".
NO >> Replace BCM. Refer to BCS-74, "
Removal and Installation".
BCM Inside key antenna (instrument center)
Continuity
Connector TerminalConnector Terminal
M98 84
M95 1
Ye s
85 2
BCM GroundContinuity
Connector Terminal
M98 84
No
85
(+)
(–)Condition Signal
(Reference value)
BCM
Connector Terminal
M98 84
85GroundWhen Intelligent Key is in the an-
tenna detection area.
When Intelligent Key is not in the
antenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note

cardiagn.com

B2622 INSIDE ANTENNADLK-67
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2622 INSIDE ANTENNA
DTC LogicINFOID:0000000012429999
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE ANT DIAG NOSIS” in “Work support”.
3. Perform “INSIDE ANT DIAGNOSIS”.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES >> Refer to DLK-67, "Diagnosis Procedure".
NO >> Inside key antenna (console) is OK.
Diagnosis ProcedureINFOID:0000000012430000
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK INSIDE KEY ANTENNA CIRCUIT
DTC CONSULT display
description DTC detecting condition
Possible cause
B2622 INSIDE ANTENNA 2 An excessive high or low voltage from inside anten-
na (console) is sent to BCM. • Inside key antenna (console)
• Between BCM Inside key antenna
(console)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 86
87GroundWhen Intelligent Key is in the anten-
na detection area.
When Intelligent Key is not in the an-
tenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note

cardiagn.com

DLK-68
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2622 INSIDE ANTENNA
1. Turn ignition switch OFF.
2. Disconnect BCM connector and inside key antenna (console) connector.
3. Check continuity between BCM harness connector and inside key antenna (console) harness connector.
4. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace inside key antenna (console). (New antenna or other antenna)
2. Connect BCM connector and inside key antenna (console) connector.
3. Turn ignition switch ON.
4. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace inside key antenna (console). Refer to DLK-182, "CONSOLE : Removal and Installation".
NO >> Replace BCM. Refer to BCS-74, "
Removal and Installation".
BCM Inside key antenna (console)
Continuity
Connector TerminalConnector Terminal
M98 86
M89 1
Ye s
87 2
BCM GroundContinuity
Connector Terminal
M98 86
No
87
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 86
87GroundWhen Intelligent Key is in the anten-
na detection area.
When Intelligent Key is not in the an-
tenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note

cardiagn.com

B2623 INSIDE ANTENNADLK-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
B2623 INSIDE ANTENNA
DTC LogicINFOID:0000000012430001
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE ANT DIAG NOSIS” in “Work support”.
3. Perform “INSIDE ANT DIAGNOSIS”.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES >> Refer to DLK-69, "Diagnosis Procedure".
NO >> Inside key antenna (trunk room) is OK.
Diagnosis ProcedureINFOID:0000000012430002
Regarding Wiring Diagram information, refer to DLK-46, "Wiring Diagram".
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch ON.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-74, "Removal and Installation".
NO >> GO TO 2.
2.CHECK INSIDE KEY ANTENNA CIRCUIT
DTC CONSULT display
description DTC detecting condition
Possible cause
B2623 INSIDE ANTENNA 3 An excessive high or low voltage from inside anten-
na (trunk room)
is sent to BCM. • Inside key antenna (trunk room)
• Between BCM Inside key antenna
(trunk room)
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M98 88
89GroundWhen Intelligent Key is in the anten-
na detection area.
When Intelligent Key is not in the an-
tenna detection area.
JMKIA3839GB
JMKIA5951GB
Revision: August 2015
2016 Versa Note

cardiagn.com