2016 Citroen BERLINGO MULTISPACE RHD Owner's Manual

15
Motoring & the Environment
Berlingo-2-VP_en_Chap02_eco-conduite_ed02-2015
ENVIRONMENT
With you, CITRoËn acts to protect the
environment.
W
e invite you to visit the
www.citroen.co.uk
  website.a s the driver, you also can contribute
to   protecting   the   environment   in   the  
following

  way:
-
 
drive
  smoothly,   without   frequent  
and harsh acceleration,
-


observe the service intervals;
we

  recommend   that   services   are  
carried out by a CITR

o Ë n dealer,
authorised to collect used batteries
and
  fluids,
-

in order to preserve the reliability
of

  the   engine   and   emission   control  
systems,

  do   not   use   engine   oil  
additives.Refer

  to   information   on   eco-driving  at
  the   end   of   this   section.
2
ECo-dRIVInG

16
Motoring & the Environment
Berlingo-2-VP_en_Chap02_eco-conduite_ed02-2015
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and Co
2 emissions.
Eco-driving
Optimise the use of your gearbox
With a manual gearbox, move off gently and change up without   waiting.   During   acceleration   change   up   early.
With
  an   automatic   or   electronic   gearbox,   give   preference  
to

  automatic   mode   and   avoid   pressing   the   accelerator  
pedal

  heavily   or   suddenly.
The
  gear   shift   indicator   invites   you   engage   the   most  
suitable

  gear:   as   soon   as   the   indication   is   displayed   in   the  
instrument

  panel,   follow   it   straight   away.
For
  vehicles   fitted   with   an   electronic   or   automatic   gearbox,  
this

  indicator   appears   only   in   manual   mode.
Drive smoothly
Maintain a safe distance between vehicles, use engine
braking  rather   than   the   brake   pedal,   and   press   the  
accelerator

  progressively.  
These
  practices   contribute  
towards

 
a
 
reduction
 
in
 
fuel
 
consumption
 
and
 
CO2 emissions and
 
also
 
helps
 
reduce
 
the
 
background
 
traffic
 
noise.
If your vehicle has cruise control, make use of the system at   speeds   above   25   mph   (40   km/h)   when   the   traffic   is  
flowing

  well.
Control the use of your electrical
equipment
Before moving off, if the passenger compartment is too warm,  ventilate   it   by   opening   the   windows   and   air   vents  
before

  using   the   air   conditioning.
Above
  30   mph   (50   km/h),   close   the   windows   and   leave   the  
air

  vents   open.
Remember
  to   make   use   of   equipment   that   can   help   keep  
the

  temperature   in   the   passenger   compartment   down  
(sunroof

  and   window   blinds...).
Switch
  off   the   air   conditioning,   unless   it   has   automatic  
regulation,

  as   soon   as   the   desired   temperature   is   attained.
Switch
  off   the   demisting   and   defrosting   controls,   if   not  
automatic.
Switch

  off   the   heated   seat   as   soon   as   possible.
Switch
  off   the   headlamps   and   front   foglamps   when   the  
level

  of   light   does   not   require   their   use.
Avoid
  running   the   engine   before   moving   off,   particularly   in  
winter;

  your   vehicle   will   warm   up   much   faster   while   driving.
As
  a   passenger,   if   you   avoid   connecting   your   multimedia  
devices

  (film,   music,   video   game...),   you   will   contribute  
towards

  limiting   the   consumption   of   electrical   energy,   and  
so

  of   fuel.
Disconnect
  your   portable   devices   before   leaving   the   vehicle.

17
Motoring & the Environment
Berlingo-2-VP_en_Chap02_eco-conduite_ed02-2015
Limit the causes of excess consumption
Spread loads throughout the vehicle; place the heaviest
items  in   the   bottom   of   the   boot,   as   close   as   possible   to   the  
rear

  seats.
Limit
  the   loads   carried   in   the   vehicle   and   reduce   wind  
resistance

  (roof   bars,   roof   rack,   bicycle   carrier,   trailer...).  
Use

  a   roof   box   in   preference.
Remove
  roof   bars   and   roof   racks   after   use.
At
  the   end   of   winter,   remove   snow   tyres   and   refit   your  
summer

  tyres.
Observe the recommendations on maintenance
Check the tyre pressures regularly, when cold, referring to the  label   in   the   door   aperture,   driver's   side.
Carry
  out   this   check   in   particular:
-
 
before
  a   long   journey,
-

at each change of season,
-

 
after
  a   long   period   out   of   use.
d

on't forget the spare wheel and the tyres on any trailer or
caravan.
Have your vehicle serviced regularly (engine oil, oil
filter,
  air   filter,   passenger   compartment   filter...)   and  
observe

  the   schedule   of   operations   recommended   in   the  
manufacturer's

  service   schedule.
With
  a   BlueHDi   Diesel   engine,   if   the   SCR   system   is  
faulty

  your   vehicle   becomes   polluting;   go   to   a   CITROËN  
dealer

  or   a   qualified   workshop   without   delay   to   have   the  
emissions

  of   nitrous   oxides   brought   back   to   the   legal   level.
When refuelling, do not continue after the third cut-off of
the
  nozzle   to   avoid   any   overflow.
At
  the   wheel   of   your   new   vehicle,   it   is   only   after   the   first  
1

  800   miles   (3   000   kilometres)   that   you   will   see   the   fuel  
consumption

  settle   down   to   a   consistent   average.
2
ECO-DRIVING

18
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
This locks and unlocks the vehicle's doors,  opens   and   closes   the   fuel   filler  
cap, as well as starting and stopping
the

  engine.
KEYR EMOTE CONTROL
Unlocking
Locking
Press this button to lock all of your
  vehicle's   doors.
The
 
direction   indicators   flash   once.
If one of the doors is open or is not
closed
 
correctly,   the   central   locking   will  
not

 
work.
Deadlocking
A second press on the closed
padlock   on   the   remote   control   within  
five seconds

  after   locking   changes   the  
locking

  to   deadlocking.
This
  is   confirmed   by   fixed   lighting  
of the direction indicators for
approximately

  two   seconds.
Deadlocking
  renders   the   exterior  
and interior door opening handles
inoperative:

  do   not   leave   anyone   inside  
the

  vehicle   when   it   is   deadlocked.
If
  deadlocking   is   activated   from   inside  
the

  vehicle   using   the   remote   control,   it  
will

  change   to   normal   locking   when   the  
vehicle

  is   started.
Press
 
this
 
button
 
to
 
unlock
 
all
 of
 
your
 
vehicle's
 
doors.
The
 
direction
 
indicators
 
flash
 
twice.
access

19
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Good practice
Take care not to allow the remote control  to   come   into   contact   with  
grease,

  dust,   rain   or   a   damp  
environment.
A
 

heavy   object   attached   to   the   key  
(key

  ring,   ...)   weighing   on   the   shaft  
of

  the   key   in   the   switch,   may   cause   a  
malfunction.
REMOTE CONTROL
Reinitialising the remote control
Following changing of the remote control battery or disconnection of the
vehicle  battery,   the   remote   control   may  
have

  to   be   reinitialised.
Wait
  at   least   one   minute   before   using  
the

  remote   control.
Insert
  the   key   in   the   ignition   switch   with  
the

  buttons   (padlocks)   of   the   remote  
control

  facing   you.
Switch
  on   the   ignition.
Press
  the   locking   padlock   for   at  
least

  five   seconds   within   the   next  
ten seconds.
Switch

  off   the   ignition.
Wait
  at   least   one   minute   before   using  
the

  remote   control.
The
  remote   control   is   now   working  
again.
Use only identical batteries or
batteries of an equivalent type to
those

 
recommended
 
by
 
CITROËN
 
dealers.
Do

 
not
 
discard
 
the
 
remote
 
control
 
batteries,

 
they
 
contain
 
metals
 
which
 
are

 
harmful
 
to
 
the
 
environment.
Deposit
 
them
 
at
 
a
 
CITROËN
 
dealership, or at an authorised
collection

 
point.
Unfolding / folding
Changing the battery
Battery ref.: CR1620 / 3 volts.
The   "battery   flat"   information   is   given  
by

  an   audible   signal,   accompanied   by  
a

  message   in   the   screen.
To replace the battery, unclip the
casing
  using   a   coin   at   the   ring.
If
  the   remote   control   does   not   work  
after the battery has been changed,
reinitialise

  the   remote   control.
There
  is   a   risk   of   damage   if   the  
replacement

  battery   is   not   the   correct  
type.If you do not press the button,
you

  may   damage   the   key's  
folding

  mechanism.
access
REadY To Go
3

20
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Don't forget
When  leaving   the   vehicle,   check   that  
the lighting is of

f and nothing of value
is
  visible.
a

s a safety precaution (with children
on
  board),   remove   the   key   from   the  
ignition when leaving the vehicle, even
for

  a   short   time.
Good practice
Do not make any modifications to the electronic  immobiliser   system.
Operating
  the   remote   control,   even  
when

  it   is   in   your   pocket,   may   result   in  
involuntary

  unlocking   of   the   doors.
The
  simultaneous   use   of   other  
high

  frequency   equipment   (mobile  
telephones,

  domestic   alarms…),   may  
interfere with the operation of the
remote

  control   temporarily.
The
  remote   control   does   not   operate  
while

  the   key   is   in   the   ignition,   even   if  
the

  ignition   is   off.
ELECTRONIC
IMMOBILISER
If you lose your keys
Visit a CITRo Ë n dealer with the
vehicle's
  V5   registration   certificate   and  
your

  identification   document.
a CITR

o Ë n dealer will be able
to
  retrieve   the   key   code   and  
the transponder code so that a
replacement

  key   can   be   ordered.When purchasing a second-hand
vehicle,
  have   the   keys   memorised   by  
a CITR

o Ë n dealer, so as to be sure
that   the   keys   in   your   possession   are  
the only ones that can be used to start
the

  vehicle.
ALARM
If fitted on your vehicle, this provides two
  types   of   protection:
-
 
exterior
  protection:   it   sounds   if   a  
front/rear

  door   or   the   bonnet   is  
opened.
-

 
interior
  protection:   it   sounds   if  
the

  volume   inside   the   passenger  
compartment

  changes   (breaking   of  
a

  window   or   a   movement   inside   the  
vehicle).
If

 
your
 
vehicle
 
is
 
fitted
 
with
 
a
 
separation
 
partition, the interior protection is not
active

  in   the   load   space.
Locking the vehicle with
complete alarm
Setting the alarm
- Switch off the ignition and get out of
the   vehicle.
-
 
Set
  the   alarm   within   five   minutes   of  
getting

  out   of   the   vehicle,   by   locking  
or

  deadlocking   using   the   remote  
control.

 
The
  red   LED,   located   in   the  
button,

  flashes   once   per   second.
All of the keys contain an electronic immobiliser  device.
This
  device   locks   the   engine   supply  
system.

  It   is   activated   automatically  
when

  the   key   is   removed   from   the  
ignition.
a

fter the ignition is switched on, a
dialogue
  is   established   between   the   key  
and

  the   electronic   immobiliser   system.
The
  metal   part   of   the   key   must   be  
unfolded correctly for correct dialogue
to

  take   place.
access

21
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
FRONT DOORS
From the inside
Use the door opening control to unlock and  open   the   door   concerned.
From the outside
Use the remote control to lock/unlock the  vehicle.
Insert
  the   metal   part   of   the   key   in   the  
lock

  on   the   driver's   side   if   the   remote  
control

  does   not   work.
Disarming
- Unlock  the   vehicle   with   the   remote  control or switch on the ignition, the
red
  LED   goes   off.
Locking the vehicle with
exterior protection only
If, while you are away from the vehicle, you wish to leave a window partially
open or a pet inside the vehicle, you
should
  choose   exterior   protection   only.
-
 
Switch
  off   the   ignition.
-

In the next ten seconds,
press the button until the
red 
LED
 
is
 
on
 
continuously
.
- Get  out   of   the   vehicle.
-  
Within
  the   next   five   minutes,   set  
the

  alarm   by   locking   or   deadlocking  
using

  the   remote   control   (the   red  
LED

  flashes   once   a   second).
Triggering
The siren sounds, the direction indicators
flash  for   approximately   30   seconds   and  
the

  red   LED   flashes   rapidly.
- To switch it off, insert the key and switch  on   the   ignition.
When
  the   alarm   has   been   triggered   ten  
times

 
in
 
succession
 
(when
 
triggered
 
for
 
the
 
eleventh

  time)   it   is   deactivated.   Repeat   the  
procedure

  for   setting   the   alarm.
Locking the vehicle without
alarm
- Insert  the   key   in   the   lock   on   the  driver's
  door   and   lock   it.
Do
  not   set   the   alarm   when   washing  
your

  vehicle.
Failure of the remote control
When the alarm is set but the remote control   does   not   operate:
-

Unlock the doors with the key and open   the   door.  The   alarm   is   triggered.
- Switch on the ignition in the
next  ten   seconds.  The   alarm   is  
disarmed.
Incorrect operation
When the ignition is switched on, if the
red  LED   remains   on   for   ten   seconds,  
there

  is   a   fault   in   the   siren   connection.
Contact a CITR
o Ë n dealer to have the
system
  checked.
Automatic setting of the alarm
depending on the country in which
the   vehicle   is   sold,   the   alarm   is   set  
automatically

  approximately   2   minutes  
after

  the   last   door   is   closed.
To
  prevent   triggering   of   the   alarm   when  
a door is opened, you have to press
the

  remote   control   unlocking   button  
again.Do

  not   make   any   modifications  
to

  the   alarm   system   as   this   could  
cause

  faults.
access
REadY To Go
3

22
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
SLIDING SIDE DOORS
From the outside
Pull the handle towards you then
towards the rear and open the side
door guiding the rearward sliding to
beyond the point of resistance to hold
it  open.
A
 

mechanical   system   prevents   opening  
of the left-hand side door when the fuel
filler

  flap   is   open.
From the inside
Unlock the side door using this handle and open it, guiding the rearward
sliding  to   the   point   of   resistance.   Pass  
this

  point   to   hold   the   door   open.
Close the side door using the handle
to start the sliding and pass the point
of
  resistance.  
Then,
  use   the   shaped  
recess at the top of the door pilla

r to
guide
  the   door   until   it   locks.
d

o not use the grab handle to slide the
door.
Good practice
Take care not to block the guide space on   the   floor   to   allow   the   door   to   slide  
correctly

.
If
  your   vehicle   is   parked   on   a   slope,  
guide

  the   sliding   of   the   side   door.   In  
fact,

  the   door   could   open   or   close   more  
rapidly due to the slope of the ground
and

  could   cause   injury.
For safety and operation reasons, do
not drive with the sliding side doors
open.
access