2016 Citroen BERLINGO MULTISPACE RHD Owner's Manual

 167
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
AdBlue® additive
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Fault confirmed
In addition to the previous signals,
the  UREA
 
warning   lamp   flashes   and  
the

  remaining   range   allowed   will   be  
displayed

  in   miles   (kilometres).
The alert will be repeated every
30
seconds with an update of the
driving
  range   in   steps   of   30   miles  
(50 km).
Go

  to   a   CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
You
  risk   not   being   able   to   start   the  
engine.
Starting prevented, having
covered the 650 miles (1 100 km)
At

  each   attempt   at   starting,   the   alert   is  
activated

  and   the   message   "Emissions  
fault:

  Starting   prevented"   is   displayed.Refilling / Topping-up the
AdBlue® additive
Precautions to take
Use only a dBlue® additive that meets the
 
ISO
 
22241
 
standard.
The
a
dBlue
® additive is an urea-based
solution.
This
 
liquid

 
is

 
non-flammable,
 
colourless
 
and

 
odourless.
To
 
be
 
kept
 
in   a   cool   area.
Containers (5 or 10 litres) and
bottles (1.89 litres) of AdBlue
®
Please check the use-by date.
Read   the   instructions   on   the   label.
Ensure that you have a suitable
filler
  pipe,   which   may   or   may   not   be  
supplied

  with   the   container. In
  the   event   of   an   overflow,   wipe  
around

  the   filler   mouth   using   a  
damp

  cloth.
If any a dBlue
® fluid is split or splashed on
 
to
 
you,
 
wash   immediately   with   cold  
water or wipe yourself with a clean
damp

 
cloth.
If the additive has crystallised, clean it
off
 
using
 
a
 
sponge   and   hot   water.
CHECKS
7

168
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
AdBlue® additive
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Filling
Ensure that the vehicle is parked on a flat  and   level   surface.
Pour
  the   contents   of   the   container   /  
bottle

  into   the   dedicated   tank.
After
  filling   the   additive   tank,   observe  
the

  following   procedure:
-

Switch on the ignition without
starting.
-


W
ait 10 seconds before starting the
engine.
Never
  dispose   of   empty  
AdBlue®
containers and bottles in the
household
 
waste.
Place
 
them
 
in
 
a
 
special
 
container
 
provided

 
this
 
purpose
 
or
 
take
 
them
 
to  
your

 
dealer.
k
eep a dBlue
® out of the reach of
children,
 
in
 
its
  original   container.
n

ever transfer
a
dBlue
® to another
container:
 
it
 
would
 
loose   its   purity.
Never
 
dilute
 
the
 
additive   with   water.
n

ever pour the additive into the d iesel
fuel
 
tank.
Recommendations on storage
never store containers or bottles of a dBlue® in your vehicle.
Freezing of the AdBlue
® additive
a

dBlue® freezes at about -11°C (12.2°F)
  and   deteriorates   above   25°C  
(77°F).
It

 
is
 
recommended   that   containers   and  
bottles be stored in a cool area and
protected

  from   direct   sunlight.
Under these conditions, the additive
can
 
be
 
kept   for   at   least   a   year.
a

dditive that has been frozen can be
used
 
once   it   has   thawed   out   in   ambient  
air

. The
  SCR   system   includes   an  
a dBlue
® tank heater that ensures operation
  of   the   vehicle   in   normal  
conditions.
In exceptional situations, such as when
the

 
vehicle
 
is   kept   at   temperatures  
below

 
-15°C
  (5°F)   for   a   long   period,  
there

 
may
 
be   an   emission   fault   alert  
related to freezing of the a

dBlue
®
additive.
Park
 
the
 
vehicle
 
in
 
an
 
area
 
at
 
a
 
more  
moderate

 
temperature
 
for
 
a
 
few
 
hours  
until

 
the
 
additive
 
becomes
 
a
 
liquid  
again.
The

 
emissions
 
warning
 
lamp
 
does   not  
go

 
off
 
immediately,
 
but
 
does
 
so
 
after   a  
few

 
miles
 
of
 
driving.

169
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
BATTERY
Before disconnecting the battery, you
must  wait   for   2   minutes   after   switching  
of

f   the   ignition.
Never
  disconnect   a   terminal   when   the  
engine

  is   running.
Never
  charge   a   battery   without   first  
disconnecting

  the   terminals.
a

fter every reconnection of the battery,
switch
  on   the   ignition   and   wait   1   minute  
before starting to allow the electronic
systems

  to   be   initialised.   If   problems  
remain

  after   doing   this,   please   contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
a

fter changing bulbs, wait
approximately
  3   minutes   before  
reconnecting

  the   battery.
It is advisable to disconnect the
battery if the vehicle is not to be
used

 
for
 
a
 
period
 
of
 
more
 
than
 
one month.
To charge the battery using a
battery charger
- Disconnect   the   battery.
-
Follow the instructions for use
given by the battery charger
manufacturer

.
-

Reconnect starting with the
negative

  (-)   terminal.
-
 
Check
  that   the   terminals   and  
connectors

  are   clean.   If   they   are  
covered with sulphate (white or
greenish

  deposit),   disconnect   them  
and

  clean   them.
To start the vehicle from
another battery
- Connect the red cable to the
positive  (+)   terminals   of   the  
two batteries.
-


Connect one end of the green
or

  black   cable   to   the   negative   (-)  
terminal

  of   the   slave   battery.
-

Connect the other end of the green
or

  black   cable   to   an   earth   point   on  
the

  broken   down   vehicle   as   far   as  
possible

  from   the   battery.
-
 Operate

  the   starter,   let   the   engine   run.
-

W
ait for the engine to return to idle,
then
  disconnect   the   cables.
The presence of this label
indicates the use of a 12 V
lead-acid battery with special
technology
 
and
 
specification,
 
for
 
which
 
the

 
involvement
 
of
 
a
 
CITROËN
 
dealer
 
or

 
qualified
 
workshop
 
is
 
required
 
when
 
replacing

 
or
 
disconnecting
 
the
 
battery.
Failure to observe this
recommendation
 
may
 
cause
 
premature
 wear
 
of
 
the
 
battery.
After
 
refitting
 
the
 
battery,
 
the
 
Stop &
 
Start

 
system
 
will
 
only
 
be
 
active
 
after
 
several hours depending on the
climatic

 
conditions
 
and
 
the
 
state
 
of
 
charge of the battery (up to about
8 hours).
The Stop & Start battery does not have
to

 
be
 
disconnected
 
for
 
charging.
Battery
QUICk HELP
8

170
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
ECONOMY MODE
after the engine has stopped, with
the   key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows,
  courtesy   lamps,   audio  
equipment,

  etc.)   can   only   be   used   for   a  
cumulative

  duration   of   thirty   minutes,   to  
prevent

  discharging   of   the   battery.
Once
  the   thirty   minutes   have   elapsed,  
the active functions are put on standby
and

  the   battery   warning   lamp   flashes  
accompanied

  by   a   message   in   the  
screen.
T

o   resume   the   use   of   these   functions  
immediately

,   start   the   engine   and   let   it  
run

  for   a   few   minutes.
The
  time   available   will   then   be   double  
the

  time   for   which   the   engine   was   left  
running.

  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery

171
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
The temporary tyre repair kit consists of  a   compressor   and   a   bottle  
(containing

  a   sealant).
Using the kit
1. Tick  the   deflated   wheel   on   the  speed
  limitation   sticker   then   affix  
the

  sticker   to   the   vehicle's   steering  
wheel

  to   remind   you   that   a   wheel   is  
in

  temporary   use.
2.

Clip the bottle
1 on the
compressor 2.
3.

Connect the bottle
1 to the valve of
the
  tyre   to   be   repaired.
4.
 
T
ake   care   to   unwind   the  
compressor

  pipe   before   connecting  
it

  to   the   bottle.
5.

Connect the power lead to one of
the

  vehicle's   12V   sockets.
6.
 
Switch
  on   the   compressor   by  
pressing button

A until the tyre
pressure
  reaches   2.0   bars.   If   this  
pressure cannot be reached, the
tyre

  cannot   be   repaired.
7.
 
Remove
  and   store   the   compressor.
8.
 
Drive
  immediately,   for   a   few   miles  
(kilometres),

  at   reduced   speed,  
to
  fill   the   puncture.
9.
 
Adjust
  the   pressure   using   the  
compressor

  in   accordance   with   the  
recommendation

 
for
 
the
 
vehicle
 
and
 
check

  that   the   leak   is   filled   correctly  
(no

  further   loss   of   pressure).
10.
 
Drive
  at   reduced   speed   (50 mph  
[80

  km/h]).  
The
  tyre   must   be  
examined

  and   repaired   by   a  
specialist

  as   soon   as   possible.
a
fter use, the bottle can be stored in
a   plastic   bag,   supplied   in   the   kit,   to  avoid staining your vehicle with traces
of
  fluid.
Warning:
  the   bottle   of   gel   contains  
ethylene-glycol, a product which
is

  harmful   if   swallowed   and   which  
causes

  irritation   to   the   eyes.
Keep
  it   out   of   reach   of   children.
a

fter use, do not discard the bottle into
the
  environment,   take   it   to   a   CITROËN  
dealer or to an specialised waste
disposal

  site.
Replacement
  bottles   of   sealant   are  
available

  from   CITROËN   dealers.
TEMPORARY PUNCTURE
REP

AIR KIT
The kit is located in one of the two storage   compartments   located  
under

  the   front   seats.
Vehicles
  supplied   with   a   temporary  
puncture

  repair   kit   do   not   have   a   spare  
wheel

  or   tooling   (jack,   wheelbrace,   ...).
QUICk HELP
8
Changing a wheel

172
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
1. Parking the vehicle
- The  occupants   must   get   out   of   the  vehicle
  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 Place   a   chock   under   the   wheel  diagonally opposite the one to be
changed.
CHANGING A WHEEL
2. T

ools
The tools are stowed in a storage area
closed  by   a   flap   under   a   front   seat.
-
 
If
  necessary,   move   the   seat   forward  
to

  access   the   storage   compartment  
from

  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-
 
Remove
  the   tools   needed   from   the  
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Alloy
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 
it

 
is
 
sometimes
 
necessary
 
to
 
raise
 
the

 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to

 
remove
 
the
 
spare
 
wheel
 
from
 
its
 
carrier

.
On
 
certain
 
types
 
of
 
ground
 
and/
or if considerable loads are being
transported, call a CITR
o
Ë
n
dealer or
a
 
qualified
 
workshop.
The
 
jack
 
and
 
tools
 
are
 
specific
 
to
 
your
 
vehicle.

 
Do
 
not
 
use
 
them
 
for
 
other
 
purposes.
Changing a wheel

173
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
3. Spare wheel
- Unscrew the bolt using the
wheelbrace until the carrier is
lowered  fully.
-
o
pen the rear doors to gain access
to
 
the
 
spare
 
wheel. -
 Detach   the   carrier   from   the   hook  and place the spare wheel near the
wheel
  to   be   changed.
QUICk HELP
8
Changing a wheel

174
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
4. Procedure
- Place  the   foot   of   the   jack   in   contact  with the ground directly below the
jacking
  point   closest   to   the   wheel   to  
be

  changed.
-
 
Extend
  the   jack   until   its   head  
comes

  into   contact   with   the   jacking  
point used; the vehicle's contact
area

A   must   be   engaged   with   the  
head

  of   the   jack.
-

Raise the vehicle until there is
sufficient

  space   between   the   wheel  
and the ground, so that


(not punctured) spare wheel can be
easily
  fitted.
-
 
Resume
  and   complete   the  
unscrewing

  of   the   wheel   bolts.
-
 
Remove
  the   bolts   and   remove   the  
wheel.
-

 Remove
 
the
 
wheel
 
trim.
-

Loosen the wheel bolts and start
unscrewing

 
them. Ensure
  that   the   jack   is   stable,   the   foot  of
  the   jack   must   be   in   contact   with   the  
ground,

  and   directly   below   the   jacking  
point

  used.
If the ground is slippery or loose, the
jack
  may   slip   or   drop   -   Risk   of   injury!
Ensure
  that   the   jack   is   positioned   only  
at

  one   of   the   jacking   points   under   the  
vehicle,

  making   sure   that   the   vehicle's  
contact surface is centred on the head
of

  the   jack.
Otherwise
  there   is   a   risk   of   damage  
to

  the   vehicle   and/or   of   the   jack  
dropping -

  Risk   of   injury!
Do
  not   extend   the   jack   until   you   have  
started unscrewing the bolts on the
wheel to be changed and have placed
the

  chock   under   the   wheel   diagonally  
opposite.
Changing a wheel