Electronic immobilizer (Anti-theft starting system) 5-4 Features and controls
5
If you choose to have a certified i-MiEV dealer register the ID
code, take your vehicle
and any remaining keys
to a certified i-MiEV
dealer.
N00562200113
You can program new keys to the system ifyou have two valid (alr
eady registered) keys
and blank (not regist
ered) immobilizer key
(specially cut for your ve
hicle at a certified i-
MiEV dealer) by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the “ON” positionfor 5 seconds. 2. Turn the ignition to the “LOCK” position and remove the first key.3. Within 30 seconds of turning the first key to the “LOCK” position, insert the second valid key into the ignition and turn it tothe “ON” position. About 10 seconds later, the immobilizer indicator will start blinking.
4. When the immobilizer indicator starts blinking, turn the second valid key to the“LOCK” position and remove it. Within 30 seconds after doing so, insert a blank immobilizer key into the ignition and turnit to the “ON” position. Perform this oper- ation no more than 30 seconds after the immobilizer indicato
r starts blinking.
When registration of the ID code is com- plete, the immobilizer indicator will come on for 3 seconds then go off. If an error occurs, the immobilizer indicator will go off during the procedure. 5. If you wish to register another key, per- form the process again from step 1.
N00562300084
Your electronic imm
obilizer operates on a
radio frequency subject
to Federal Communi-
cations Commission (FCC) Rules (For vehi- cles sold in U.S.A.) and Industry CanadaRules (For vehicles so
ld in Canada). This
device complies with
Part 15 of the FCC
Rules and RSS-Gen of the Industry Canada
NOTE
You are provided with
2 keys, but you may
add up to 6 more keys.
Customer key programming (Except for vehicles sold in Canada)
NOTE
It is not possible to register a key if: • the immobilizer indi
cator goes off during
the procedure
• the immobilizer indica
tor does not come on
for 3 seconds after turning the ignition tothe “ON” position with
a blank immobilizer
key
The procedure will be terminated automati- cally if: • a period of 30 seconds or longer elapses from the moment when the first key is turned to the “LOCK” position to the moment when the second key is turned tothe “ON” position • a period of 30 seconds or longer elapses from the moment when the second key is turned to the “LOCK” position to the moment when the blank immobilizer key(specially cut for your
vehicle at a certified
i-MiEV dealer) is turned to the “ON” posi- tion • more than 20 seconds elapse after the immobilizer indicato
r starts blinking
General information
NOTE
BK0209800US.book 4 ページ 2014年1月14日 火曜日 午前9時26分
Keyless entry system
Features and controls 5-5
5
Rules. Operation is subject to the following two conditions. This device may not
cause harmful inter-
ference. This device must ac
cept any interference
received, including interference that maycause undesired operation.
This digital apparatu
s does not exceed the
Class A limits for radi
o noise emissions from
digital apparatus set out in the Radio Interfer- ence Regulations of th
e Canadian Department
of Communications.
N00509000910
Press the remote control transmitter buttonsto lock or unlock the doors and to open the liftgate. It can also help you
signal for attention by
setting off the panic alarm.
Press the LOCK button (1) to lock all the doors and the liftgate. If the dome light switch is in the door posi- tion, the dome light w
ill blink once. The turn
signal lights will also blink once.
Press the UNLOCK button (2) to unlock the driver’s door only. Within about 2 seconds, press the UNLOCKbutton one more time to unlock all the doors and the liftgate. If the dome light switch is in the door posi-tion, the dome light will turn on for about 30 seconds. The turn signal
lights will also blink
twice. The keyless entry system answerback func- tions from the horn can each be turned on or off as desired.
CAUTION Changes or modifica
tions not expressly
approved by the manufacturer for compli- ance could void the user’s authority to oper-ate the equipment.
Keyless entry system
1-
LOCK ( ) button
2-
UNLOCK ( ) button
3- PANIC button 4- Indicator lightTo l o c k
NOTE
If you press the LOCK button (1) after lock- ing the doors and the liftgate, the horn will sound once to confirm that they are locked.
To unlock
NOTE
If the UNLOCK button (2) is pressed and no door or liftgate is opened within approxi- mately 30 seconds, relocking will automati- cally occur (automatic
relocking function).
The time for automatic relocking can be changed. For details,
please contact a certi-
fied i-MiEV dealer. The door and liftgate unlock function can be set so that all doors and liftgate unlock whenthe UNLOCK button (2) is pressed once. For details, please c
ontact a certified i-MiEV
dealer.
Answerback function
BK0209800US.book 5 ページ 2014年1月14日 火曜日 午前9時26分
Keyless entry system
Features and controls 5-7
5
If you choose to have a certified i-MiEV dealer register the ID
code, take your vehicle
and all remaining keys to a certified i-MiEV dealer.
N00546100101
Your keyless entry system operates on a radiofrequency subject to
Federal Communica-
tions Commission (FCC)
Rules (For vehicles
sold in U.S.A.) and Industry Canada Rules (For vehicles sold in Canada). This device complies with Part 15 of the FCC Rules andRSS-Gen of the Industry Canada Rules. Operation is subject to the following two con- ditions. This device may not
cause harmful inter-
ference. This device must ac
cept any interference
received, including interference that maycause undesired operation.
N00544100110
1. Before replacing the
battery, remove static
electricity from your body by touching ametal grounded object. 2. With the Mitsubishi mark facing up, insert the cloth-covered tip of
a flat blade screw-
driver into the notch in the remote control transmitter case and
use it to open the
case.
3. Remove the remote control transmitter from the remote control transmitter case. Then, open the remote control transmitterusing the method described in step 1. 4. Remove the old battery.
NOTE
You are provided with 2 remote control transmitters, but you may register up to 4 remote control transmitters.
General information
CAUTION Changes or modifica
tions not expressly
approved by the manufacturer for compli-ance could void the user’s authority to oper-ate the equipment.
Procedure for replacing the remote control transmitter bat- tery
NOTE
Be sure to perform the procedure with the Mitsubishi mark facing up. If the Mitsubishimark is not facing up when you open theremote control transmitter case, the buttons may come out.
BK0209800US.book 7 ページ 2014年1月14日 火曜日 午前9時26分
Tire pressure monitoring system
Features and controls 5-33
5
The tire pressure monitoring system may not work normally in the following circum- stances: A wireless facility or device using the same frequency is near the vehicle. Snow or ice is stuck inside the fenders and/or on the wheels. The tire inflation pre
ssure sensors’ battery
is exhausted. Wheels other than Mitsubishi Motors gen- uine wheels are being used. Wheels that are not fitted with tire infla- tion pressure sensors are being used. Wheels whose ID codes are not memo- rized by the vehicle are used. A window tint that affects the radio wave signals is installed.
N00532900182
If you use new wheels with new tire inflationpressure sensors, their ID codes must be pro- grammed into the tire pressure monitoring system. Have tire and
wheel replacement per-
formed by a certified i-MiEV dealer to avoid the risk of damaging the tire inflation pres- sure sensors.
N00533000207
Your tire pressure monitoring system oper- ates on a radio frequenc
y subject to Federal
Communications Commission (FCC) Rules(For vehicles sold in
U.S.A.) and Industry
Canada Rules (For vehicles sold in Canada). This device complies wi
th Part 15 of the FCC
Rules and RSS- Gen of the Industry Canada Rules. Operation is subject to the following two con- ditions. This device may not
cause harmful inter-
ference. This device must ac
cept any interference
received, including interference that may cause undesired operation.
Do not use an aerosol puncture-repair spray on any tire. Such a spray could damage thetire inflation pressure sensors. Using the tire repair kit may damage the tire inflation pressure sensor. The vehicle mustpromptly be inspected and repaired by a cer- tified i-MiEV dealer after using the tire repair kit.NOTE
NOTE
Tire inflation pressures vary with the ambi- ent temperature. If the vehicle is subjected tolarge variations in ambient temperature, thetire inflation pressures may be under-inflated (causing the warning light to come on) when the ambient temperature is relatively low. Ifthe warning light comes on, adjust the tire inflation pressure.
Whenever the tires and wheels are replaced with new ones
CAUTION The use of non-genuine wheels will prevent the proper fit of the tire inflation pressure sensors, resulting air
leakage or damage of
the sensors.
General information
CAUTION Changes or modifica
tions not expressly
approved by the manufacturer for compli- ance could void the user
’s authority to oper-
ate the equipment.
BK0209800US.book 33 ページ 2014年1月14日 火曜日 午前9時26分
7
Comfort controlsVents ................................................................................................7-2 Air conditioning ..........
...........
...........
...........
...........
...........
.........
.....7-4
Important air conditioning operating tips ..
...........
...........
.........
.....7-10
Air purifier ..................................................................................... 7-11 Remote Climate Control (if so equipped)....................................... 7-11 AM/FM electronically tuned radio with CD player ...................... 7-11Error codes .....................................................................................7-19 Handling of compact discs .............................................................7-20 Antenna ..........................................................................................7-22Clock ..............................................................................................7-22 General information about your radio .....
...........
...........
...........
.....7-23
BK0209800US.book 1 ページ 2014年1月14日 火曜日 午前9時26分
Air purifier
Comfort controls 7-11
7
The air conditioning should be operated for at least five minutes each week, even in cold weather. This includes the quick defrostingmode. Operating the
air condition system
weekly maintains lubrication of the compres- sor internal parts and maintains the air condi-tioning in the best operating condition.
N00733800177
The air conditioning system is equipped with an air filter to reduc
e pollen and dust entering
the cabin.The air filter’s ability to collect pollen and dust will be reduced as
it becomes dirty, so
replace it periodically. For the maintenanceinterval, refer to the “WARRANTY AND MAINTENANCE MANUAL”.
N00766600016
You can run the air conditioning in advance of using the vehicle. For details, refer to“Remote Climate Control” on page 3-43.
N00734302128
The audio system can only be used when the electric motor switch is in the “ON” or “ACC” position.
CAUTION The air conditioning system in your vehicle must be charged with the refrigerant HFC-134a and the lubricant POE MA68EV.Use of any other refrigerant or lubricant will cause severe damage a
nd may require replac-
ing your vehicle’s en
tire air conditioning
system. The release of refrigerant into the atmo- sphere is not recommended.The new refrigerant HFC-134a in your vehi- cle is designed not to harm the earth’s ozone layer. However, it may contribute slightly toglobal warming. It is recommended that the old refrigerant be saved and recycled for future use.
During a long period of disuse
Air purifier
NOTE
Operation in certain conditions such as driv- ing on a dusty road or frequent use of the air conditioning can reduce
the service life of
the filter. When you feel that the air flow is lower than normal or when the windshield or windows start to fog up easily, replace the airfilter. Contact a certified i-MiEV dealer for assis- tance.
Remote Climate Control
(if so
equipped)
AM/FM electronically tuned radio with CD player
NOTE
To listen to the audio system while the elec- tric motor unit is not running, turn the elec- tric motor switch to the “ACC” position. If the electric motor switch is in the “ACC”position, the accessory power will automati- cally turn off after a certain period of time and you will no longer be able to use theaudio system. The accessory power comes on again if the electric motor switch is turned from the “ACC” position. Refer to “ACCpower auto-cutout f
unction” on page 5-19.
If a cellular phone is
used inside the vehicle,
it may create noise in the audio equipment. This does not mean that anything is wrong with your audio equipment. In such a case,use the cellular phone at
a place as
far away
as possible from the audio equipment. If foreign objects or wa
ter get into the audio
equipment, or if smoke or a strange odor comes from it, immediately turn off theaudio system and have
it checked at a certi-
fied i-MiEV dealer. Never try to repair it yourself. Avoid using the audio system untilit is inspected by a qualified person.
BK0209800US.book 11 ページ 2014年1月14日 火曜日 午前9時26分
AM/FM electronically tune
d radio with CD player
7-12 Comfort controls
7
N00711900716 N00712000408
Turn the VOLUME knob clockwise to increase the volume; counterclockwise todecrease the volume.
The status will be displayed in the display.
N00712100672
1. Press the button repeatedly to select the tone, balance and SCV (Speed Com-pensated Volume) function control to change. The order is: BASS
TREBLE
FADER
BALANCE
SCV
Audio adjust mode OFF
2. Press the SEEK button to change the tone, balance and SCV function setting.The status will be di
splayed in the display.
If the audio system is damaged by foreign objects, water, or fi
re, have the system
checked at a certif
ied i-MiEV dealer.
Volume and tone control panel 1- VOLUME (Volume control) knob 2- SEEK (Audio adjust) button 3- Display4- POWER (On-Off) button 5- (Mode change) buttonTo adjust the volume
NOTE
NOTE
The volume control mode will shut off auto- matically if the anothe
r mode is selected, or
if no adjustment is ma
de within about 2 sec-
onds.
To adjust the tone
A- Adjust mode B- Adjust levelAdjust Mode
AdjustLevel
SEEK button opera-
tion
BASS
-6 to 6
Stronger Weaker
TRE- BLE
Stronger Weaker
FADER
F11 to R11
F (Front) increases
R (Rear) increases
BAL- ANCE
L11 to R11
R (Right) increases
L (Left) increases
BK0209800US.book 12 ページ 2014年1月14日 火曜日 午前9時26分
AM/FM electronically tuned radio with CD player
Comfort controls 7-13
7
To select the desired bass level. To select the desi
red treble level.
To balance the volume from the F (front) and the R (rear) speakers.
To balance the volume from the L (left) and the R (right) speakers. Speed Compensated Volume function is a feature that automatically adjusts the VOL- UME, BASS and TREBLE
settings in accor-
dance with the vehicle speed.The effects of the SCV function can be selected either of three levels (LOW, MID and HIGH). Select the degree of your choiceby pressing the SEEK button. If you want to stop th
e SCV function, select
the OFF.
N00734900902 N00735000913
1. Press the POWER button until it beeps to turn the audio system ON and OFF. The system turns on in the last mode used. Press the RADIO button to turn ON theradio. 2. Press the RADIO but
ton to select the
desired band (AM/FM1/FM2).
SCV
HIGH, MID, LOW, OFF
HIGH MID LOW OFF
HIGH MID LOW OFF
BASS (Bass tone control) TREBLE (Treble tone control) FADER (Front/Rear balance con- trol) Adjust Mode
AdjustLevel
SEEK button opera-
tion
BALANCE (Left/Right balance control) SCV (Speed Compensated Vol- ume) function
NOTE
The audio adjust mode will automatically shut off when another m
ode is selected, or if
no adjustment is made within about 10 sec-onds.
Radio control panel and display 1- FM (FM1/FM2) indicator 2- RADIO (AM/FM selection) button3- MEMORY (Memory selection) button 4- POWER (On-Off) button 5- SCAN button6- SEEK (Up-seek) button 7- SEEK (Down-seek) buttonTo listen to the radio
BK0209800US.book 13 ページ 2014年1月14日 火曜日 午前9時26分