2015 Lexus CT200h Owner's Manual (in English)

512
CT200h_OM_OM76174U_(U)7-3. Do-it-yourself maintenance
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb with
the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to check
that it is not loose, turn the headlight
high beams on once and visually
confirm that no light is leaking
through the mounting.
When installing the cover, conduct step in reverse.
■Halogen fog light (if equipped)
Remove 2 screws, a bolt and clip,
and pull down the fender liner.
Pull the fender liner down slowly,
being careful not to dislodge any
fixed components.
4
5
61
1

CT200h_OM_OM76174U_(U)
5137-3. Do-it-yourself maintenance
7
Maintenance and care
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the fog lights on once
and visually confirm that no light is
leaking through the mounting.
2
3
4
5

514
CT200h_OM_OM76174U_(U)7-3. Do-it-yourself maintenance
Reinstall the fender liner with 2
screws, a bolt and clip.
■Front turn signal lights (halogen headlights)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■Front turn signal lights (LED headlights)
XLeft side
Remove the power control unit
cover.
6
1
2
1

CT200h_OM_OM76174U_(U)
5157-3. Do-it-yourself maintenance
7
Maintenance and care
Turn the bulb base counterclock-
wise.
Remove the light bulb.
XRight side
Move the washer fluid filler opening. (→P. 5 1 0 )
Turn the bulb base counterclock-
wise.
Remove the light bulb.
2
3
1
2
3

516
CT200h_OM_OM76174U_(U)7-3. Do-it-yourself maintenance
■Rear turn signal lights
Open the back door and remove
the covers and bolts, and remove
the lamp assembly by pulling it
directly backward from the rear
of the vehicle.
Use a flathead screwdriver wrapped
in a cloth.
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■Back-up lightsOpen the back door and remove
the cover.
Use a flathead screwdriver wrapped
in a cloth.
1
2
3
1

CT200h_OM_OM76174U_(U)
5177-3. Do-it-yourself maintenance
7
Maintenance and care
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by your Lexus
dealer.
●Headlight low beams (LED type)
●Parking lights and daytime running lights
●LED fog lights (if equipped)
●Front side marker lights
●Side turn signal lights
●Stop/tail lights
●Rear side marker lights
●High mounted stoplight
●License plate lights
●Outer foot lights
■After replacing the bulbs
2
3
After removing the power control unit cover,
return the cover to original position with the
clips.Push up center portion
Insert
Press
1
2
3

518
CT200h_OM_OM76174U_(U)7-3. Do-it-yourself maintenance
■LED lights
The headlight low beams (LED type), parking lights, front side marker lights, daytime
running lights, LED fog lights (if equipped), side turn signal lights, rear side marker lights,
stop/tail lights, high mounted stoplight and license plate lights consist of a number of
LEDs. If any of the LEDs burn out, take your vehicle to your Lexus dealer to have the light
replaced.
■Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside
of the headlight lens does not indicate a
malfunction. Contact your Lexus dealer for more information in the following situations:
●Large drops of water have built up on the inside of the lens.
●Water has built up inside the headlight.
■When replacing light bulbs
→ P. 5 0 6
WA R N I N G
■Replacing light bulbs
●Be sure to stop the hybrid system and turn off the lights. Do not attempt to replace the
bulb immediately after turning off the lights.
The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bulb with bare hands. When it is unavoid-
able to hold the glass portion, use and hold with a clean dry cloth to avoid getting
moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may result
in heat damage, fire, or water entering th e headlight unit. This may damage the head-
lights or cause condensation to build up on the lens.
●Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or
component parts.
Doing so may result in death or se rious injury due to electric shock.
■To prevent damage or fire
●Make sure bulbs are fully seated and locked.
●Check the wattage of the bulb before installing to prevent heat damage.

519
CT200h_OM_OM76174U_(U)
8When trouble arises
8-1. Essential informationEmergency flashers .................. 520
If your vehicle has to be stopped in an
emergency...................................521
8-2. Steps to take in an emergency
If your vehicle needs to be towed ..................................... 522
If you think something is wrong ........................................... 526
If a warning light turns on or a warning buzzer
sounds.......................................... 527
If a warning message is displayed..................................... 534
If you have a flat tire................... 547
If the hybrid system will not start ............................................... 557
If the electronic key does not operate properly ..................... 559
If the 12-volt battery is discharged ...................................561
If your vehicle overheats ......... 565
If the vehicle becomes stuck ............................................. 569