2015 Citroen C4 PICASSO Owner's Manual

263
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block   traffic:   the   ground   must   be   level,  
s

table   and   not   slippery.
Apply
  the   parking   brake   unless   it   has  
b

een   programmed   to   automatic   mode,  
s

witch   off   the   ignition   and   engage   first  
g

ear*   to   block   the   wheels.
Check
  that   the   braking   warning   lamp  
a

nd   the   P   warning   lamp   in   the   parking  
b

rake   control   lever   come   on.
For
  greater   safety,   place   the   chock   2
against
  the   wheel   opposite   to   the   one  
b

eing
 c
hanged.
The
  occupants   must   get   out   of   the  
v

ehicle   and   wait   where   they   are   safe.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.
List of operations
F Remove  the   finisher   from   from   each  o
f   bolts   using   the   tool   4   (depending   on  
e

quipment).
F
 
F
it   the   security   socket   5 on the
wheelbrace


1   to   slacken   the   security   bolt  
(

if fitted).
F
 
S
lacken   the   other   bolts   (no   more   than   a  
1

/4 turn)   using   the   wheelbrace   1  
o
n l y.
*


Position R
 
for
 
an
 
electronic
 
gearbox
 
or
 
P for
an
 
automatic
 
gearbox. Do
  not   use:
-
 
t
he   jack   for   any   purpose   other   than  
l

ifting   the   vehicle,
-
 
a
ny   other   jack   than   the   one  
s

upplied   by   the   manufacturer.
7
Practical information

264
F Place  the   foot   of   the   jack   3   on   the   ground  a
nd   check   that   it   is   directly   below   the  
f

ront A or rear B   jacking   point   provided   on  
t

he   underbody,   whichever   is   closest   to   the  
w

heel   to   be   changed. F
 E xtend   the   jack   3   until   its   head   comes   into   contact   with   the   jacking   point   A or B   used;  t
he vehicle's   contact   sur face   A or B   must   engage   with   the   central   part   of   the   head   of   the   jack.
F
 
R
aise   the   vehicle   until   there   is   sufficient   space   between   the   wheel   and   the   ground   to   admit   the  
s

pare   (not   punctured)   wheel   easily.
Ensure
  that   the   jack   is   stable.   If   the  
g

round   is   slippery   or   loose,   the   jack  
m

ay   slip   or   drop   -   Risk   of   injury!
Ensure
  that   the   jack   is   positioned   only  
a

t   one   of   the   jacking   points   A or B
under
  the   vehicle,   making   sure   that   the  
v

ehicle's   contact   sur face   is   centred   on  
t

he   head   of   the   jack.   Other wise   there   is  
a

  risk   of   damage   to   the   vehicle   and/or   of  
t

he   jack   dropping   -   Risk   of   injury!
Practical information

265
F Remove  the   bolts   and   store   them   in   a   clean  p
lace.
F
 
R
emove   the   wheel.
Fitting a wheel
Fitting the "space-saver"
spare wheel
If your vehicle is fitted with alloy wheels, when   tightening   the   bolts   on   fitting,   it  
i

s   normal   to   notice   that   the   washers  
d

o   not   come   into   contact   with   the  
"

space-saver"   spare   wheel.   The   wheel  
i

s   secured   by   the   conical   sur face   of  
e

ach   bolt.
After changing a wheel
To correctly store the punctured wheel in   the   boot   (not in the location of the
space-saver wheel ),
  first   remove   the  
c

entral   cover.
When
  using   the   "space-saver"   type  
s

pare   wheel,   do   not   exceed   50   mph  
(

80 km/h).
Have
  the   tightening   of   the   bolts   and   the  
p

ressure   of   the   spare   wheel   checked  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop   without   delay.
Have
  the   punctured   wheel   repaired  
a

nd   refitted   to   the   vehicle   as   soon   as  
p

ossible.
7
Practical information

266
F Lower  the   vehicle   fully.
F  F old   the   jack   3   and   detach   it.F
 T ighten   the   security   bolt   using   the  w
heelbrace 1   fitted   with   the   security  
s

ocket 5
  (depending   on   equipment).
F
 
T
ighten   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
F

R
efit the bolt covers on each of the bolts or
the
  hub   cap   (depending   on   equipment).
F
 
S
tore   the   tools   in   the   box.
List of operations
F Put  the   wheel   in   place   on   the   hub.
F  S crew   in   the   bolts   fully   by   hand.
F
 
P
re-tighten   the   security   bolt   using   the  
w

heelbrace 1   fitted   with   the   security  
s

ocket  5
  (depending   on   equipment).
F
 
P
re-tighten   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
Practical information

267
Original tyre sizeSpec ification of
chains.
205/60
  R16 Maximum
  link   size:  
9

  mm
205/55
  R17
225/45
  R18 THULE
  model  
K-Summit
  K34   only
For
  more   information   on   snow   chains,   contact   a  
C

ITROËN   dealer   or   a   qualified   workshop.
Use
  only   chains   designed   to   be   fitted   the   type  
o

f
 
wheel   on   your   vehicle:
Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when braking.
T he   snow   chains   must   be   fitted   only  
t

o   the   front   wheels.   They   must   never  
b

e   fitted   to   "space-saver"   type   spare  
w

heels.
Advice on installation
F If  you   have   to   fit   the   chains   during   a  j
ourney,   stop   the   vehicle   on   a   flat   sur face  
o

n   the   side   of   the   road.
F
 
A
pply   the   parking   brake   and   position   any  
w

heel   chocks   to   prevent   movement   of   your  
v

ehicle.
F
 
F
it   the   chains   following   the   instructions  
p

rovided   by   the   manufacturer.
F
 
M
ove   off   gently   and   drive   for   a   few  
m

oments,   without   exceeding   30   mph  
(

50 km/h).
F
 
S
top   your   vehicle   and   check   that   the   snow  
c

hains   are   correctly   tightened.
Take
 
account
 
of
 
the
 
legislation
 
in
 
force
 
i

n your country on the use of snow
chains
 
and
 
the
 
maximum
 
running
 
speed
 
a

uthorised. Avoid
  driving   with   snow   chains   on   roads  
t

hat   have   been   cleared   of   snow,   to  
a

void   damaging   your   vehicle's   tyres   and  
t

he   road   sur face.   If   your   vehicle   is   fitted  
w

ith   alloy   wheels,   check   that   no   part   of  
t

he   chain   or   its   fixings   is   in   contact   with  
t

he   wheel   rim.
It
 
is
 
strongly
 
recommended
 
that
 
before
 
y

ou
 
leave,
 
you
 
practise
 
fitting
 
the
 
snow
 
c

hains
 
on
 
a
 
level
 
and
 
dry
 
sur face.
7
Practical information

268
Changing a bulb
For H7 type bulbs with lugs... take care to observe their correct installation
so
  as   to   ensure   the   best   lighting  
p

erformance.
Risk of electrocution
Xenon bulbs (D5S-25W) must be replaced   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Front lamps
Model with xenon headlamps
1. Directional   dipped   beam   headlamps  
(D5S-25W).
2.
 M

ain   beam   headlamps   (H7-55W).
3.
 D

aytime   running   lamps   /   sidelamps
 (

6   light   emitting   diodes   -   LEDs).
4.
 D

irection
 i
ndicators
 (

6   light   emittng   diodes   -   LEDs).
5.
 F

ront   foglamps   (H11-55W).
Model with halogen headlamps
1. Dipped  beam   headlamps   (H7-55W).
2. M ain   beam   headlamps   (H7-55W).
3.
 D

aytime
 r
unning
 lam
ps/sidelamps
 (

4   light   emitting   diodes   -   LEDs).
4.
 D

irection   indicators   (PW Y24W).
5.
 F

oglamps
 (
H11-55W). In
  some   weather   conditions   (e.g.   low  
t

emperature   or   humidity),   the   presence  
o

f   misting   on   the   internal   sur face   of   the  
g

lass   of   the   headlamps   and   rear   lamps  
i

s   normal;   it   disappears   after   the   lamps  
h

ave   been   on   for   a   few   minutes.
Light emitting diodes-LEDs
For replacement, contact a CITROËN dealer or q
ualified w orkshop.
Practical information

269
Directional dipped beam
headlamps (xenon model)Main beam headlamps (xenon model)
F Remove  the   protective   plastic   cover   by  p
ulling   the   tab.
F
 
P
ush   the   connector.
F
 
R
emove   the   bulb   and   change   it.
For
  reassembly,   carry   out   these   operations   in  
r

everse
 o
rder.
D5S
 
xenon
 
bulbs
 
must
 
be
 
changed
 
b

y
 
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 
w

orkshop,
 
as
 
there
 
is
 
a
 
risk
 
of
 
el

ectrocution.
In
 
the
 
event
 
of
 
failure
 
of
 
one
 
of
 
the
 
D5S
 
b

ulbs,
 
it
 
is
 
recommended
 
that
 
the
 
bulb
 
o

n
 
the
 
other
 
side
 
be
 
changed
 
at
 
the
 
s

ame
 
time.
The
 
headlamps
 
are
 
fitted
 
with
 
p

olycarbonate
 
glass
 
with
 
a
 
protective
 
c

oating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F
 
u

se
 
a
 
sponge
 
and
 
soapy
 
water
 
or
 
a
 
p

H
 
neutral
 
product,
F
 
w

hen
 
using
 
a
 
high
 
pressure
 
washer
 
o

n
 
persistent
 
marks,
 
do
 
not
 
keep
 
t

he
 
lance
 
directed
 
towards
 
the
 
l

amps
 
or
 
their
 
edges
 
for
 
too
 
long,
 
s

o
 
as
 
not
 
to
 
damage
 
their
 
protective
 
c

oating
 a

nd
 sea

ls.
Changing
 
a
 
bulb
 
should
 
only
 
be
 
done
 
a

fter
 
the
 
headlamp
 
has
 
been
 
switched
 
o

ff
 
for
 
several
 
minutes
 
(risk
 
of
 
serious
 
b

urns).
F
 
D

o
 
not
 
touch
 
the
 
bulb
 
directly
 
with
 
y

our
 
fingers,
 
use
 
a
 
lint-free
 
cloth.
It
 
is
 
imperative
 
to
 
use
 
only
 
anti-
ultraviolet
 
(UV)
 
type
 
bulbs
 
to
 
avoid
 
d

amaging
 t

he
 h

eadlamp.
Always
 
replace
 
a
 
failed
 
bulb
 
with
 
a
 
n

ew
 
bulb
 
with
 
the
 
same
 
type
 
and
 
s

pecification.
7
Practical information

270
Dipped beam headlamps
(halogen model)
F Remove  the   protective   plastic   cover   by  p
ulling   the   tab.
F
 
P
ush   the   connector.
F
 
R
emove   the   bulb   and   change   it.
For
  reassembly,   carry   out   these   operations   in  
r

everse
 o
rder.
Main beam headlamps
(halogen model)
F Turn the protective plastic cover to remove   it.
F
 
D
isconnect   the   connector.
F
 
R
elease   the   clips.
F
 
R
emove   the   bulb   and   change   it.
For
  reassembly,   carry   out   these   operations   in  
r

everse
 o
rder.
Daytime running lamps / sidelamps
For the replacement of this type of LED lamp and   lighting   guides,   contact   a   CITROËN   dealer  
o

r   a   qualified   workshop.
A
  replacement   kit   for   the   LEDs   is   available   from  
C

ITROËN   dealers.
Practical information