2015 Citroen BERLINGO MULTISPACE Owner's Manual

 63
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
Changing the
programmed speedSwitching the system off
Operating fault Cancelling the programmed
speed setting
When the vehicle becomes stationary, after switching of
f the ignition, the
system
  no   longer   memorises   a   speed.
There
 
are
 
two
 
methods
 
of
 
memorising
 
a speed

higher
 
than
 
the
 
previous
 
one:
-
Place the dial in position
0 or switch
off the ignition to switch everything
off.
Good practice
Without using the accelerator
-

Press the
SET +   button.
A brief   press   increases   the   speed   by   1   mph   (km/h).
A maintained   press   increases   the   speed   in steps
  of   5   mph   (km/h).
Using the accelerator
-
 
Exceed
  the   memorised   speed   until  
the speed required is reached,
-


Press the
SET + or SET -   button.
To
  memorise   a   speed   lower than the
previous
  one:
-

Press the
SET -   button.
a brief press decreases the speed by


1
  mph   (km/h).
A
 

maintained   press   decreases   the  
speed

  in   steps   of   5   mph   (km/h).The
  programmed   speed   setting   is  
cleared

  and   replaced   by   three   dashes.  
Contact a CITR

o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.When

  changing   the   programmed  
speed

  setting   by   means   of   a  
maintained

  press,   pay   attention   as  
the speed can increase or decrease
rapidly

.
d

o not use the cruise control on
slippery   roads   or   in   heavy   traffic.
In the event of a steep slope, the cruise
control   cannot   prevent   the   vehicle   from  
exceeding

  the   programmed   speed  
setting.
In any event, the cruise control cannot
replace the need to observe the speed
limits

  and   the   need   for   vigilance   on   the  
part

  of   the   driver.
It   is   advisable   to   keep   your   feet   near  
the

  pedals.
To   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-  
never
  place   one   mat   on   top   of  another
.
Steering mounted controls
EASE OF USE and COMFORT
4

64
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
The speed of the vehicle responds to
the pressure of the driver's foot, up
to the the accelerator pedal's point of
resistance, which indicates that the
programmed  speed   has   been   reached.
However, pressing the pedal beyond
this
  point   of   resistance   to   the   floor  
allows

  the   programmed   speed   to   be  
exceeded.

 
T
o   resume   use   of   the   limiter,  
simply

  reduce   the   pressure   on   the  
accelerator pedal gradually and return
to

  a   speed   below   that   programmed.
Adjustments can be carried out
when stationary, with the engine
running, or with the vehicle moving. This
  speed   limiter   shows   the   function  
selection

  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:SPEED LIMITER
"LIMIT"
Function selected,
displaying of the
"Speed
  Limiter"  
symbol.
Function of

f,
last
  programmed  
speed -

OFF.
Function
  on.
Vehicle speed above,
the
  programmed  
speed setting is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
1.
 
Limiter

 
mode
 
On
 
/
 
Off.
2.
 
Reduce

 
programmed
 
speed
 
setting.
3.

 
Increase

 
programmed
 
speed
 
setting.
4.

 
Speed

 
limiter
 
On
 
/
 
Pause.
"This is the selected speed which the
driver
 
does
 
not
 
wish
 
to
 
exceed".
This
 
selection
 
is
 
made
 
with
 
the
 
engine
 running while stationary or with the vehicle


moving.
 
The

 
minimum
 
speed
 
which
 
can
 be

 
programmed
 
is
 
20
 
mph
 
(30
 
km/h).
Steering mounted controls

 65
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
Selecting the functionProgramming a speed setting On / Off
- Place the switch in the LIMIT
position.  The   limiter   is   selected  
but

  is   not   yet   active.  
The
  screen  
indicates

  the   last   programmed  
speed

  setting.
A
 

speed   can   be   programmed   without  
activating

  the   limiter   but   with   the  
engine

  running.
To
  memorise   a   speed   higher than the
previous
  one:
-

Press the
SET +   button.
A brief   press   increases   the   speed   by   1 mph   (km/h).
A
 
maintained   press   increases   the   speed   in   steps   of
 5

  mph   (km/h).
To memorise a speed lower than the
previous   one.
-

Press the
SET -   button.
A brief   press   decreases   the   speed   by   1   mph   (km/h).
A
 
maintained   press   decreases   the   speed   in   steps   of
 5

  mph   (km/h).
Pressing this button once activates
the  limiter,   pressing   the   button   again  
deactivates it

(OFF).
Steering mounted controls
EASE OF USE and COMFORT
4

66
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
Exceeding the programmed
speedSwitching the function offOperating fault
The programmed speed is cleared then
  replaced   by   three   dashes.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.
Flashing of the speed setting
Good practice
In  any   event,   the   speed   limiter   cannot  
replace the need to observe speed
limits,

  nor   can   it   replace   the   need   for  
vigilance

  on   the   part   of   the   driver.
Always
  pay   attention   to   the   profile  
of the road and sharp acceleration
and

  stay   in   complete   control   of   your  
vehicle.
T

o   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-
 
never
  place   one   mat   on   top   of  
another

.
Pressing the accelerator pedal in order
to
 
exceed
 
the
 
programmed
 
speed
 
will have no ef

fect unless you press
the pedal firmly beyond the point of
resistance.
The
 
limiter
 
is
 
deactivated
 
temporarily
 
and

 
the
 
programmed
 
speed
 
flashes
 accompanied
 
by
 
an
 
audible
 
signal.
To
 
return
 
to
 
the
 
limiter
 
function,
 
reduce
 
your

 
speed
 
to
 
below
 
the
 
programmed
 
speed.
The

 
speed
 
setting
 
flashes:
-

following forcing of the accelerator
point of resistance,
-

 
when

 
the
 
limiter
 
cannot
 
prevent
 
an
 
increase in the vehicle speed due
to

 
the
 
profile
 
of
 
the
 
road
 
or
 
on
 
a
 
steep descent,
-

 
in

 
the
 
event
 
of
 
sharp
 
acceleration. -

Place the switch in position

0 or
switch off the ignition to switch the
system
 
off.
The
 
last
 
programmed
 
speed
 
remains
 
in
 
the

 
memory.
Steering mounted controls

 67
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
VENTILATION
the side vents and the central
vents,
Air flow
the footwells,
the windscreen and the footwells,
the windscreen.
The air distribution can be
modulated
  by   placing   the  
control

  in   the   intermediate  
positions,

  marked   "●".
Air distribution
The air supply distribution is
determined  by   the   following   symbols:
in the red zone, provides
heating of the passenger
compartment. in the blue zone, provides
ambient
 
air,
The speed of the blown air at
the  vents   varies   from   1   to   the  
fastest

  4.   Position   0   switches  
it

  off.
Adjust   this   control   in   order  
to

  attain   the   desired   comfort  
level.
Heating
Manual air conditioning
Temperature
Control positioned:
EASE OF USE and COMFORT
4
Ventilation

68
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
Intake of exterior air
Recirculation of interior airAir conditioning A/C
The LEd in the button is
of f.  This   is   the   preferred  
operating

  position.
Pressing the button starts
the
  air   conditioning   system,  
the

  LED   is   on.   Pressing   the  
button again switches the
function of

f and the LE d goes
off.
The air conditioning does not operate if
the
  fan   speed   is   set   to   0.
The air conditioning can only operate
with
  the   engine   running.
The
  LED   in   the   button   is   on.  
Recirculation

  temporarily  
prevents exterior odours
and

  smoke   from   entering   the  
passenger

  compartment.
Used with the setting of the fan speed
(from
 
1
 
to   4),   recirculation   enables   you  
to

 
attain
 
the   desired   comfort   level   more  
quickly

 
with   both   hot   or   cold   settings.
This
 
position   should   only   be   temporary.  
When

 
your   desired   comfort   level   has  
been

 
reached,   return   to   the   intake  
of

 
exterior   air   position   to   permit  
renewal of the air in the passenger
compartment

  and   avoid   misting.  
This
  is  
the

 
preferred   operating   mode.
Ventilation

 69
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
Good practice
For maximum cooling or heating of the passenger  compartment,   it   is   possible  
to exceed the value 15 by turning until
LO

  is   displayed   or   the   value   27   by  
turning

  until   HI   is   displayed.
o

n entering the vehicle, the inside
temperature
  may   be   much   colder  
(or
  warmer)   than   is   comfortable.  
There
 
is no advantage in changing the value
displayed

  in   order   to   quickly   reach   the  
level

  of   comfort   required.  
The
  system  
will

  use   its   maximum   performance   to  
reach

  the   comfort   value   set.
DIGITAL AIR CONDITIONING
Automatic operation
AUTO comfort programme
This
  is   the   normal   air   conditioning  
system

  operating   mode. Driver or passenger side comfort
value
The value indicated in the screen
corresponds
  to   a   level   of   comfort   and  
not

  a   temperature   in   degrees   Celsius  
or

  Fahrenheit.
Turn this control to the left
or to the right to decrease or
increase   the   value.  
A 
setting  
around the value 21 provides
optimum

  comfort.   However,  
depending

  on   your   requirements,   a  
setting

  between   18   and   24   is   usual.
d

o not cover the sunshine sensor
located
  on   the   dashboard.
Press this button, the AUTO
symbol
  is   displayed.
The
  system   controls   the  
distribution,

  the   flow   and   the  
intake

  of   air   to   guarantee  
comfort

  and   a   sufficient   circulation  
of

  air   in   the   passenger   compartment  
according

  to   the   comfort   value   set.   No  
further

  action   on   your   part   is   required.Air
  flow   will   increase   gradually   when  
the

engine is cold, to prevent excessive
distribution   of   cold   air.
For your comfort, the settings are stored when the ignition is switched of
f and are
reinstated
  the   next   time   the   vehicle   is
 started.
The

  automatic   function   will   no   longer   be
 maintained

  if   you   change   a   setting   manually
 (AUT

O   is   cleared).
SEPARATE SETTINGS FOR DRIVER AND PASSENGER
EASE OF USE and COMFORT
4
Ventilation

70
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
Manual operation
You can, according to your
requirements,  make   a   different   selection from

  that   offered   by   the   system   by
 changing

  a   setting.  
The
  other   functions
 will

  still   be   controlled   automatically.
 Pressing the

AUTO button restores fully
automatic
  operation.
Air distribution
Pressing this button several
times
  in   succession   directs  
the

  air   flow   towards:
-

the windscreen,
-


the windscreen and footwells,
-


the footwells,
-


the side vents, central vents and
footwells,
-

 
the
  side   vents   and   central   vents.Air flow
Press the small fan button to
reduce
  the   flow   or   the   large
fan button to increase the
flow.
On
  the   display,   the   blades   of   the   fan   fill  
when

  the   flow   is   increased.
Switching the air
conditioning On / Off
Press this button, the A/C
symbol
  is   displayed   and   the  
air

  conditioning   is   activated.
Deactivating the system
Press
  the   air   flow   small fan
button
  until   the   fan   symbol  
disappears

  from   the   display.
This action deactivates all
of
  the   system's   functions,   with   the  
exception of the air recirculation and
rear

  screen   demisting   (if   fitted   on   your  
vehicle).

 
Y
our   comfort   setting   is   no  
longer

  maintained   and   is   switched   off.Intake of exterior air /
Recirculation of interior air
Press this button to
recirculate
  the   interior   air.  
The

  recirculation   symbol   is  
displayed.
Pressing the

large fan
button or the AUTO button
reactivates
  the   system   with  
the values set before it was
deactivated.Recirculation prevents exterior odours


and
  smoke   from   entering   the   passenger
 compartment.

 
A
void   prolonged   operation
 in

  interior   air   recirculation   mode   (risk   of
 condensation,

  odour   and   humidity).
Pressing this button again activates the
intake
  of   exterior   air.
Pressing this button again switches off
the
  air   conditioning.
The ventilation outlet, located
in the glove box, diffuses cool
air (if the air conditioning is
on) regardless of the reference
temperature
  requested   in   the  
passenger

  compartment   and  
regardless

  of   the   exterior   temperature.
For
  your   comfort,   do   not   deactivate   the  
system

  for   long   periods.  
Ventilation