2015 AUDI Q5 Owners Manual

M N
co ~ co
rl I.O
"' N
"' rl
-Position the jack * only at the designated
lift ing po ints and align the jack* . Other­
wise, the jack* could slip and cause an in­
jury if it does not have suffic ient hold on
the vehicle .
- A soft or unstab le surface under the jack*
may cause the vehicle to slip
off the jack*.
Always provide a firm base for the jack * on
the ground. If necessa ry, us e a sturdy
board under t he ja ck*.
- On ha rd, slippery surface (such as til es)
use a rubbe r mat or similar to prevent the
jack* from slipp ing.
- T o help prevent injury to yourself and your
passenge rs:
- Do not raise the vehicle until yo u are sure
the jack* is secure ly engaged.
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wa it in a safe
p lace away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack *.
(D Note
Do not lift the vehicle by the si ll. Pos ition the
jack * only at the designated lifting points on
the si ll. Otherwise, your ve hicle wi ll be dam­
aged.
Em erg en cy ass is tan ce
Taking the wheel off /installing the
inflatable spare tire
Follow these instructions step-by-step for chang­
ing the wheel
F ig . 22 1 Chang in g a whee l: usin g t he screwdr iver hand le
(w ith the blade re moved) to turn the bolts
Fig . 222 Cha ng ing a w hee l: alig nment pin inside the top
h ole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and re­
place the wheel as follows:
Removing th e wheel
.,. Use the hexagonal socket in the screwd river
h andle
to comp letely remove the topmost
wheel bo lt and set it aside on a
clean surface
¢fig. 221 .
.,. Screw the threaded end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole
¢ fig . 222 .
.,. Then remove the othe r whee l bolts as described
above .
.,. Ta ke
off the whee l leaving the a lignment pin in
t he bolt hole
c;, (D _
Putting on th e inflatable spare tire*
.,. Inflate the inflatable spare tire* ¢ page 257
and push the wheel over the alignmen t pin.
263

Emergency assistance
"' Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel bolts
slightly.
"'Remove the alignment pin and insert and tight­
en the remaining wheel bolt slightly like the
rest.
"'T urn the jack handle* counter-clockwise to low­
er the vehicle until the jack* is fully released .
"'U se the whee l bolt wrench to tighten all wheel
bolts firmly¢
page 261. Tighten them cross­
wise,
from one bolt to the (approximately) op­
posite one, to keep the wheel centered.
@ Note
When removing or installing the wheel, the
r im could hit the brake rotor and damage the
rotor. Work carefu lly and have a second per­
son help you.
(D Tips
Never use the hexagonal socket in the handle
of the screwdriver to loosen or tighten the
wheel bolts.
- Pull the reversib le blade from the screwdriv­
er before you use the hexagonal socket in
the handle to turn the wheel bolts.
- When mounting tires with
unidirectional
tread design
make sure the tread pattern is
pointed the right way
¢page 264.
-The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of bot h the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When us ing a spare tire w ith a tread pattern in­
tended for use in a specific direct ion, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire .
264
-If the spare tire has to be installed in the incor­
rect direction, use the spare tire only tempora ­
r il y since the tire w ill not be ab le to achieve its
optimum performance character istics with re­
gard to aquaplaning, noise and wear.
- We recommend that you pay part icu lar atten­
tion to th is fact during wet weather and that
you adjust your speed to match road condi­
tions.
- Replace the flat tire with a new one and have it
installed on your veh icle as soon as possible to
resto re the handling advantages of a unidirec­
tional tire.
Notes on wheel changing
Please read the information ¢ page 242, New
tires ar wheels
if you are going to use a spare tire
which is different from the tires on your vehicle .
After you change a tire:
- Check the tire pressure on the spare immedi­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
105 ft lb (140 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
&_ WARNING
- If you are going to equ ip your vehi cle w ith
tires or rims which differ from those which
were factory installed, then be sure to read
the information ¢
page 242, New tires or
wheels .
-

M N
co
a:
co
,...., \!) ..,.,
N ..,., ,....,
-Always make sure the damaged wheel or
even a flat tire and the jack* and tool kit are
properly secured in the luggage compart­
ment and are not loose in the passenger
compartment .
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the ve ­
hicle.
- Always store damaged wheel, jack* and
tools securely in the luggage compartment .
Otherw ise, in an acc ident or sudden maneu­
ver they could fly forward, causing injury to
passengers in the vehicle.
Emergency assistance
265

Fuses and bulbs
Fuses and bulbs
Fuses
Replacing fuses
A fuse that has blown will have me tal strips that
have burned through.
Fig. 2 23 Left side of the coc kp it: c ove r
The fuses a re located at the fron t left and right of
the cockpit and behind the trim on the right side
of the luggage compartment.
• Swi tc h the ign ition and all e lec trica l equipment
off .
• Check the following table to see which fuse be­
longs to the equipment.
• Remove the appropriate cover.
~ Remove the colored p lastic clip from the fuse
panel, if necessary ¢
page 267, fig. 224. You
can d ispose of the p lastic clip .
• Remove the clamp from the rear side of the
c over ¢
fig. 223 .
• Remove the fuse using the clamp.
• Rep lace the blow n fuse o nly w it h a n ident ica l
new one.
• Install the cover .
Fuse color identification
Color Current
rating
in amps
B lack 1
Purp le
3
Light brown
s
Brown 7.5
R ed 10
B lue 15
Yellow 20
266
Color Current rating
in amps
W hite or transparent
2S
green 30
orange 40
A WARNING
Do not repair fuses and never replace a blown
fuse with one tha t has a hig her amp rating.
T hi s ca n cau se da mage to the e lec trica l sy s­
tem and a fire .
(D Note
If a new fuse burns out again sho rtly after you
have install ed it, have th e electri cal syst em
che cked as soon as possib le by an autho rize d
A udi dealer or au tho riz ed Au di Service Facili ­
ty .
{i) Tips
- T he followi ng tab le does not list fuse loca­
tion s that a re n ot u sed .
- Some of the e quipment listed in the fo llow­
ing table s applies on ly to cert ain model ve r­
si ons or certain op tion al equi pment .

M N
co ~ co
rl I.O
"' N
"' rl
Left cockpit fuse assignment
Fig. 224 Left side of the cockpit: fuse panel with plastic
clip
Fuse panel @ (black )
No. Equipment
1 Dynamic steering
2 ESC control module
A/C system pressure sensor, electrome-
3 chanical park
ing brake, Homelink, auto-
matic dimming interior rearview mirror, air
quality/outside air sensor, ESC button
5 Sound
actuator/exhaust sound tuning
6 Headlight range contro l/cornering light
7 Headlight (cornering light)
Control modu les (e lectromechanical park-
8 ing brake, shock absorber, quattro Sport,
trailer hitch), DCDC converter
9
Adaptive cruise control or high voltage
battery (hybrid drive)
11 Side assist
12 Headlight range control, parking system
13 Airbag
14 Rear w iper
15 Auxi
liary fuse (instrument panel)
1 6 Auxiliary fuse terminal 15 (engine area) Fuses
and bulbs
Fuse panel @ (brown)
No . Equipment
1 Electric exhaust door
2 Brake light sensor or brake pedal
move-
ment sensor (hybr id drive)
3 Fuel pump
4 AdBlue pumps
or brake booster power
supply (hybrid dr ive)
5 Left seat heating with/without seat venti-
lation
6 ESC
7 Horn
8 Left
front door (window regulator, central
locking, mirror, switch, lighting)
9 Wiper motor
10 ESC
11 Left
rear door (window regu lator, switch,
lighting)
12 Rain and light sensor
Fu
se panel © (re d)
No . Equipment
3 Lumbar support
4 Dynamic steering
5 Climatized cupholder
6 Windshie
ld washer system, headlamp
washer system
7 Vehicle electr ical system control module 1
8 Vehicle e
lectrica l system control module 1
9 Panorama sunroof
10 Vehicle e lectrica l system control module 1
11 Sun shade (pano rama sunroof)
12 Anti-theft a
larm system
267

Fuses and bulbs
Right cockpit fuse assignment
Fig . 225 Right s ide of the cockpit: fuse panel wit h plastic
clip
Fuse panel @ (black)
No. Equipment
5 Steering column sw
itch module
7 Terminal 15 diagnostic connector
8 Gateway (Oatabus diagnostic interface)
9 Auxiliary heater
Fuse panel@ (brown)
No. Equipment
1 CD /DVD player
2 Wi-Fi
3 MM I/Radio
4 Instrument cluster
5
Gateway (instrument cluster control mod-
ule)
6 Ignition lock
7 Light dial
8 Climate control system blower
9 Steering column lock
10 Climate control system
268
No. Equipment
11 D
iagnost ic data link connecto r, terminal
30
12 Steering column switch module
Right luggage compartment fuse
assignment
Fig. 226 Righ t side of the lu ggage compartment: fuse pan­
e l w ith plastic clip
Fuse panel @ (black)
No. Equipment
1 Luggag e compartm ent lid control module
2 Trailer contro
l module
3 Trailer con trol module
4 Trailer control module
s Elec trom echanica l parking brake
6 E lectronic damping control
7 Electromechanical parking brake
8 Tail lights
9 quattro Sport
10 Tail lights
11 Central locking
system
12 Termina l 30

M N
co
a:
co
,...., \!) 1.1'1
N 1.1'1 ,....,
Fuse panel© (brown)
No. Equipment
1 Luggage compartment lid control module
2 12 V socket, c igarette lighter
3
DCDC converter path 1 or high vo ltage bat-
tery blower (hybrid drive)
4 DCDC converter path 2, DSP amplifier, ra-
dio
7 Electromechanical parking brake
9
Right front doo r (window reg ulator, cen-
tral locking, mirror, switch, lighting)
11 Rear r
ight door (window regulator, switch,
lighting)
12 Cell phone
preparation
Fuse panel ® (black)
No. Equipment
1 Right front seat heating
2 Automatic dimming rearview mirror
3 Instrument panel terminal 30
4 MMI
5 Radio
6 Rearview came
ra
7 Rear window defogger
8 Rear Seat Entertainment
11 AdBlue heating
12 Ad
Blue supply or high voltage battery (hy-
brid drive)
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned out bulbs for you.
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­
moved before you are ab le to get to the bulb.
This applies espec ially to the light bulbs in the
front of you r car which you can only reach
through the engine compartment.
Fuses and bulbs
Sheet metal and bulb holders can have sharp
edges that can cause serious cuts, and parts
must be correctly taken apart and then properly
put back together to help prevent breakage of
parts and long term damage from water that can
enter housings that have not been proper ly re­
sealed .
For your safety, we recommend that you have
your authorized Aud i dealer replace any bulbs for
you, since your dealer has the proper too ls, the
correct bulbs and the expertise .
Gas discharge lamps (Xenon lights )*:
Due to the high e lectrica l voltage, have the bulbs
replaced by a qualified technician. Headlights
with Xenon light can be identif ied by the high
vo ltage sticker.
A WARNING
Contact with high-voltage components of the
electr ical system and improper replacement
of gas discharge (Xenon) headlight bulbs can
cause ser ious personal injury and death.
- Xenon bulbs are pressur ized and can ex-
plode when being changed.
- Changing Xenon lamps requ ires the special
train ing, instructions and equipment.
- Only an authorized Audi dealer or other
qualified workshop should change the bulbs
in gas discharge lamps.
A WARNING "'--
There are parts with sharp edges on the open-
in gs and on the bulb holders that can cause
serious cuts.
- If you are uncertain about what to do, have
the wor k performed by an authorized Aud i
dealer or other qualified workshop. Serious
personal injury may resu lt from improperly
performed work .
(D Tips
-If you must replace the light bulbs yourself,
always remember that the engine compart­
ment of any vehicle is a hazardous area to
work in . Always read and heed all WARN­
INGS¢ page 221 ¢ .&,.
269

Fuses and bulbs
- It is best to as k your au thori zed A udi dealer
whenever yo u need to c hange a bulb .
270