Page 57 of 302

....,
N
r--. > co
rl I.O
"' rl
"' rl
Removing the wiper blade
• Fold the windshield wiper arm away from
the windshie ld .
• Press the locking knob@¢
fig. 50 on the
wiper blade. Hold the wiper blade firm ly.
• Remove the wiper blade in the direction of
the arrow.
In sta ll ing th e wiper blade
• Insert the new wiper blade into the mount
on the wiper arm @until you hear it latch
into place.
• Place the wiper arm back on the windshie ld.
• Turn the service pos ition
off.
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice
each year.
(D Note
- The windshield wiper blades must only
be folded away when in the serv ice posi
tion. Otherw ise, you risk damaging the
paint on the hood or the wi ndshield wip
er motor.
- You should not drive your veh icle or
press the w indshield w iper lever when
the w iper arms are folded away from the
windsh ield . The w indshield w ipers would
move back into their origina l position
and could damage the hood and wind
shield.
- To prevent damage to the windshield
washer system, always loosen w iper
blades that have frozen to the wind
s h ield before turning the wipers on.
- To prevent damage to the wiper blades,
do not apply gasoline, petroleum, thin
ning agents or other solvents on the wip
er blades or near them.
- To prevent damage to the wiper arms or
other components, do not try to move
the windshie ld w ipers by hand .
-
Lights and Visi on 55
@ Tips
-Commercial hot wax such as t he types
used by car washes make it more d ifficult
to clean t he windshie ld.
- Yo u can also use the service position, for
example, if yo u want to protect the
w indshield from icing by using a cover .
- Yo u cannot activate the serv ice position
when the hood is open.
Outside mirror
Adjusting the exterior mirrors
Fi g. 51 Dr iver's door : knob for the ex te ri or mi rrors (ex
a m ple)
T urn the knob to t he des ired pos it io n:
Q/P -In this position, you can adjust the
driver's and front passenge r's exte rior mirrors
by turning the knob i n the desired d irection .
C@ -The mirrors are heated* depend ing on the
outside temperature and driv ing speed .
8 - The exterior mirrors are folded in* .
Front passeng er's exterior mirror tilt
fun ction*
To he lp you see the curb when backing into a
parking space, the surface of the mirror can
be tilted s light ly. The knob must be in the
P pos ition for this to happen .
You can adjust the t ilted mirror surface by
turning the knob i n the desired d irection.
When you move out of reverse and into anoth
er gear, the new m irror position is sto red and
ass igned to the key you are using .
II>
Page 58 of 302

56 Lig hts an d Vi sion
The mirror goes back into its origina l position
once you drive forward faster than 9 mph
(15 km/h) or turn the ign ition
off.
Folding mirr ors in and out
To fold the mirrors in w ith the knob, turn the
knob in the 8 pos ition.
To fold the m irrors out, turn the knob in the
q or
P or O position .
You can set in the MMI if the mirrors shou ld
fold in when locking the vehicle or not
c::> page 36. When you lock the vehicle , the
mirrors fold in . When you sta rt the ignit ion,
the m irrors fold out .
A WARNING
Curved mirror s urfaces (convex or asphe
ric*) enlarge the field of vision. However,
they make objects in the mirror appear sma ller and farther away . Your may esti
mate incorrectly when you use these m ir
rors to gauge your d istance from the
veh icles behind you when changing lanes -
accident risk!
@ Note
- For vehicles with power folding exterior
mirrors*: If the m irror housing was
moved by outside forces (such as an im
pact when maneuvering), you must use
the power folding function to fold the mirro r all the way out. You will hear a
l oud noise when the m irrors are latched
back in place. The mir ror housi ng must
not be moved back into place by hand
because this would affect the mirror
mechan ism.
- Applies to vehicles witho ut power fold
i ng exter ior mirrors: If the mirror hous
ing was moved by outside forces (suc h as
in impact during maneuvering), you
must move the m irror housing back into
place by hand.
- If you wash the vehicle in an automatic
car wash, yo u m ust fold the e xterior m ir
r o rs in to reduce the risk of damage to
the m irrors. Never fold power fo ld ing ex-
-
terior mirrors by hand . On ly fold them in
and out using the power controls.
(D Tips
If t he power ad justmen t fails, bot h mir
ro rs can be adjusted by hand by pressing
on the edge of the mirror surface.
Dimming the mirrors
Your vehicle is equipp ed with a manual or au
tomatic* dimming rearview mirror.
F ig . 52 A uto matic dimmin g rea rv iew mi rro r*
Manu al dimming rearv iew mirro r
.. Pull the lever on the bottom of the m irror
back .
Automat ic dimming r earview mirror*
.. Press the b utton @. The ind icator light @
turns on . The rearview and driver's exterior*
mirrors dim a utomatically when light shines
on them, for example from headlights on a
veh icle to the rear .
A WARNING
Electrolyte fluid can leak from automatic
d imm ing mirrors if the glass is b roken .
E le ctro lyte fluid can irr itate skin, eyes and
a irways.
- Repeated or long-te rm exposure to e lec
t rolyte f luid can lead to ir ritat io n of the
a ir ways, especi ally in peo ple wit h asthma
or other respiratory co nd it ions. T ake
deep breaths immediately after leaving
the vehicle or, if this is not possib le,
open all of the doo rs and windows as
wide as possible.
Page 59 of 302

....,
N
r--. > co
rl I.O
"' rl
"' rl
-If electrolyte fluid enters the eyes, f lush
them thoroughly with a large amount of
clean water for at least 15 minutes and
then seek medical attention .
- If electrolyte fluid comes into contact
with the skin, flush the affected area
with clean water for at least 15 m inutes
and then clean with soap and water and
seek medical attention. Clean affected cl othing and shoes tho roughly before
wearing aga in.
- If the fluid was swallowed and the per
son is conscious, f lush the mou th wi th
water for at least 15 minutes. Do not in duce vomiting unless this is recommend
ed by medical professionals . Seek medi
cal attention immediately .
(D Note
If the glass on an automatic dimming m ir
ror breaks, electroly te can leak o ut. This
liquid damages plastic surfaces . Clean this
liquid as quickly as poss ible with a wet
sponge.
@ Tips
- If the light reaching the rearv iew mirror
i s obstructed, the automatic dimming
mirror will not function correctly,
- The automatic dimming mirro rs do not
dim when the interior lighting is turned
on or the reverse gear is selected.
Digital compass
Switching the compass on and off
Applies to vehicles: with d ig ital compass
Fig. 53 Rearview m irro r: d ig ital compass activated
Lights and Visi on 5 7
.. To turn the compass on or off, press the but
ton @until the compass in the mirror ap
pears or d isappears.
T he digita l compass on ly wor ks when the igni
tion is turned on. The di rections are indicated
with abbreviat ions:
N (north), NE (northeast),
E (east), SE (southeast),
S (south) , SW (south
west) ,
W (west), NW (northwest).
You must recalibrate the compass if it does not display the correct direction
¢ page 58,
Calibrating the compass.
(D Tips
To prevent inaccurate compass readings,
do not bring any remote contro ls, e lectri
ca l devices or metallic objects near the
mirror.
Adjusting the magnetic zone
App lies to vehicles: wit h digital compass
The magnetic zone must be adjusted correctly
for the compass to read accurately.
F ig . 5 4 North A merica: mag net ic zo ne map
.. Press and hold the button @ i:> page 5 7,
fig. 53 until the number of the magnetic
zone appears in the rearv iew mirror.
Page 60 of 302
58 Light s a nd V is ion
• Press the button @repeated ly to select the
correct magnetic zone. The selection mode
turns off after a few seconds.
Calibrating the compass
Applies to vehicles: with dig ital compass
You must recalibrate the compass if it does
not display the correct direction .
• Press and ho ld the button @~ page 57,
fig . 53
until a C appears in the rearview mir
ror.
• Drive in a circle at about 5 mph ( 10 km/h)
until a direction is disp layed in the rearview
mirror .
A WARNING
- To avoid endangering yourself and other
dr ivers, calibrate the compass in an area
whe re there is no traffic.
- The digital compass should only be used
as an or ientat ion aid. If you want to
check the compass while dr iving, you
must still pay attention to traff ic, the
road, the weather and any other possible
hazards.
Page 61 of 302

M N ,....
> co ,...., \!) ..,.,
,...., ..,., ,....,
Seats and storage
General information
Important information
A WARNING
Refer to the chapter Driving Safely
¢ page 126, Driving safety for important
information, tips, suggestions and warn
ings that you should read and follow for
your own safety and the safety of your pas sengers.
The safety belts and the airbag system con
only provide maximum protection if the front
seats ore correctly adjusted.
There are various ways of adjusting the front
seats to provide safe and comfortable support
for the driver and the front passenger. Adjust
your seat properly so that :
- you can easily and quick ly reach all the
switches and controls in the instrument
panel
- your body is properly supported thus reduc
ing physical stress and fatigue
- the safety be lts and airbag system can offer
maximum protection
¢ page 146.
In the following sections, you will see exactly
how you can best adjust your seats .
There are special regulations and instructions
for installing a child seat on the front pas
senger's seat. Always follow the information
regarding chi ld safety provided in
¢ page 169, Child Safety.
A WARNING
Incorrect seating position of the driver and
all other passengers can result in serious
personal injury.
- Always keep your feet on the floor when
the vehicle is in motion -never put your
feet on top of the instrument panel, out
of the window or on top of the seat cush ion. This applies especially to the passen-
Seats and storage 59
gers. If your seating position is incorrect,
you increase the risk of injury in the case
of sudden braking or an accident. If the
airbag inflates and the seating position is incorrect, this could result in pe rsonal
injury or even death.
- It is important for both the driver and
front passenger to keep a distance of at
least 10 inches (25 cm) between them
selves and the steering wheel and/or in
strument panel. If you're sitting any
closer than this, the airbag system can
not protect you properly. In addition, the
front seats and head restraints must be
adjusted to your body height so that they
can give you maximum protect ion.
- Always try to keep as much distance as
possible between yourself and the steer
ing wheel or instrument panel.
- Do not adjust the driver's or front pas
senger's seat whi le the vehicle is moving.
Your seat may move unexpectedly, caus
ing sudden loss of veh icle control and
personal injury. If you adjust your seat
while the veh icle is moving, you are out
of posit ion.
Driver's seat
The correct seat position is important for safe
and relaxed driving .
We recommend that you adjust the dr iver's
seat in the follow ing manner:
"" Adjust the seat in fore and aft direction so
that you can easily push the pedals to the
floor wh ile keeping your knees slightly bent
¢ &, on page 59.
"" Adjust the backrest so that when you sit
w ith your back against the backrest, you can
still hold the top of the steering wheel.
""For adjustab le head restra ints: adjust the
head restraint so the uppe r edge is as even
as possible with the top of your head. If that
is not possible , try to adjust the head re
straint so that it is as close to this position ..,_
•
Page 62 of 302

60 Seats and st o rage
as possible <:!> page 62. Move the head re
straint so that it is as close to the back of
the head as possible.
A WARNING
Never place any objects in the driver's foot
we ll. An object could get into the pedal
area and interfere with pedal function . In
case of sudden b raking o r an accident, you
would not be ab le to brake o r acce le rate.
Front passenger's seat
Always move the front passenger seat into the rearmost position .
To avoid contact with the airbag while it is de
p loying, do not sit any closer to the instru
ment panel than necessary and always wear
the three-point safety belt provided adjusted
correctly . We recommend that you adjust the
passenger's seat i n the fol lowing ma nner:
,,. Bring the backres t up to an (a lmost) upr ight
pos it ion.
D o not ride w ith the seat reclined .
,,. For adjustable head restraints : adjust the
head res traint so the upper e dge is as even
as possib le w ith the top o f your head .
If tha t
is not possib le, try to adjust the head re
straint so that it is as close to th is position
as possible
<:!> page 62 . Move the head re
stra int so that it is as close to the back of
the head as possible.
,,. Place your feet on the floor in front of the
passenge r's seat .
Front seats
Manual seat adjustment
Applies to veh icles: w ith manually adjustab le seats
F ig. 55 Fro nt sea t: man ual seat adjustment
(D-Moving the seat forward/back : pull the
l ever and slide t he seat.
@ -Le ngt hening/shortening t he upper thigh
s u pport*: lift the handle.
@ -Adjust ing the angle of the seat sur face *:
pull/press the lever .
@-Adjust ing the lumbar support*: p ress the
button in the desired direction .
®-Moving the seat up/down : pull/press the
lever .
®-Adjust ing the backrest angle : turn the ad
j usting wheel.
A WARNING
- O nly ad just t he front seat with when the
veh icle is stationary. O therw ise, this in
creases t he risk of an accid ent
- Exerc ise caution when ad justing the seat
he ight . Ad justing the seat care less ly o r
wit hout checking can p in ch hands and
fi ngers .
- The front seat back rests must b e not tilt
ed too far ba ck when drivi ng, be ca use
this affects the effe ctiveness of the s afe
ty belts and airbag system, which in
creases the risk of inju ry .
- T o reduce the ris k of injury dur ing s udden
b raking or in a collision, the d rive r and
front passenger sho uld not have thei r
backrests in the reclined position while
Page 63 of 302

....,
N
r--. > co
rl I.O
"' rl
"' rl
driving or riding. The safety belts and air
bag system can provide the greatest pro
tection possible when the backrests are
in the upright position and the safety
belts are worn correctly. The more a
backrest is reclined, the greater the risk
of inju ry due to an incorrect seating posi
tion and safety belt position .
Power seat adjustment
Applies to vehicles: with power adjustable seats
Fig. 56 Fr ont seat: power seat adjustment
@ -Adjusting the lumbar support: press the
button in the desired d irection.
@ -Moving the seat up/down : press the but
ton up/down. To adjust the front seat cushion,
press the front button up/down. To adjust the
rear seat cushion, press the rear button up/
down .
@-Moving the seat forward/back: press the
button forward/back.
© -Adj usting the backrest angle: press the
button forward/back.
@ -Lengthening/shortening the upper thigh
support*: lift the handle.
A WARNING ,-
- Only adjust the front seat w ith when the
vehicle is stationary. Otherwise, this in
creases the r isk of an accident
- The power adjustment for the front seats
also works with the ignition switched off
or with the ignition key removed. For this
reason, ch ildren should never be left un
attended in the vehicle -they co uld be in
jured!
Seats and storage 61
-Exercise caution when adjusting the seat
height. Unsupervised or careless seat ad
justment can pinch fingers or hands
causing injuries.
- The front seat backrests must be not t ilt
ed too far back when driving, because
this affects the effective ness of the safe
ty belts and airbag system, which in
creases the risk of injury.
- To reduce the risk of injury dur ing sudden
braking or in a co llision, the driver and
front passenger shou ld not have their
backrests in the reclined position while
driving or rid ing. The safety be lts and air
bag system can provide the greatest pro
tection possible when the backrests are in the upright position and the safety
be lts are worn correctly. The more a
backrest is reclined, the greater the risk
of injury due to an incorrect seating posi
tion and safety belt position.
Easy seat entry
Easy seat entry makes it easier to get into the
back seats.
Fig. 57 Driver's seat: easy seat entry controls
~ N 0 > m a,
....
l1l 0 > m a,
Fig . 58 Easy seat entry operation, seat returning to the
origina l pos it ion w ith seat memory
Ill>
Page 64 of 302

62 Seats and storage
Folding the front seat backrests forward
.,. Pull the handle@ ¢fig. 57forward.
.,. Fold the backrest forward until it locks into
place and then slide the seat all the way for
ward using the backrest @.
Folding the front seat backrests back
.,. Slide the seat all the way back using the
backrest @
c;> fig. 58.
.,. Fold the backrest back until it locks into
place @.
The seat will return to its original position af
ter using easy seat entry .
A WARNING -
The front seat backrests must always be
locked in lace while driving for safety rea
sons.
- When using easy seat entry, the seat
must always slide all the way back when
returning it to its original position. Oth
erwise, the set will not be able to lock in
place. Only drive once the seat is locked
into place.
@ Tips
If the seat will not lock in place after using
easy seat entry, slide the seat all the way
back until it stops. Then ad just the seat to
the desired position.
Front center armrest
Applies to vehicles: with front center armrest
The center armrest can be adjusted to several
levels.
Fi g. 59 Armrest between th e driver 's/fro nt passe nge r's
seats
.,. To adjust the angle, raise the armrest
c;> fig. 59 notch by notch .
.,. To bring the armrest back down, raise it out
of the top notch and fold it back down. Then
lift the armrest to the desired position, if
necessary .
P lease note that the driver's ability to move
his or arm may be restricted when the armrest
is folded down. Because of th is, the armrest
should not be folde d down during city driv ing.
The armrest can slide forward and back.
T here is a storage compartment under the
armrest .
Head restraints
Front head restraints
Applies to vehicles: wit h adjusta ble head restra ints
Fig. 60 Front seat: ad justing standard head restraints
Applies to vehicles with super sport seats* (no
illustration): The head restraints are integrat
ed in the backrest and cannot be adjusted.
Adjust the head restraints so the upper edge
is as even as possible with the top of your
head. If that is not possible, try to adjust as
close to this position as possible .
.,. To move the head restraint up or down, slide
it until it locks into place
c;>fig . 60.
Refer to
c;> page 130, Proper adjustment of
head restraints
for guidelines on how to ad
ju st the height of the front head restraints to
s ui t the occupant's body size.