2014 NISSAN TEANA Center

EM-124
< PRECAUTION >[VQ35DE]
PRECAUTIONS
• When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is specified,
do exactly as specified.
• Replace with new gasket, packing, oil seal or O-ring.
• Thoroughly wash, clean, and air-blow each part. Carefully check oil or coolant passages for any restriction and blockage.
• Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust. Before assembly, oil sliding surfaces well.
• Release air within route after draining coolant.
• Before starting engine, apply fuel pressure to fuel li nes with turning ignition switch ON (with engine stopped).
Then make sure that there are no leaks at fuel line connections.
• After repairing, start engine and increase engine speed to check coolant, fuel, oil, and exhaust systems for leakage.
Parts Requiring Angular TighteningINFOID:0000000009460520
• Use an angle wrench for the final tightening of the following engine parts:
- Cylinder head bolts
- Main bearing cap bolts
- Connecting rod cap nuts
- Crankshaft pulley bolt (No angle wrench is required as the bolt flange is provided with notches for angular
tightening)
• Do not use a torque value for final tightening.
• The torque value for these parts are for a preliminary step.
• Ensure thread and seat surfaces are clean and coated with engine oil.
Precaution for Liquid GasketINFOID:0000000009460521
REMOVAL OF LIQUID GASKET
• After removing the bolts and nuts, separate the mating surface and remove the liquid gasket using Tool (A).
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to lightly tap (1) the cutter where the liquid gasket is applied. Use a
plastic hammer to slide (2) the cutter by tapping on the side.
CAUTION:
Do not damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using a scraper, remove the old liquid gasket adhering to the gasket application surface and the mating surface.
• Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts, and bolt holes.
2. Thoroughly clean the gasket application surface and the mating surface and remove adhering moisture, grease and foreign
materials.
3. Attach the liquid gasket tube to the tube presser. Use Genuine Silicone RTV Seal ant or equivalent. Refer to
GI-21, "Recommended Chemi cal Products and Sealants"
.
Tool Number: KV10111100 (J-37228)
AWBIA1249GB
PBIC0003E
Revision: November 20132014 Altima NAM

DRIVE BELTSEM-135
< PERIODIC MAINTENANCE > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
3. While securely holding the hexagonal part in pulley center of
drive belt auto-tensioner, move in the direction of arrow (loosen-
ing direction of drive belt auto-tensioner) using suitable tool.
WARNING:
Avoid placing hand in a locat ion where pinching may occur
if the holding tool accidentally comes off.
CAUTION:
Do not loosen the drive belt auto-tensioner pulley bolt. (do
not turn it counterclockwise. ) If turned counterclockwise,
the complete drive belt auto-t ensioner must be replaced as
a unit, including pulley.
4. Insert a rod approximately 6 mm (0.24 in) in diameter through the rear of drive belt auto-tensioner into retain ing boss to lock drive belt auto-tensioner pulley.
NOTE:
Leave drive belt auto-tensioner pulley arm locked until belt is installed again.
5. Loosen drive belt and then remove it from the other pulleys.
INSTALLATION
1. Install the drive belt onto all of the pulleys.
CAUTION:
Confirm belts are completely set on the pulleys.
2. Release drive belt auto-tensioner, and apply tension to belt. WARNING:
Avoid placing hand in a location wh ere pinching may occur if the holding tool accidentally comes
off.
CAUTION:
Do not loosen the auto-te nsioner pulley bolt. (Don't turn it counterclockwise. If turned counter-
clockwise, the complete auto-tensioner mu st be replaced as a unit, including pulley.
3. Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
4. Confirm tension of belt at indicator is within the possible use range. Refer to EM-19, "Checking Drive
Belts".
5. Install the fender protector side cover RH. Refer to EXT-26, "FENDER PROTECTOR : Removal and
Installation".
6. Install the front RH wheel and tire. Refer to WT-55, "Adjustment"
.
Removal and Installation of Drive Belt Auto-tensionerINFOID:0000000009460532
AWBIA1204GB
Revision: November 20132014 Altima NAM

CAMSHAFT VALVE CLEARANCEEM-141
< PERIODIC MAINTENANCE > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
VALVE ADJUSTING
CAUTION:
Adjust valve clearance while engine is cold.
NOTE:
• Perform adjustment by selecting the correct head thicknes s of the valve lifter (adjusting shims are not used).
• The specified valve lifter thickness is the dimension at normal temperatures. Ignore dimensional differences
caused by temperature. Use spec ifications for hot engine condition to confirm valve clearances.
1. Remove the camshaft. Refer to EM-194, "Removal and Installation"
.
2. Remove the valve lifter that was measur ed as being outside the standard specifications.
3. Measure the center thickness of the removed lifter with a micrometer, as shown.
4. Use the equation below to calculate the replacement valve lifter thickness.
Valve lifter thickness calculation equation: t = t1 + (C1 - C2)
t = thickness of the replacement lifter
t1 = thickness of the removed lifter
C1 = measured valve clearance
C2 = standard valve clearance
• The thickness of the new valve lifter can be identified by the
stamp mark on the reverse side (inside the lifter).
• Available thickness of the valve lifter (factory setting):
7.88 - 8.40 mm (0.3102 - 0.3307 in), in 0.02 mm (0.0008 in)
increments, in 27 sizes (intake / exhaust). Refer to EM-249,
"Cylinder Head".
5. Install the selected replacement valve lifter.
6. Install the camshaft. Refer to EM-194, "Removal and Installation"
.
7. Rotate the crankshaft a few turns by hand.
8. Confirm that the valve clear ances are within specification.
9. After the engine has been run to full operating temperat ure, confirm that the valve clearances are within
specification.
* Approximately 80 °C (176 °F)
SEM754G
SEM755G
Standard Valve Clearance Cold Hot* (reference data)
Intake 0.26 - 0.34 mm (0.010 - 0.013 in) 0.304 - 0.416 mm (0.012 - 0.016 in)
Exhaust 0.29 - 0.37 mm (0.011 - 0.015 in) 0.308 - 0.432 mm (0.012 - 0.017 in)
Revision: November 20132014 Altima NAM

EM-166
< REMOVAL AND INSTALLATION >[VQ35DE]
FUEL INJECTOR AND FUEL TUBE
• Do not reuse O-rings.
• Upper and lower O-rings are different. Be careful not to confuse them.
• Handle O-ring with bare hands. Do not wear gloves.
• Lubricate O-ring with new engine oil.
• Do not clean O-ring with solvent.
• Check that O-ring and its mating pa rt are free of foreign material.
• When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to
twist or stretch O-ring. If O-ring was stretc hed while it was being attached, do not insert it
quickly into fuel tube.
• Insert O-ring straight into fu el injector. Do not twist it.
3. Install fuel injector to fuel tube as follows:
a. Insert clip (3) into clip groove (F) on fuel injector (5).
• Insert clip so that protrusion (E ) of fuel injector matches cutout
(C) of clip.
CAUTION:
• Do not reuse O-rings.
• Do not reuse clip. Replace it with new one.
• Be careful to keep clip from interfering with O-ring. If interference occurs, replace O-ring.
b. Insert fuel injector into fuel tube (1) with clip attached. • Insert it while matching it to the axial center.
• Insert fuel injector so that protrusion (A) of fuel tube matches
cutout (B) of clip.
• Check that fuel tube flange (G) is securely fixed in flange fixing
groove (D) on clip.
c. Check that installation is complete by checking that fuel injector does not rotate or come off.
• Check that protrusions of fuel injectors and fuel tubes are
aligned with cutouts of clips after installation.
4. Install fuel tube and fuel injector assembly to intake manifold. CAUTION:
Be careful not to let tip of injector nozzle come in contact with other parts.
• Tighten bolts in two steps in numerical order as shown.
5. Connect fuel injector harness.
6. Install intake manifold collector. Refer to EM-146, "Removal and Installation"
.
7. Connect quick connector between fuel feed hose and fuel tube connection with the following procedure:
a. Check no foreign substances are deposited in and around fuel tube and quick connector, and no damage on them.Fuel tube side : Black
Nozzle side : Green
(2) : O-ring (black)
(4) : O-ring (green)
JPBIA1959ZZ
: Engine front
1st step : 10.1 N·m (1.0 kg-m, 7 ft-lb)
2nd step : 22.0 N·m (2.2 kg-m, 16 ft-lb)
JPBIA1715ZZ
Revision: November 20132014 Altima NAM

FUEL INJECTOR AND FUEL TUBEEM-167
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
b. Thinly apply new engine oil around fuel tube from tip end to spool end.
c. Align center to insert quick connector straightly into fuel tube. • Insert quick connector (1) to fuel tube until top spool (2) is
completely inside quick connector, and 2nd level spool (3)
exposes right below quick connector.
CAUTION:
• Do not reuse O-ring.
• Hold (A) position as shown when inserting fuel tube into quick connector.
• Carefully align center to avoid inclined insertion to pre-
vent damage to O-ring inside quick connector.
• Insert until you hear a “click” sound and actually feel the engagement.
• To avoid misidentification of enga gement with a similar sound, be sure to perform the next step.
d. Pull quick connector by hand holding position. Check it is completely engaged (connected) so that it does
not come out from fuel tube.
e. Install quick connector cap (3) to quick connector.
• Install quick connector cap with arrow (A) on surface facing indirection of quick connector (fuel feed hose side).
CAUTION:
If quick connector cap cannot be installed smoothly, quick
connector may have not been installed correctly. Check
connection again.
f. Secure fuel feed hose to clamp of quick connector cap.
8. Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
Make sure there is no fuel leakage at connections as follows:
1. Apply fuel pressure to fuel lines by turning i gnition switch ON (with engine stopped). Then check for fuel
leaks at connections.
2. Start the engine and rev it up and check for fuel leaks at connections. WARNING:
Do not touch engine immediately after stopping as engine is extremely hot.
NOTE:
Use mirrors for checking on connections out of the direct line of sight.
• Perform procedures for “Throttle Valve Closed Position Learning” after finishing repairs. Refer to EC-
682, "Work Procedure".
• If electric throttle control actuator is replaced, perform procedures for “Idle Air Volume Learning” after
finishing repairs. Refer to EC-683, "Work Procedure"
.
(B) : Installed condition
: Upright insertion
(1) : Fuel feed hose
(2) : Fuel tube
(B) : Upper view
JPBIA0275ZZ
JPBIA0039ZZ
Revision: November 20132014 Altima NAM

EM-176
< REMOVAL AND INSTALLATION >[VQ35DE]
FRONT TIMING CHAIN CASE
Do not damage the ring gear teeth, or the signal
plate teeth behind the ring gear, when installing
Tool.
22. Remove the crankshaft pulley as follows:
a. Loosen crankshaft pulley and locate bolt seating surfac e at 10 mm (0.39 in) from its original position.
b. Position a pulley puller at recess hole of crankshaft pulley to remove crankshaft pulley.
CAUTION:
Do not use a puller claw on crankshaft pulley periphery.
23. Remove the power steering pump. Refer to ST-38, "Removal and Installation"
.
24. Remove the lower oil pan. Refer to EM-156, "Removal and Installation (Lower Oil Pan)"
.
25. Remove upper oil pan bolts (1) and (2) as shown. Refer to EM-
157, "Removal and Installation (Upper Oil Pan)".
26. Remove the generator. Refer to CHG-32, "Removal and Installation"
.
27. Disconnect the A/C tubes from the A/C compressor and position aside. Refer to HA-23, "Recycle Refriger-
ant".
28. Remove the A/C compressor bolts and the A/C compressor. Refer to HA-30, "COMPRESSOR : Removal
and Installation".
29. Remove the generator bracket. Refer to CHG-32, "Removal and Installation"
.
30. Support the engine with suitable jack and remove the RH engine insulator, mount and torque rod. Refer to EM-220, "Removal and Installation"
.
31. Disconnect the oil pressure switch harness connector.
32. Disconnect the intake valve timing control solenoid valve harness connector.
33. Remove the intake valve timing control solenoid valve cover bank 1 (RH) (A) and intake timing control solenoid valve cover
bank 2 (LH) (B).
• Loosen the intake valve timing control solenoid valve cover bolts in the reverse order as shown.
CAUTION:
The shaft in the intake valve ti ming control solenoid valve
cover is inserted into the center hole of the intake cam-
shaft sprocket. Remove the in take valve timing control
solenoid valve cover by pull ing straight out until the
intake valve timing control so lenoid valve cover disengages from the camshaft sprocket.
34. Remove the drive belt auto-tensioner. Refer to EM-134, "Removal and Installation"
.
35. If necessary, remove the water pump cover.
EMQ0477D
WBIA0259E
(C) : Dowel pin hole
JPBIA1639ZZ
Revision: November 20132014 Altima NAM

EM-196
< REMOVAL AND INSTALLATION >[VQ35DE]
CAMSHAFT
1. Before installation, remove any old Silicone RTV Sealant from
component mating surfaces using a scraper.
• Remove the old Silicone RTV Sealant from the bolt holes and
threads.
• Do not scratch or damage the mating surfaces.
2. Before installing the front cam bracket, remove the old Silicone RTV Sealant from the mating surface using a scraper.
• Do not scratch or damage the mating surface.
3. Turn the crankshaft until No. 1 piston is set at TDC on the com- pression stroke.
• The crankshaft key should line up with the right bank cylinder
center line as shown.
4. Install camshaft chain tensioners on both sides of cylinder head. Refer to EM-182, "Removal and Installation"
.
CAUTION:
Do not reuse O-rings.
5. Install valve lifters, if removed. NOTE:
Install them in original positions.
SEM161F
SEM892E
SEM532G
SEM444G
Revision: November 20132014 Altima NAM

EM-208
< REMOVAL AND INSTALLATION >[VQ35DE]
CYLINDER HEAD
7. Remove cylinder heads and gaskets.
• Discard the cylinder head gaskets and use new gaskets forinstallation.
INSTALLATION
1. Turn the crankshaft until No. 1 piston is set at TDC on the com- pression stroke.
• The crankshaft key should line up with the right bank cylinder
center line as shown.
2. Install new gaskets on the cylinder heads.
3. Inspect the cylinder head bolts before installing the cylinder heads. CAUTION:
Cylinder head bolts are tighte ned by degree rotation tight-
ening method. Whenever the size difference between d1
and d2 exceeds the limit, replace the bolts with new ones.
• Lubricate threads and seat surfaces of the bolts with new
engine oil.
SEM863E
SEM532G
SEM445G
Limit (d1 - d2) : 0.11 mm (0.0043 in)
SEM957E
Revision: November 20132014 Altima NAM