2014 NISSAN TEANA height

SERVICE DATA AND SPECIFICATIONS (SDS)EM-247
< SERVICE DATA AND SPECIFICATIONS (SDS) [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
Spark PlugINFOID:0000000009460586
SPARK PLUG
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
Intake Manifold INFOID:0000000009460587
INTAKE MANIFOLD
Unit: mm (in)
Exhaust ManifoldINFOID:0000000009460588
EXHAUST MANIFOLD
Unit: mm (in)
CamshaftINFOID:0000000009460589
CAMSHAFT
Unit: mm (in)
Tension of drive belt Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Make
DENSO
Standard type* FXE22HR11
Gap Standard 1.1 (0.043)
Items Limit
Surface distortion Intake manifold 0.1 (0.004)
Items Limit
Surface distortion Exhaust manifold 0.3 (0.012)
Items Standard Limit
Camshaft journal oil clearance No. 1 0.045 - 0.086 (0.0018 - 0.0034)
0.15 (0.0059)
No. 2, 3, 4 0.035 - 0.076 (0.0014 - 0.0030)
Camshaft bracket inner diameter No. 1 26.000 - 26.021 (1.0236 - 1.0244) —
No. 2, 3, 4 23.500 - 23.521 (0.9252 - 0.9260) —
Camshaft journal diameter No. 1 25.935 - 25.955 (1.0211 - 1.0218) —
No. 2, 3, 4 23.445 - 23.465 (0.9230 - 0.9238) —
Camshaft end play 0.115 - 0.188 (0.0045 - 0.0074) 0.24 (0.0094)
Camshaft cam height (A) Intake 45.475 - 45.665 (1.7904 - 1.7978)
0.2 (0.008)*
1
Exhaust 45.485 - 45.675 (1.7907 - 1.7982)0.2 (0.008)*1
Camshaft runout [TIR*2]Less than 0.02 (0.0008) 0.05 (0.0020)
Camshaft sprocket runout [TIR*
2] Less than 0.15 (0.0059) —
Revision: November 20132014 Altima NAM

SERVICE DATA AND SPECIFICATIONS (SDS)EM-249
< SERVICE DATA AND SPECIFICATIONS (SDS) [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
*: Always check with the Parts Department for the latest parts information.
Cylinder HeadINFOID:0000000009460590
CYLINDER HEAD
Unit: mm (in)
VALVE DIMENSIONS
820C 8.20 (0.3228)
822C 8.22 (0.3236)
824C 8.24 (0.3244)
826C 8.26 (0.3252)
828C 8.28 (0.3260)
830C 8.30 (0.3268)
832C 8.32 (0.3276)
834C 8.34 (0.3283)
836C 8.36 (0.3291)
838C 8.38 (0.3299)
840C 8.40 (0.3307)
Identification (stamped) mark* Thickness
SEM758G
Items Standard Limit
Head surface distortion Less than 0.03 (0.0012) 0.1 (0.004)
Normal cylinder head height (H) 126.3 - 126.5 (4.972 - 4.980) —
Spark plug tube installation height 37.7 - 39.1 (1.484 - 1.539) —
PBIC0924E
Revision: November 20132014 Altima NAM

EM-250
< SERVICE DATA AND SPECIFICATIONS (SDS) [VQ35DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
Unit: mm (in)
VALVE OIL SEAL
Unit: mm (in)
VA LV E G U I D E
Unit: mm (in)
Valve head diameter (D)Intake 36.6 - 36.9 (1.441 - 1.453)
Exhaust 30.2 - 30.5 (1.189 - 1.201)
Va l v e l e n g t h ( L ) Intake 97.13 (3.8240)
Exhaust 94.67 (3.7272)
Valve stem diameter (d) Intake 5.970 - 5.980 (0.2350 - 0.2354)
Exhaust 5.962 - 5.970 (0.2347 - 0.2350)
Valve seat angle α Intake
45°15 ′ - 45 °45 ′
Exhaust
Valve margin (T) Intake 1.15 - 1.45 (0.0453 - 0.0571)
Exhaust 1.45 - 1.75 (0.0571 - 0.0689)
Valve margin (T) limit More than 0.5 (0.020)
Valve stem end surface grinding limit Less than 0.2 (0.008)
SEM188
Description Standard
Valve oil seal installation height 14.3 - 14.9 (0.563 - 0.587)
Items Standard Oversize (Service) [0.2 (0.008)]
Valve guide Outer diameter 10.023 - 10.034 (0.3946 - 0.3950) 10.223 - 10.234 (0.4025 - 0.4029)
Inner diameter (Finished size) 6.000 - 6.018 (0.2362 - 0.2369)
Cylinder head valve guide hole diameter 9.975 - 9.996 (0.3927 - 0.3935) 10.175 - 10.196 (0.4006 - 0.4014)
Interference fit of valve guide 0.027 - 0.059 (0.0011 - 0.0023) Items Standard Limit
SEM950E
Revision: November 20132014 Altima NAM

SERVICE DATA AND SPECIFICATIONS (SDS)EM-251
< SERVICE DATA AND SPECIFICATIONS (SDS) [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
VA LV E S E AT
Unit: mm (in)
*:Machining data Valve guide clearance
Intake 0.020 - 0.053 (0.0008 - 0.0021) 0.08 (0.0031)
Exhaust 0.040 - 0.073 (0.0016 - 0.0029) 0.01 (0.004)
Valve deflection Intake — 0.24 (0.0094)
Exhaust — 0.28 (0.0110)
Projection length (L) 12.6 - 12.8 (0.496 - 0.504)
Items Standard Oversize (S ervice) [0.5 (0.02)]
Cylinder head seat recess diameter (D) Intake (A) 38.000 - 38.016 (1.4961 - 1.4967) 38.500 - 38.516 (1.5157 - 1.5164)
Exhaust (B) 31.600 - 31.616 (1.2441 - 1.2447) 32.100 - 32.116 (1.2638 - 1.2644)
Valve seat outer diameter Intake 38.097 - 38.113 (1.4999 - 1.5005) 38.597 - 38.613 (1.5196 - 1.5202)
Exhaust 31.680 - 31.696 (1.2472 - 1.2479) 32.180 - 32.196 (1.2669 - 1.2676)
Valve seat interference fit Intake 0.081 - 0.113 (0.0032 - 0.0044)
Exhaust 0.064 - 0.096 (0.0025 - 0.0038)
Height (h) Intake (A) 5.9 - 6.0 (0.232 - 0.236) 5.05 - 5.15 (0.1988- 0.2028)
Exhaust (B) 5.9 - 6.0 (0.232 - 0.236) 4.95 - 5.05 (0.1949 - 0.1988)
Contacting width (W)* Intake (A) 1.0 - 1.4 (0.0394 - 0.0551)
Exhaust (B) 1.2 - 1.6 (0.0472 - 0.0630)
Cylinder head seat recess depth (H) 6.0 (0.236)
Depth (L) Intake (A) 41.16 - 41.76 (1.6205 - 1.6441)
Exhaust (B) 41.09 - 41.69 (1.6177 - 1.6413)
AWBIA0033GB
SEM621F
Revision: November 20132014 Altima NAM

EM-252
< SERVICE DATA AND SPECIFICATIONS (SDS) [VQ35DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
VALVE SPRING
Unit: mm (in)
Cylinder BlockINFOID:0000000009460591
CYLINDER BLOCK
Unit: mm (in)
Items Standard
Free height 47.07 mm (1.8531 in)
Installation height 37.0 mm (1.457 in)
Installation load 166 - 188 N (16.9 - 19.2 kg, 37 - 42 lb)
Height during valve open 27.2 mm (1.071 in)
Load with valve open 373 - 421 N (38.0 - 42.9 kg, 84 - 95 lb)
Items Limit
Squareness Less than 2.0 (0.079)
Surface distortion Standard Less than 0.03 (0.0012)
Limit 0.10 (0.0039)
Main bearing housing inner diameter Standard 63.993 - 64.017 (2.5194 - 2.5203)
Cylinder bore Inner diameter StandardGrade No. 1 95.500 - 95.510 (3.7598 - 3.7602)
Grade No. 2 95.510 - 95.520 (3.7602 - 3.7606)
Grade No. 3 95.520 - 95.530 (3.7606 - 3.7610)
Wear limit 0.20 (0.0079)
Out-of-round Limit0.015 (0.0006)
Taper (Difference between A and C) 0.015 (0.0006)
JPBIA2238GB
Revision: November 20132014 Altima NAM

EX-6
< REMOVAL AND INSTALLATION >[QR25DE]
EXHAUST SYSTEM (QR25DE)
Removal and Installation
INFOID:0000000009460685
WARNING:
• Perform the procedure with the exhaust system fu lly cooled down because the system will be hot
just after the engine is turned off.
• Be careful not to cut your hand on the insulator edges.
CAUTION:
• Use Genuine NISSAN exhaust system parts or equival ent, which are specifically designed for heat
resistance, corrosion resistance, and shape.
REMOVAL
Remove exhaust system components using power tool.
• Remove heated oxygen sensor using Tool as needed.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Always replace exhaust gaskets with new ones when reassembling.
• Before installing a new heated oxygen sensor, cl ean and lube the exhaust tube threads using suit-
able tool.
• Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a co ncrete floor; install a new one.
• Do not over-tighten the heated oxygen sensor. Doing so may damage the heated oxygen sensor,
resulting in the MIL coming on.
• If any mounting insulator is badly deformed, repair or replace it. If deposits such as mud pile up on
the mounting insulator, clean and inspect them.
• When installing the insulator avoid large gaps or interference between the insulator and each
exhaust pipe.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust gas leaks.
• Temporarily tighten the exhaust manifold side nuts and the vehicle side bolts. Check each part for
any interference, and then tighten th e nuts and bolts to specification.
• When installing each mounting rubber, avoid twisting or excessive extension in up/down and right/
left directions.
• Tighten the bolts without causi ng interference with the flange.
Inspection After InstallationINFOID:0000000009460686
• With the engine running, check the exhaust tube joints for exhaust gas leaks and abnormal noise.
• Check that the mounting brackets and mounting insulators are installed properly and free from excessive stress. Improper installation could result in excessive noise, leaks, and vibration.
10. Rear muffler (LH) 11. Rear muffle r bracket (LH) 12. Rear muffler (RH)
13. Chrome exhaust finishers (if equipped)
Tool number : KV10114400 (J-38365)
Oxygen sensor thread cleaner : (J-43897-18)
Oxygen sensor thread cleaner : (J-43897-12)
Revision: November 20132014 Altima NAM

EXHAUST SYSTEM (VQ35DE)EX-11
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EX
NP
O
Removal and InstallationINFOID:0000000009460692
WARNING:
• Perform the procedure with the exhaust system fu lly cooled down because the system will be hot
just after the engine is turned off.
• Be careful not to cut your hand on the insulator edges.
CAUTION:
• Use Genuine NISSAN exhaust system parts or equival ent, which are specifically designed for heat
resistance, corrosion resistance, and shape.
REMOVAL
Remove exhaust system components using power tool.
• Remove heated oxygen sensor using Tool as needed.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Always replace exhaust gaskets with new ones when reassembling.
• Before installing a new heated o xygen sensor, clean and lube the exhaust tube threads using suit-
able tool.
• Discard any heated oxygen sensor which has been dr opped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; install a new one.
• Do not over-tighten the heated oxygen sensor. Doing so may damage the heated oxygen sensor,
resulting in the MIL coming on.
• If any mounting insulator is badly deformed, repair or replace it. If deposits such as mud pile up on
the mounting insulator, clean and inspect them.
• When installing the insulator avoid large gaps or interference between the insulator and each
exhaust pipe.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust gas leaks.
• Temporarily tighten the exhaust manifold side nut s and the vehicle side bolts. Check each part for
any interference, and then tighten th e nuts and bolts to specification.
• When installing each mounting ru bber, avoid twisting or excessive ext ension in up/down and right/
left directions.
• Tighten the bolts without causing interference with the flange.
Inspection After InstallationINFOID:0000000009460693
• With the engine running, check the exhaust tube joints for exhaust gas leaks and unusual noises.
• Check that the mounting brackets and mounting insula tors are installed properly and free from excessive
stress. Improper installation could result in excessive noise, leaks, and vibration.
Tool number : KV10114400 (J-38365)
Oxygen sensor thread cleaner : (J-43897-18)
Oxygen sensor thread cleaner : (J-43897-12)
Revision: November 20132014 Altima NAM

FRONT FOG LAMPEXL-125
< PERIODIC MAINTENANCE >
C
D E
F
G H
I
J
K
M A
B
EXL
N
O P
5. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the horizontal center line
of front fog lamp (H) and (A) becomes 100 mm (4 in).
A : Cutoff line
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp
X : Cutoff line height
JPLIA0008ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM