2014 NISSAN TEANA height

REAR DOORDLK-193
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
Unit: mm (in)
LONGITUDINAL CLEARANCE
1. Remove the center pillar upper finisher. Refer to INT-24, "CENTER PILLAR UPPER FINISHER : Removal
and Installation".
2. Loosen the rear door upper hinge nuts.
3. Loosen the rear door lower hinge bolts.
4. Move the rear door forward or backward as necessary until within specifications provided.
5. Tighten the lower hinge bolts to specification.
6. Tighten the upper hinge nuts to specification.
7. Install the center pillar upper finisher. Refer to INT-24, "CENTER PILLAR UPPER FINISHER : Removal
and Installation".
SURFACE HEIGHT ADJUSTMENT
1. Loosen the rear door hinge nuts (door side) (A).
2. Move the top and/or the bottom of the rear door (1) in or out as necessary until it is within specifications provided.
3. Tighten the rear door hinge nuts (door side) (A) to specification.
CAUTION:
• Check rear door hinge rotating poin t for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
• After adjusting, apply touch-up paint (body color) to the head of rear door hinge bolts and nuts.
Section Item Measurement Standard
A – A D Clearance 3.6
± 1.0 (0.14 ± 0.04)
E Surface height 0.0 ± 1.0 (0.00 ± 0.04)
B – B F Clearance 3.6
± 1.0 (0.14 ± 0.04)
G Surface height 0.0 ± 1.0 (0.0 ± 0.04)
C – C H Clearance 7.1 ± 1.7 (0.28 ± 0.07)
Rear door lower hinge
bolts 20.6 N·m (2.1 kg-m, 15 ft-lb)
Rear door upper hinge
nuts 20.6 N·m (2.1 kg-m, 15 ft-lb)
Rear door nuts 24.5 N·m (2.5 kg-m, 18 ft-lb)
ALKIA2710ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-208
< REMOVAL AND INSTALLATION >
TRUNK LID
TRUNK LID ASSEMBLY : Adjustment
INFOID:0000000009461955
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
1. Trunk lid assembly 2. Trunk lid hinge 3. Trunk lid striker
4. Body side outer 5. Rear combination lamp 6. Rear bumper fascia
A. Trunk bolts B. Striker bolts
ALKIA2735ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TRUNK LIDDLK-209
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
If the clearance and the surface height are out of specific ation, adjust them according to the adjustment proce-
dures.
Unit: mm (in)
LONGITUDINAL CLEARANCE
Trunk Lid Removed From Hinge
1. Loosen the trunk lid to hinge bolts.
2. Move the trunk lid so that the clearance m easurements are within specifications provided.
3. Tighten the trunk lid to hinge bolts.
Trunk Lid Hinge Removed From Vehicle
1. Remove the rear parcel shelf trim. Refer to INT-26, "Removal and Installation".
2. Loosen the hinge to parcel shelf bolts.
3. Move the trunk lid so that the clearance m easurements are within specifications provided.
4. Tighten the hinge to parcel shelf bolts.
5. Install the rear parcel shelf trim. Refer to INT-26, "Removal and Installation"
.
SURFACE HEIGHT ADJUSTMENT
1. Loosen the bumper rubber.
2. Loosen the striker bolts.
3. Lift up the trunk lid approx. 100 - 150 mm (3.94 - 5.91 in) height then close it lightly. Make sure it engages
firmly with the trunk lid closed.
4. Tighten the trunk lid striker.
TRUNK LID HINGE
TRUNK LID HINGE : Remo val and InstallationINFOID:0000000009461956
REMOVAL
1. Remove trunk lid assembly. Refer to DLK-206, "TRUNK LID ASSEMBLY : Removal and Installation".
2. Remove torsion bar. Refer to DLK-210, "TORSION BAR : Removal and Installation"
.
3. Remove rear parcel shelf finisher. Refer to INT-26, "Removal and Installation"
.
4. Release rear washer tube clips (RH only) (if equipped).
5. Remove trunk lid hinge bolts (body side) and then trunk lid hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check trunk lid open/close, lock/un lock operation after installation.
• After installation, perform the trunk li d assembly adjustment procedure. Refer to DLK-208, "TRUNK
LID ASSEMBLY : Adjustment".
Section Item Measurement Standard Parallelism (MAX) Right/Left
Difference (MAX)
A – A E Clearance 3.5
± 1.0 (0.14 ± 0.04) 1.4 (0.06) 1.4 (0.06)
F Surface height 0.0 ± 1.0 (0.00 ± 0.04) 1.4 (0.06) 1.4 (0.06)
B – B G Clearance 3.5
± 1.0 (0.14 ± 0.04) 1.4 (0.06) 1.4 (0.06)
H Surface height 0.0 ± 1.0 (0.00 ± 0.04) 1.4 (0.06) 1.4 (0.06)
C – C J Clearance 4.0 ± 1.5 (0.16 ± 0.06) — 2.0 (0.08)
D – D K Clearance 6.0 ± 2.0 (0.24 ± 0.08) 2.0 (0.08) —
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-214
< REMOVAL AND INSTALLATION >
FUEL FILLER LID OPENER
3. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler li d assembly open/close, lock/unlock operation.
NOTE:
• The following table shows the specifications for a correctly installed fuel filler lid.
• Fitting adjustment cannot be performed.
Unit: mm (in)
FUEL FILLER OP ENER CABLE
FUEL FILLER OPENER CABLE : Removal and InstallationINFOID:0000000009461963
REMOVAL
1. Remove hood and fuel filler handle assembly bolts (A).
2. Disengage fuel filler lid opener cable (2) by pulling downward and then sliding cable end to the side to remove from hood and
fuel filler handle assembly (1).
3. Remove dash side finisher (LH). Refer to INT-20, "DASH SIDE FINISHER : Removal and Installation"
.
4. Remove center pillar lower finisher (LH). Refer to INT-23, "CENTER PILLAR LOWER FINISHER :
Removal and Installation".
5. Remove rear seat bolster (LH). Refer to SE-38, "Removal and Installation - Rear Seat Bolster"
.
ALKIA2732ZZ
Portion Measurement Standard
Fuel filler lid – Body side outer Clearance 3.5 ± 1.0 (0.14 ± 0.04)
Fuel filler lid – Body side outer Surface height 0.0 ± 1.0 (0.0 ± 0.04)
JMKIA7998ZZ
JMKIA7999ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-216
< DTC/CIRCUIT DIAGNOSIS >[QR25DE]
P0031, P0032 A/F SENSOR 1 HEATER
3. Check the continuity between A/F sensor
1 harness connector and ECM harness connector.
*1: Except for California
*2: For California
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
3.CHECK A/F SENSOR 1 HEATER
Check the A/F sensor 1 heater. Refer to EC-216, "Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> GO TO 4.
4.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to EM-33, "Exploded View"
.
CAUTION:
• Discard any A/F sensor which has b een dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
• Before installing new A/F sensor, clean exhau st system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved Anti-seize Lubricant
(commercial service tool).
>> INSPECTION END
Component InspectionINFOID:0000000009462167
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1
1. Turn ignition switch OFF.
2. Disconnect A/F sensor 1 harness connector.
3. Check resistance between A/F sensor 1 terminals as per the following.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-33, "Exploded View"
.
CAUTION:
+ −
Continuity
A/F sensor 1 ECM
Connector Terminal Connector Terminal
F24 3 F13
*1
F90*253 Existed
A/F sensor 1
Resistance
+ −
Te r m i n a l
3 4 1.8 - 2.44
Ω [at 20 °C (68 °F)]
1
∞ Ω
(Continuity should not exist)
2
4 1
2
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-33
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
EXHAUST MANIFOLD AND THREE WAY CATALYST
Exploded ViewINFOID:0000000009460482
Removal and InstallationINFOID:0000000009460483
REMOVAL
1. Remove the engine under cover. Refer to
EXT-17, "Removal and Installation".
2. Remove the exhaust front tube. Refer to EX-5, "Exploded View"
.
3. Remove the front air duct and air cleaner assembly. Refer to EM-29, "Removal and Installation"
.
4. Disconnect the air fuel ratio (A/F) sensor 1 electrical harness connector.
5. Remove the exhaust manifold cover (upper).
6. Remove the air fuel ratio (A/F) sensor 1 (1) using Tools (A), (if necessary).
CAUTION:
• Be careful not to damage air fuel ratio (A/F) sensor.
• Discard any air fuel ratio (A/F) sensor which has been
dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; replace with a new
one.
7. Remove the oil level gauge and oil level gauge guide. Refer to EM-36, "Exploded View"
.
8. Remove the exhaust manifold cover (lower front).
1. Cylinder head 2. Exhaust manifold gasket 3. Exhaust manifold cover (upper)
4. Exhaust manifold and three way cat- alyst assembly 5. Exhaust manifold cover (lower
front) 6. Exhaust manifold cover (lower rear)
7. Air fuel ratio (A/F) sensor 1
AWBIA1314GB
Tool numbers : KV991J0050 (J-44626) : KV10117100 (J-36471-A)
ALBIA0919GB
Revision: November 20132014 Altima NAM

EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-35
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
4. Install the exhaust manifold cover (lower front) and bolts. Then
tighten the bolts to specification in the numerical order shown.
CAUTION:
Do not reuse bolts.
5. Install the air fuel ratio (A/F) sensor 1 (1) using Tools (A) and tighten to specification.
CAUTION:
• Be careful not to damage air fuel ratio (A/F) sensor.
• Discard any air fuel ratio (A/F) sensor which has been
dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; replace with a new
one.
• Do not over-tighten the air fuel ratio (A/F) sensor 1. Doing so may cause damage to the air fuel
ratio (A/F) sensor 1, r esulting in a malfunction and the MIL coming on.
6. Install the exhaust manifold cover (upper). Then tighten the bolts to specification in the numerical order shown.
CAUTION:
Do not reuse bolts.
7. Installation of the remaining components is in the reverse order of removal.
ALBIA0889GB
Tool numbers : KV991J0050 (J-44626) : KV10117100 (J-36471-A)
ALBIA0919GB
ALBIA0888GB
Revision: November 20132014 Altima NAM

EM-50
< REMOVAL AND INSTALLATION >[QR25DE]
CAMSHAFT
12. Loosen the camshaft bracket bolts in the order as shown, and
remove the camshaft brackets and camshafts.
NOTE:
Remove No.1 camshaft bracket by slightly tapping it with a rub-
ber mallet.
13. Remove the valve lifters. NOTE:
Check mounting positions, and set them aside in the order removed.
INSPECTION AFTER REMOVAL
Oil Filter
• Check that there is no foreign material on the oil filter (1) and check for clogging.
• Check the oil filter for damage.
• If there is damage, replace the oil filter.
Camshaft Runout
1. Put the camshaft on a V-block supporting the No.2 and No.5 journals.
CAUTION:
Do not support the No. 1 journal (on the side of the cam-
shaft sprocket) because it has different diameter from the
other four locations.
2. Set the dial gauge (A) vertically on the No.3 journal.
3. Turn camshaft in one direction by hand, and measure the cam- shaft runout on the dial gauge total indicator reading.
Camshaft Cam Height
1. Measure the camshaft cam height using suitable tool (A).
2. If wear is beyond the limit, replace the camshaft.
Camshaft Journal Clearance
Outer Diameter of Camshaft Journal
(A) : Intake side
(B) : Exhaust side
: Engine front
ALBIA0846GB
ALBIA0945ZZ
Standard : Less than 0.02 mm (0.0008 in)PBIC3177J
Standard intake cam height : 45.865 - 46.055 mm (1.8057 - 1.8132 in)
Standard exhaust cam height : 44.175 - 44.365 mm (1.7392 - 1.7467 in)
PBIC3178J
Revision: November 20132014 Altima NAM