2014 NISSAN TEANA check engine

IGNITION SIGNALEC-511
< DTC/CIRCUIT DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
IGNITION SIGNAL
Component Function CheckINFOID:0000000009462445
1.INSPECTION START
Turn ignition switch OFF, and restart engine.
Does the engine start?
YES-1 >> With CONSULT: GO TO 2.
YES-2 >> Without CONSULT: GO TO 3.
NO >> Proceed to EC-511, "Diagnosis Procedure"
.
2.CHECK IGNITION SIGNAL FUNCTION
With CONSULT
1. Perform “POWER BALANCE” in “ACTIVE TEST” mode with CONSULT.
2. Check that each circuit produces a momentary engine speed drop.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-511, "Diagnosis Procedure"
.
3.CHECK IGNITION SIGNAL FUNCTION
Without CONSULT
1. Let engine idle.
2. Read the voltage signal between ECM harness connector terminals with an oscilloscope.
*1: Except for California
*2: For California
NOTE:
The pulse cycle changes depending on rpm at idle.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-511, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009462446
1.CHECK ECM POWER SUPPLY
1. Turn ignition switch OFF, wait at least 10 seconds and then turn it ON.
2. Check the voltage between ECM harness connector terminals.
ECM
Voltage signal
+–
Connector Terminal Connector Terminal
F13
*1
F90*2
86 E10
*1
E31*2128
87
90
91
JMBIA0035GB
ECM Vo l ta g e
Connector +–
Te r m i n a l
E10
*1
E31*2121 128 Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-514
< DTC/CIRCUIT DIAGNOSIS >[QR25DE]
IGNITION SIGNAL
9.CHECK IGNITION COIL WITH POWER TRANSISTOR
Check ignition coil with power transistor. Refer to EC-514, "Component Inspection (Ignition Coil with Power
Transistor)".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace malfunctioning ignition coil with power transistor. Refer to EM-40, "Removal and Installa-
tion".
Component Inspection (Ignition Coil with Power Transistor)INFOID:0000000009462447
1.CHECK IGNITION COIL WITH POWER TRANSISTOR-1
1. Turn ignition switch OFF.
2. Disconnect ignition coil harness connector.
3. Check resistance between ignition coil terminals as per the following.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace malfunctioning ignition coil with power transistor. Refer to EM-40, "Removal and Installa-
tion".
2.CHECK IGNITION COIL WITH POWER TRANSISTOR-2
CAUTION:
Perform the following procedure in a place with no combustible objects and good ventilation.
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Remove fuel pump fuse in IPDM E/R to release fuel pressure.
NOTE:
Do not use CONSULT to release fuel pressure, or fuel pressure applies again during the following proce-
dure.
4. Start engine.
5. After engine stalls, crank it 2 or 3 times to release all fuel pressure.
6. Turn ignition switch OFF.
7. Remove all ignition coil harness connectors to avoi d the electrical discharge from the ignition coils.
8. Remove ignition coil and spark plug of the cylinder to be checked.
9. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.
10. Connect spark plug and harness connector to ignition coil.
11. Fix ignition coil using a rope etc. with gap of 13 - 17 mm (0.52 - 0.66 in) between the edge of the spark plug and grounded metal
portion as shown in the figure.
12. Crank engine for approximately 3 seconds, and check whether spark is generated between the spark plug and the grounded
metal portion.
CAUTION:
• During the operation, always stay 0.5 m (19.7 in) or more
away from the spark plug and the ignition coil. Be careful
not to get an electrical s hock while checking, because the
electrical discharge voltage becomes 20 kV or more.
• It might cause to damage the igni tion coil if the gap of more than 17 mm (0.66 in) is taken.
Ignition coil
Resistance Ω [at 25 °C (77 °F)]
+-
Terminal No. (Polarity)
1 2 Except 0 or
∞
3 Except 0
23
Spark should be generated.
JMBIA0066GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-516
< DTC/CIRCUIT DIAGNOSIS >[QR25DE]
INFORMATION DISPLAY (ASCD)
INFORMATION DISPLAY (ASCD)
Component Function CheckINFOID:0000000009462449
1.CHECK INFORMATION DISPLAY
1. Start engine.
2. Press ASCD MAIN switch on ASCD steering switch.
3. Drive the vehicle at more than 40 km/h (25 MPH). CAUTION:
Always drive vehicle at a safe speed.
4. Press SET/ − switch.
5. Check that the reading of the speedometer shows the same value as the set speed indicated in the infor-
mation display while driving the vehicle on a flat road.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-516, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009462450
1.CHECK DTC
Check that DTC UXXXX, P0500 or P1574 is not displayed.
Is the inspection result normal?
YES >> GO TO 2.
NO-1 >> Perform trouble diagnosis for DTC UXXXX.
NO-2 >> Perform trouble diagnosis for DTC P0500. Refer to EC-380, "DTC Logic"
.
NO-3 >> Perform trouble diagnosis for DTC P1574. Refer to EC-452, "DTC Logic"
.
2.CHECK DTC WITH COMBINATION METER
Refer to MWI-18, "CONSULT Function (METER/M&A)"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Perform trouble diagnosis for DTC indicated.
3.CHECK INTERMITTENT INCIDENT
Perform GI-43, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-82, "Removal and Installation".
NO >> Repair or replace error-detected parts.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

REFRIGERANT PRESSURE SENSOREC-523
< DTC/CIRCUIT DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
REFRIGERANT PRESSURE SENSOR
Component Function CheckINFOID:0000000009462456
1.CHECK REFRIGERANT PRE
SSURE SENSOR FUNCTION
1. Start engine and warm it up to normal operating temperature.
2. Turn A/C switch and blower fan switch ON.
3. Check the voltage between ECM harness connector terminals under the following conditions.
*1: Except for California
*2: For California
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-523, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009462457
1.CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY
1. Disconnect refrigerant pressu re sensor harness connector.
2. Turn ignition switch ON.
3. Check the voltage between refrigerant pr essure sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK REFRIGERANT PRESSURE SE NSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between refrigerant pre ssure sensor harness connector and ECM harness connec-
tor.
*1: Except for California
*2: For California
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO >> Repair or replace error-detected parts.
ECM
Voltage (V)
Connector +–
Te r m i n a l
E10
*1
E31*2103 124 1.0 - 4.0
+ -Vo l ta g e
(Approx.)
Refrigerant pressure sensor
Connector Terminal E219 1 Ground 5 V
+- Continuity
Refrigerant pressure sensor ECM
Connector Terminal Connector Terminal
E219 1 E10
*1
E31*2104 Existed
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-534
< PERIODIC MAINTENANCE >[QR25DE]
IDLE SPEED
PERIODIC MAINTENANCE
IDLE SPEED
InspectionINFOID:0000000009462463
1.CHECK IDLE SPEED
With CONSULT
Check idle speed in “DATA MONITOR” mode of “ENGINE” using CONSULT.
With GST
Check idle speed with Service $01 of GST.
>> INSPECTION END
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EVAP LEAK CHECKEC-537
< PERIODIC MAINTENANCE > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
EVAP LEAK CHECK
InspectionINFOID:0000000009462466
CAUTION:
• Do not use compressed air or a high pressure pump.
• Do not exceed 4.12 kPa (0.042 kg/cm
2, 0.6 psi) of pressure in EVAP system.
NOTE:
• Do not start engine.
• Improper installation of EVAP service port adapter [commercial service tool: (J-41413-OBD)] to the EVAP
service port may cause a leak.
1.EVAP LEAK CHECK
With CONSULT
1. Install EVAP service port adapter [commercial service tool: (J- 41413-OBD)] and pressure pump to EVAP service port.
2. Turn ignition switch ON.
3. Select the “EVAP SYSTEM CLOSE” in “WOR K SUPPORT” mode of “ENGINE” using CONSULT.
4. Touch “START”. A bar graph (Pressure indicating display) will appear on the screen.
5. Apply positive pressure to the EVAP system until t he pressure indicator reaches the middle of the bar
graph.
6. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
7. Locate the leak using a leak detector [commercial service tool: (J-41416)]. Refer to EC-62, "EVAPORATIVE EMISSION SYS-
TEM : System Description".
Without CONSULT
1. Install EVAP service port adapter [commercial service tool: (J- 41413-OBD)] and pressure pump to EVAP service port.
SEF462UA
SEF200U
SEF462UA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POSITIVE CRANKCASE VENTILATIONEC-539
< PERIODIC MAINTENANCE > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
POSITIVE CRANKCASE VENTILATION
InspectionINFOID:0000000009462467
1.CHECK PCV VALVE
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace PCV valve. Refer to EC-21,
"Component Parts Location".
PBIB1589E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PRECAUTIONSEC-543
< PRECAUTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
General PrecautionsINFOID:0000000009462477
•
Always use a 12 volt battery as power source.
• Never attempt to disconnect ba ttery cables while engine is
running.
• Before connecting or disc onnecting the ECM harness con-
nector, turn ignition switch OFF and disconnect negative bat-
tery cable. Failure to do so may damage the ECM because
battery voltage is applied to ECM even if ignition switch is
turned OFF.
• Before removing parts, turn ig nition switch OFF and then dis-
connect battery ground cable.
• Never disassemble ECM.
• If a battery cable is disconnected, the memory will return to the ECM value.
The ECM will now start to self-control at its initia l value. Thus, engine operation can vary slightly in
this case. However, this is not an indication of a malfunction. Never replace parts because of a slight
variation.
• If the battery is disconnected, the following emi ssion-related diagnostic information will be lost
within 24 hours.
- Diagnostic trouble codes
- 1st trip diagnostic trouble codes
- Freeze frame data
- 1st trip freeze frame data
- System readiness test (SRT) codes
- Test values
• When connecting ECM harness connector, fasten (B) it
securely with a lever (1) as far as it will go as shown in the fig-
ure.
- ECM (2)
- Loosen (A)
• When connecting or disconnect ing pin connectors into or
from ECM, never damage pin terminals (bends or break).
Check that there are not any bends or breaks on ECM pin ter-
minal, when connect ing pin connectors.
• Securely connect ECM harness connectors.
A poor connection can cause an extremely high (surge) volt-
age to develop in coil and cond enser, thus resulting in dam-
age to ICs.
• Keep engine control system harness at least 10 cm (4 in) away
from adjacent harness, to prevent engine control system mal-
functions due to receiving externa l noise, degraded operation
of ICs, etc.
• Keep engine control system parts and harness dry.
SEF289H
PBIB2947E
PBIB0090E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM