2014 NISSAN TEANA sensor

EC-13
C
D E
F
G H
I
J
K L
M
EC A
N
O P
P1574 ASCD VEHICLE SPEED SENSOR .... ..918
Description .......................................................... ..918
DTC Logic .............................................................918
Diagnosis Procedure .............................................918
P1800 VIAS CONTROL SOLENOID VALVE 1 ..920
DTC Logic ........................................................... ..920
Diagnosis Procedure .............................................920
Component Inspection ..........................................921
P1801 VIAS CONTROL SOLENOID VALVE 2 ..922
DTC Logic ........................................................... ..922
Diagnosis Procedure .............................................922
Component Inspection ..........................................923
P1805 BRAKE SWITCH ................................. ..924
Description .......................................................... ..924
DTC Logic .............................................................924
Diagnosis Procedure .............................................924
Component Inspection (Stop Lamp Switch) ..........926
Component Inspection (Stop Lamp Relay) ...........926
P2096, P2097, P2098, P2099 A/F SENSOR 1 ..927
DTC Logic ........................................................... ..927
Diagnosis Procedure .............................................927
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY ................................................... ..
931
DTC Logic ........................................................... ..931
Diagnosis Procedure .............................................931
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ..................................................... ..
933
DTC Logic ........................................................... ..933
Diagnosis Procedure .............................................933
Component Inspection ..........................................935
P2118 THROTTLE CONTROL MOTOR ..........936
DTC Logic ........................................................... ..936
Diagnosis Procedure .............................................936
Component Inspection ..........................................937
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR .................................................... ..
938
DTC Logic ........................................................... ..938
Diagnosis Procedure .............................................938
P2122, P2123 APP SENSOR ...........................940
DTC Logic ........................................................... ..940
Diagnosis Procedure .............................................940
Component Inspection ..........................................941
P2127, P2128 APP SENSOR ...........................942
DTC Logic ........................................................... ..942
Diagnosis Procedure .............................................942
Component Inspection ..........................................943
P2135 TP SENSOR ..........................................945
DTC Logic ........................................................... ..945
Diagnosis Procedure .............................................945
Component Inspection ..........................................946
P2138 APP SENSOR ......................................947
DTC Logic ............................................................ ..947
Diagnosis Procedure .............................................947
Component Inspection ...........................................949
BRAKE PEDAL POSITION SWITCH .............950
Component Function Check ..................................950
Diagnosis Procedure .............................................950
Component Inspection (Brake Pedal Position
Switch) ................................................................. ..
951
ASCD INDICATOR ..........................................952
Component Function Check ..................................952
Diagnosis Procedure .............................................952
COOLING FAN ................................................953
Component Function Check ..................................953
Diagnosis Procedure .............................................953
Component Inspection (Cooling Fan Motor) ..........955
Component Inspection (Cooling Fan Relay) ..........956
ELECTRICAL LOAD SIGNAL ........................957
Description .............................................................957
Component Function Check ..................................957
Diagnosis Procedure .............................................957
ELECTRONIC CONTROLLED ENGINE
MOUNT ............................................................
959
Component Function Check ................................ ..959
Diagnosis Procedure .............................................959
Component Inspection ...........................................960
FUEL INJECTOR ............................................962
Component Function Check ..................................962
Diagnosis Procedure .............................................962
Component Inspection ...........................................963
FUEL PUMP ....................................................965
Component Function Check ..................................965
Diagnosis Procedure .............................................965
Component Inspection ...........................................966
IGNITION SIGNAL ..........................................967
Component Function Check ..................................967
Diagnosis Procedure .............................................967
Component Inspection (Ignition Coil with Power
Transistor) ........................................................... ..
970
Component Inspection (Condenser) ......................971
INFORMATION DISPLAY (ASCD) .................972
Component Function Check ..................................972
Diagnosis Procedure .............................................972
MALFUNCTION INDICATOR LAMP ..............973
Component Function Check ..................................973
Diagnosis Procedure .............................................973
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) ....................................................
974
Component Function Check ................................ ..974
Diagnosis Procedure .............................................974
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-14
Component Inspection ...........................................976
REFRIGERANT PRESSURE SENSOR ..........979
Component Function Check ................................ ..979
Diagnosis Procedure .............................................979
SENSOR POWER SUPPLY2 CIRCUIT ...........981
Description ........................................................... ..981
Diagnosis Procedure .............................................981
VARIABLE INDUCTION AIR SYSTEM ...........983
Component Function Check ................................ ..983
Diagnosis Procedure .............................................984
SYMPTOM DIAGNOSIS ............................987
ENGINE CONTROL SYSTEM SYMPTOMS .. .987
Symptom Table ................................................... ..987
NORMAL OPERATING CONDITION ..............991
Description ........................................................... ..991
PERIODIC MAINTENANCE ..................... ..992
IDLE SPEED ................................................... .992
Work Procedure ................................................... ..992
IGNITION TIMING .............................................993
Work Procedure ................................................... .993
EVAP LEAK CHECK ........................................994
Work Procedure ................................................... .994
POSITIVE CRANKCASE VENTILATION .........996
Work Procedure ................................................... .996
REMOVAL AND INSTALLATION .............997
ECM ................................................................ ..997
Removal and Installation .......................................997
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... ..........................................
998
SERVICE DATA AND SPECIFICATIONS
(SDS) .............................................................. ..
998
Idle Speed ............................................................ .998
Ignition Timing .......................................................998
Calculated Load Value ..........................................998
Mass Air Flow Sensor ...........................................998
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PRECAUTIONSEC-15
< PRECAUTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental
Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951805
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service t he system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Precaution for Procedure without Cowl Top CoverINFOID:0000000009462048
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
On Board Diagnostic (OBD) S ystem of Engine and CVTINFOID:0000000009462049
The ECM has an on board diagnostic system . It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:
• Be sure to turn the ignition switch OFF and di sconnect the negative battery cable before any repair
or inspection work. The open/short circuit of re lated switches, sensors, solenoid valves, etc. will
cause the MIL to light up.
• Be sure to connect and lock the connectors secure ly after work. A loose (unlocked) connector will
cause the MIL to light up due to the open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
• Certain systems and components, especially those related to OBD, may use a new style slide-lock-
ing type harness connector. For descripti on and how to disconnect, refer to PG-65, "Description"
.
• Be sure to route and secure the harnesses properly after work. The interference of the harness with
a bracket, etc. may cause the MIL to li ght up due to the short circuit.
PIIB3706J
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-16
< PRECAUTION >[QR25DE]
PRECAUTIONS
• Be sure to connect rubber tubes properly afte
r work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to the malfunction of the EVAP system or fuel injection system,
etc.
• Be sure to erase the unnecessary malfunction info rmation (repairs completed) from the ECM and
TCM (Transmission control module) before returning the vehicle to the customer.
General PrecautionsINFOID:0000000009462050
•Always use a 12 volt battery as power source.
• Do not attempt to disconnect battery cables while engine is
running.
• Before connecting or disconnecting the ECM harness con-
nector, turn ignition switch OFF and disconnect negative bat-
tery cable. Failure to do so may damage the ECM because
battery voltage is applied to ECM even if ignition switch is
turned OFF.
• Before removing parts, turn ig nition switch OFF and then dis-
connect battery ground cable.
• Do not disassemble ECM.
• If a battery cable is disconnected, the memory will return to
the ECM value.
The ECM will now start to self-control at its initial value.
Engine operation can vary slight ly when the terminal is dis-
connected. However, this is no t an indication of a malfunc-
tion. Do not replace parts b ecause of a slight variation.
• If the battery is disconnected, the following emission-related
diagnostic information will be lost within 24 hours.
- Diagnostic trouble codes
- 1st trip diagnostic trouble codes
- Freeze frame data
- 1st trip freeze frame data
- System readiness test (SRT) codes
- Test values
• When connecting or disconnect ing pin connectors into or
from ECM, take care not to damage pin terminals (bend or
break).
Make sure that there are not any bends or breaks on ECM pin
terminal, when connecting pin connectors.
• Securely connect ECM harness connectors.
A poor connection can cause an extremely high (surge) volt-
age to develop in coil and co ndenser, thus resulting in dam-
age to ICs.
• Keep engine control system harness at least 10 cm (4 in) away
from adjacent harness, to preven t engine control system mal-
functions due to receiving exter nal noise, degraded operation
of ICs, etc.
• Keep engine control system parts and harness dry.
• Before replacing ECM, perform ECM Terminals and Reference
Value inspection and make sure ECM functions properly.
Refer to EC-88, "Reference Value"
.
• Handle mass air flow sensor carefully to avoid damage.
• Do not clean mass air flow senso r with any type of detergent.
• Do not disassemble electric throttle control actuator.
• Even a slight leak in the ai r intake system can cause serious
incidents.
• Do not shock or jar the camshaft position sensor (PHASE),
crankshaft position sensor (POS).
SEF289H
PBIA9222J
PBIB0090E
MEF040D
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-20
< PREPARATION >[QR25DE]
PREPARATION
Socket wrench Removes and installs engine coolant temperature
sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12) Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907) Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Tool name
(TechMate No.) Description
S-NT705
AEM488
S-NT779
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-21
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000009462053
ENGINE ROOM COMPARTMENT
ALBIA0804ZZ
No. Component Function
EVAP canister purge volume control solenoid valve EC-34, "EVAP Canister Purge Volume Control Solenoid
Va l v e "
Transmission range switch• The transmission range switch is installed to upper part
of transaxle case.
• ECM detects the selector lever position because the continuity of the transmission range switch line (the
ON) exists.
ECM EC-25, "ECM"
Refrigerant pressure sensorEC-36, "Refrigerant Pressure Sensor"
Battery current sensor
(with battery temperature sensor) EC-35, "Battery Current Se
nsor (With Battery Tempera-
ture Sensor)"
IPDM E/R • IPDM E/R control the internal relays and the actuators.
-Refer to PCS-6, "RELAY CONTROL SYSTEM : Sys-tem Description".
• When CAN communication with ECM is impossible,
IPDM E/R performs fail-safe control.
-Refer to PCS-19, "Fail Safe"
.
Mass air flow sensor
(with intake air temperature sensor) EC-27, "Mass Air Flow Sensor (With Intake Air Tempera-
ture Sensor)"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-22
< SYSTEM DESCRIPTION >[QR25DE]
COMPONENT PARTS
ENGINE COMPARTMENT
Intake manifold runner control valve actuator
EC-31, "Intake Manifold Runner Control Valve"
Electric throttle control actuator
(with built in throttle position sensor and throttle control motor) EC-25, "Electric Thrott
le Control Actuator"
EVAP service port When perform the EVAP leak check, positive pressure is
delivered to the EVAP system through the EVAP service
port.
Refer to EC-537, "Inspection"
.
No. Component Function
JPBIA5840ZZ
Engine rear side Intake side
: Vehicle front
No. Component Function
Exhaust valve timing control position sensor EC-30, "Exhaust Valve Timing Control Position Sensor"
Camshaft position sensor (PHASE)EC-29, "Camshaft Position Sensor (PHASE)"
PCV valveThe positive crankcase ventilation (PCV) valve is provided
to conduct crankcase blow-by gas to the intake manifold.
Fuel injector EC-26, "Fuel Injector"
Crankshaft position sensor (POS)EC-29, "Crankshaft Position Sensor (POS)"
Knock sensorEC-33, "Knock Sensor"
Engine oil temperature sensorEC-33, "Engine Oil Temperature Sensor"
Engine oil pressure sensorEC-33, "Engine Oil Pressure Sensor"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-23
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
EXHAUST COMPARTMENT
BODY COMPARTMENT
Intake valve timing intermediate lock control solenoid valve
EC-30, "Intake Valve Timing Intermediate Lock Control So-lenoid Valve"
Intake valve timing control solenoid valve
EC-30, "Intake Valve Timing Control Solenoid Valve"
Exhaust valve timing control solenoid valveEC-31, "Exhaust Valve Timing Control Solenoid Valve"
Ignition coil (with power transistor)EC-26, "Ignition Coil With Power Transistor"
Engine coolant temperature sensorEC-28, "Engine Coolant Temperature Sensor"
Intake manifold tuning valveEC-31, "Intake Manifold Tuning Valve"
Intake manifold runner control valve position sensor
EC-31, "Intake Manifold Runner Control Valve"
Intake manifold runner control valve actuator
No. Component Function
To engine assembly
JPBIA5841ZZ
No. Component Function
Air fuel ratio (A/F) sensor 1 EC-32, "Air Fuel Ratio (A/F) Sensor 1"
Heated oxygen sensor 2EC-32, "Heated Oxygen Sensor 2"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM