2014 NISSAN TEANA oil temperature

WATER OUTLET AND WATER PIPINGCO-51
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
WATER OUTLET AND WATER PIPING
Exploded ViewINFOID:0000000009460424
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly push down and
turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down
and turning it all the way.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
Removal and InstallationINFOID:0000000009460425
REMOVAL
1. Remove engine room cover. Refer to EM-28, "Removal and Installation".
CAUTION:
Perform when the engine is cold.
1. Heater hose 2. Clamp 3. Water hose
4. Clamp 5. Water outlet 6. Gasket
7. Gasket 8. Water connector 9. O-ring
10. Water bypass pipe 11. Clamp 12. Water hose
13. Heater pipe 14. Water hose 15. Heater hose
16. Engine coolant temperature sensor 17. Clamp 18. Radiator hose (upper)
A. To heater core B. To electric throttle control actuator C. To oil cooler
D. To radiator
AWBIA1107GB
Revision: November 20132014 Altima NAM

DAS-38
< BASIC INSPECTION >[ITS CONTROL UNIT]
REAR VIEW CAMERA CALIBRATION
REAR VIEW CAMERA CALIBRATION
DescriptionINFOID:0000000009464665
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
• Place the vehicle on level ground wh en the calibration is performed.
• Follow the CONSULT when performing the calib ration. (Rear view camera calibration cannot be
operated without CONSULT).
Work Procedure (Preparation)INFOID:0000000009464666
1.PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of the ITS control unit.
Is any DTC detected?
Except "U1308">> Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
DAS-20, "DTC Index"
.
"U1308" or no DTC>> GO TO 2.
2.PREPARATION BEFORE REAR VIEW CAMERA CALIBRATION
NOTE:
Select the "AVM" to diagnose the ITS control unit by CONSULT.
1. Perform pre-inspection for diagnosis. Refer to DAS-34, "Inspection Procedure"
.
2. Adjust the tire pressure to the specified pressure value.
3. Maintain no-load in vehicle.
4. Check if coolant and engine oil are filled up to correct level and fuel tank is full.
5. Situate vehicle where the camera is ex posed at an atmosphere temperature between 0 °C (32 °F) and
30 °C (86 °F)
6. Move the shift selector to P (Park) and release the parking brake.
7. Clean the rear view camera.
>> GO TO 3.
3.PREPARATION OF CALIBRATION TARGET MARK
Prepare the calibration target mark according to the following figure:
ALOIA0186ZZ
(1) : Left and right targets
(2) : Center target
(A) : Side of the black or white area = 200 mm (7.87 in)
(B) : Side of the square target = 400 mm (15.75 in)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
REAR VIEW CAMERA CALIBRATIONDAS-107
< BASIC INSPECTION > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
REAR VIEW CAMERA CALIBRATION
DescriptionINFOID:0000000009464741
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
• Place the vehicle on level ground when the calibration is performed.
• Follow the CONSULT when performing the calib ration. (Rear view camera calibration cannot be
operated without CONSULT).
Work Procedure (Preparation)INFOID:0000000009464742
1.PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of the ITS control unit.
Is any DTC detected?
Except "U1308">> Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
DAS-89, "DTC Index"
.
"U1308" or no DTC>>GO TO 2.
2.PREPARATION BEFORE REAR VIEW CAMERA CALIBRATION
NOTE:
Select the "AVM" to diagnose the ITS control unit by CONSULT.
1. Perform pre-inspection for diagnosis. Refer to DAS-103, "Inspection Procedure"
.
2. Adjust the tire pressure to the specified pressure value.
3. Maintain no-load in vehicle.
4. Check if coolant and engine oil are filled up to correct level and fuel tank is full.
5. Situate vehicle where the camera is ex posed at an atmosphere temperature between 0 °C (32 °F) and
30 °C (86 °F)
6. Move the shift selector to P (Park) and release the parking brake.
7. Clean the rear view camera.
>> GO TO 3.
3.PREPARATION OF CALIBRATION TARGET MARK
Prepare the calibration target mark according to the following figure:
ALOIA0186ZZ
(1) : Left and right targets
(2) : Center target
(A) : Side of the black or white area = 200 mm (7.87 in)
(B) : Side of the square target = 400 mm (15.75 in)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-182
< BASIC INSPECTION >[BSW]
REAR VIEW CAMERA CALIBRATION
REAR VIEW CAMERA CALIBRATION
DescriptionINFOID:0000000009464825
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
• Place the vehicle on level ground wh en the calibration is performed.
• Follow the CONSULT when performing the calib ration. (Rear view camera calibration cannot be
operated without CONSULT).
Work Procedure (Preparation)INFOID:0000000009464826
1.PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of the ITS control unit.
Is any DTC detected?
Except "U1308">> Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
DAS-164, "DTC Index"
.
"U1308" or no DTC>>GO TO 2.
2.PREPARATION BEFORE REAR VIEW CAMERA CALIBRATION
NOTE:
Select the "AVM" to diagnose the ITS control unit by CONSULT.
1. Perform pre-inspection for diagnosis. Refer to DAS-158, "CONSULT Function (AVM)"
.
2. Adjust the tire pressure to the specified pressure value.
3. Maintain no-load in vehicle.
4. Check if coolant and engine oil are filled up to correct level and fuel tank is full.
5. Situate vehicle where the camera is ex posed at an atmosphere temperature between 0 °C (32 °F) and
30 °C (86 °F)
6. Move the shift selector to P (Park) and release the parking brake.
7. Clean the rear view camera.
>> GO TO 3.
3.PREPARATION OF CALIBRATION TARGET MARK
Prepare the calibration target mark according to the following figure:
ALOIA0186ZZ
(1) : Left and right targets
(2) : Center target
(A) : Side of the black or white area = 200 mm (7.87 in)
(B) : Side of the square target = 400 mm (15.75 in)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-256
< BASIC INSPECTION >[MOD]
REAR VIEW CAMERA CALIBRATION
REAR VIEW CAMERA CALIBRATION
DescriptionINFOID:0000000009464906
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
• Place the vehicle on level ground wh en the calibration is performed.
• Follow the CONSULT when performing the calib ration. (Rear view camera calibration cannot be
operated without CONSULT).
Work Procedure (Preparation)INFOID:0000000009464907
1.PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of the ITS control unit.
Is any DTC detected?
Except "U1308">> Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
DAS-239, "DTC Index"
.
"U1308" or no DTC>>GO TO 2.
2.PREPARATION BEFORE REAR VIEW CAMERA CALIBRATION
NOTE:
Select the "AVM" to diagnose the ITS control unit by CONSULT.
1. Perform pre-inspection for diagnosis. Refer to DAS-253, "Inspection Procedure"
.
2. Adjust the tire pressure to the specified pressure value.
3. Maintain no-load in vehicle.
4. Check if coolant and engine oil are filled up to correct level and fuel tank is full.
5. Situate vehicle where the camera is ex posed at an atmosphere temperature between 0 °C (32 °F) and
30 °C (86 °F)
6. Move the shift selector to P (Park) and release the parking brake.
7. Clean the rear view camera.
>> GO TO 3.
3.PREPARATION OF CALIBRATION TARGET MARK
Prepare the calibration target mark according to the following figure:
ALOIA0186ZZ
(1) : Left and right targets
(2) : Center target
(A) : Side of the black or white area = 200 mm (7.87 in)
(B) : Side of the square target = 400 mm (15.75 in)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-1
ENGINE
C
D E
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
QR25DE
PRECAUTION ................ ..............................
15
PRECAUTIONS .............................................. ....15
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
15
Precaution for Procedure without Cowl Top Cover ....15
On Board Diagnostic (OBD) System of Engine
and CVT .............................................................. ....
15
General Precautions ...............................................16
PREPARATION ...........................................19
PREPARATION .............................................. ....19
Special Service Tools .......................................... ....19
Commercial Service Tools ......................................19
SYSTEM DESCRIPTION .............................21
COMPONENT PARTS ................................... ....21
Component Parts Location ................................ ....21
ECM ........................................................................25
Accelerator Pedal Position Sensor ...................... ....25
Electric Throttle Control Actuator ........................ ....25
Ignition Coil With Power Transistor .........................26
Fuel Injector ........................................................ ....26
Fuel Level Sensor Unit and Fuel Pump .............. ....26
Fuel Tank Temperature Sensor .......................... ....27
Mass Air Flow Sensor (With Intake Air Tempera-
ture Sensor) ........................................................ ....
27
Manifold Absolute Pressure Sensor ........................28
Engine Coolant Temperature Sensor .................. ....28
Crankshaft Position Sensor (POS) ..........................29
Camshaft Position Sens or (PHASE) .......................29
Intake Valve Timing Cont rol Solenoid Valve ...........30
Intake Valve Timing Intermediate Lock Control
Solenoid Valve .................................................... ....
30
Exhaust Valve Timing Control Position Sensor .......30
Exhaust Valve Timing Control Solenoid Valve ........31
Intake Manifold Runner Control Valve ................. ....31
Intake Manifold Tuning Valve ..................................31
Air Fuel Ratio (A/F) Sensor 1 ..................................32
Heated Oxygen Sensor 2 ........................................32
Knock Sensor ..........................................................33
Engine Oil Pressure Sensor ....................................33
Engine Oil Temperature Sensor .......................... ....33
Cooling Fan .............................................................34
EVAP Canister .........................................................34
EVAP Canister Purge Volu me Control Solenoid
Valve .................................................................... ....
34
EVAP Canister Vent Control Valve ..........................35
EVAP Control System Pres sure Sensor ..................35
Battery Current Sensor (With Battery Tempera-
ture Sensor) ......................................................... ....
35
Malfunction Indicator lamp (MIL) .............................36
Oil Pressure Warning Lamp ....................................36
Refrigerant Pressure Sensor ............................... ....36
Stop Lamp Switch & Brake Pedal Position Switch ....36
ASCD Steering Switch .............................................37
Information Display ..................................................37
STRUCTURE AND OPERATION .....................38
Positive Crankcase Ventilation ................................38
On Board Refueling Vapor Recovery (ORVR) ........39
SYSTEM ............................................................40
ENGINE CONTROL SYSTEM ........................ ...........40
ENGINE CONTROL SYSTEM : System Descrip-
tion ....................................................................... ....
40
ENGINE CONTROL SYSTEM : Fail Safe ..............41
MULTIPORT FUEL INJECTION SYSTEM ................43
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description (with auto matic air conditioner) ......
43
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description (with manual air conditioner) .........
46
ELECTRIC IGNITION SYSTEM .................................48
ELECTRIC IGNITION SYSTEM : System De-
scription ............................................................... ....
48
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-8
POSITIVE CRANKCASE VENTILATION ........539
Inspection ............................................................ ..539
REMOVAL AND INSTALLATION ..............540
ECM ................................................................ .540
Removal and Installation ..................................... ..540
SERVICE DATA AND SPECIFICATIONS
(SDS) .............. ............................................
541
SERVICE DATA AND SPECIFICATIONS
(SDS) ............................................................... .
541
Idle Speed ........................................................... ..541
Ignition Timing .......................................................541
Calculated Load Value ..........................................541
Mass Air Flow Sensor ............................................541
VQ35DE
PRECAUTION .............. ..............................
542
PRECAUTIONS .............................................. .542
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. ..
542
On Board Diagnostic (OBD) System of Engine
and CVT .............................................................. ..
542
General Precautions ..............................................543
PREPARATION ..........................................546
PREPARATION .............................................. .546
Special Service Tools .......................................... ..546
Commercial Service Tools .....................................546
SYSTEM DESCRIPTION ...........................548
COMPONENT PARTS .................................... .548
ENGINE CONTROL SYSTEM .................................548
ENGINE CONTROL SYSTEM : Component Parts
Location ............................................................... ..
548
Accelerator Pedal Position Sensor ........................552
Air Fuel Ratio (A/F) Sensor 1 ................................552
ASCD Steering Switch ...........................................553
Battery Current Sensor (With Battery Tempera-
ture Sensor) ......................................................... ..
553
Camshaft Position Sensor (PHASE) .....................554
Cooling Fan ......................................................... ..554
Crankshaft Position Sensor (POS) ........................554
ECM .......................................................................555
Electric Throttle Control Actuator ......................... ..555
Electronic Controlled Engine Mount .................... ..556
Engine Coolant Temperature Sensor ....................556
Engine Oil Pressure Sensor ................................ ..557
Engine Oil Temperature Sensor ............................557
EVAP Canister ..................................... ..................557
EVAP Canister Purge Volu me Control Solenoid
Valve .................................................................... ..
557
EVAP Canister Vent Control Valve ........................558
EVAP Control System Pressu re Sensor ................558
Fuel Injector ......................................................... .558
Fuel Level Sensor Unit and Fuel Pump (With Fuel
Tank Temperature Sensor) .................................. .
558
Heated Oxygen Sensor 2 ......................................559
Ignition Coil (With Power Transistor) ....................560
Intake Valve Timing Control Solenoid Valve .........560
Knock Sensor ....................................................... .560
Malfunction Indicator lamp (MIL) ...........................560
Mass Air Flow Sensor (With Intake Air Tempera-
ture Sensor) ......................................................... .
560
Oil Pressure Warning Lamp ..................................561
Power Valve Actuator 1 and 2 ..............................561
Refrigerant Pressure Sensor ................................562
Stop Lamp Switch & Brak e Pedal Position Switch .562
VIAS Control Solenoid Valve 1 and 2 .................. .562
STRUCTURE AND OPERATION .....................563
Positive Crankcase Ventilation (PCV) ...................563
On Board Refueling Vapor Recovery (ORVR) ..... .564
SYSTEM ...........................................................565
ENGINE CONTROL SYSTEM ................................ .565
ENGINE CONTROL SYSTEM : System Descrip-
tion ....................................................................... .
565
ENGINE CONTROL SYSTEM : Fail-safe .............566
MULTIPORT FUEL INJECTION SYSTEM ............. .568
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description .................................................... .
568
ELECTRIC IGNITION SYSTEM ............................. .571
ELECTRIC IGNITION SYSTEM : System De-
scription ................................................................ .
571
AIR CONDITIONING CUT CONTROL ................... .572
AIR CONDITIONING CUT CONTROL : System
Description ........................................................... .
573
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .574
AUTOMATIC SPEED CONTROL DEVICE (AS-
CD) : System Description ..................................... .
574
COOLING FAN CONTROL .................................... .575
COOLING FAN CONTROL : System Description .575
ELECTRONIC CONTROLLED ENGINE MOUNT .. .577
ELECTRONIC CONTROLLED ENGINE MOUNT
: System Description ............................................ .
577
EVAPORATIVE EMISSION SYSTEM .....................579
EVAPORATIVE EMISSION SYSTEM : System
Description ........................................................... .
580
THROTTLE CONTROL ...........................................581
THROTTLE CONTROL : Syst em Description ......581
INTAKE VALVE TIMING CONTROL ..................... .582
INTAKE VALVE TIMING CONTROL : System De-
scription ................................................................ .
583
ENGINE PROTECTION CONTROL AT LOW EN-
GINE OIL PRESSURE ........................................... .
583
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-12
Diagnosis Procedure .............................................865
P0462, P0463 FUEL LEVEL SENSOR ...........866
DTC Logic ............................................................ ..866
Diagnosis Procedure .............................................866
P0500 VSS .......................................................867
Description ........................................................... ..867
DTC Logic ..............................................................867
Diagnosis Procedure .............................................867
P0506 ISC SYSTEM ........................................869
Description ........................................................... ..869
DTC Logic ..............................................................869
Diagnosis Procedure .............................................869
P0507 ISC SYSTEM ........................................871
Description ........................................................... ..871
DTC Logic ..............................................................871
Diagnosis Procedure .............................................871
P050A, P050E COLD START CONTROL .......873
Description ........................................................... ..873
DTC Logic ..............................................................873
Diagnosis Procedure .............................................874
P0520 EOP SENSOR ......................................875
DTC Logic ............................................................ ..875
Diagnosis Procedure .............................................875
Component Inspection ...........................................877
P0524 ENGINE OIL PRESSURE ....................878
DTC Logic ............................................................ ..878
Diagnosis Procedure .............................................879
Component Inspection ...........................................880
P0603 ECM POWER SUPPLY ........................881
DTC Logic ............................................................ ..881
Diagnosis Procedure .............................................881
P0605 ECM ......................................................883
DTC Logic ............................................................ ..883
Diagnosis Procedure .............................................883
P0607 ECM ......................................................884
DTC Logic ............................................................ ..884
Diagnosis Procedure .............................................884
P0643 SENSOR POWER SUPPLY .................885
Description ........................................................... ..885
DTC Logic ..............................................................885
Diagnosis Procedure .............................................885
P0850 PNP SWITCH .......................................887
Description ........................................................... ..887
DTC Logic ..............................................................887
Component Function Check ..................................888
Diagnosis Procedure .............................................888
P1148, P1168 CLOSED LOOP CONTROL .....890
DTC Logic ............................................................ ..890
P1212 TCS COMMUNICATION LINE ..............891
Description ........................................................... .891
DTC Logic .............................................................891
Diagnosis Procedure .............................................891
P1217 ENGINE OVER TEMPERATURE .........892
DTC Logic ............................................................ .892
Component Function Check .................................892
Diagnosis Procedure .............................................893
P1225 TP SENSOR ..........................................895
DTC Logic ............................................................ .895
Diagnosis Procedure .............................................895
P1226 TP SENSOR ..........................................896
DTC Logic ............................................................ .896
Diagnosis Procedure .............................................896
P1550 BATTERY CURRENT SENSOR ...........897
DTC Logic ............................................................ .897
Diagnosis Procedure .............................................897
Component Inspection ..........................................898
P1551, P1552 BATTERY CURRENT SEN-
SOR ................................................................ ..
899
DTC Logic ............................................................ .899
Diagnosis Procedure .............................................899
Component Inspection ..........................................900
P1553 BATTERY CURRENT SENSOR ...........901
DTC Logic ............................................................ .901
Diagnosis Procedure .............................................901
Component Inspection ..........................................902
P1554 BATTERY CURRENT SENSOR ...........903
DTC Logic ............................................................ .903
Component Function Check .................................903
Diagnosis Procedure .............................................903
Component Inspection ..........................................904
P1556, P1557 BATTERY TEMPERATURE
SENSOR ......................................................... ..
906
DTC Logic ............................................................ .906
Diagnosis Procedure .............................................906
Component Inspection (Battery Temperature
Sensor) ................................................................ .
907
P1564 ASCD STEERING SWITCH ..................908
DTC Logic ............................................................ .908
Diagnosis Procedure .............................................908
Component Inspection ..........................................910
P1572 ASCD BRAKE SWITCH ........................911
Description ........................................................... .911
DTC Logic .............................................................911
Component Function Check .................................912
Diagnosis Procedure .............................................913
Component Inspection (Brake Pedal Position
Switch) ................................................................. .
916
Component Inspection (Stop Lamp Switch) ..........916
Component Inspection (Stop Lamp Relay) ...........917
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM