2014 NISSAN TEANA recommended oil

ENGINE COOLANTCO-37
< PERIODIC MAINTENANCE > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
• Do not allow the coolant to
contact the drive belts.
• Perform this step when engine is cold.
5. When draining all of the coolant in the system for engine removal or repair, open all of the drain plugs (A-D) on the cylin-
der block.
6. Check the drained coolant for contaminants such as rust, corro- sion or discoloration.
If the coolant is contaminated, flush the engine cooling system.
REFILLING ENGINE COOLANT
1. Install the radiator drain plug. If the cooling syst em was drained completely, install the reservoir tank and
the cylinder block drain plugs.
• The radiator must be complete ly empty of coolant and water.
• Apply sealant to the threads of the cylinder block drain plug. Use Genuine High Performance
Thread Sealant or equivalent. Refer to GI-21, "Recommended Chemical Products and Sealants"
.
CAUTION:
Do not reuse copper sealing washers.
2. If disconnected, reattach the upper radiator hose at the engine side.
3. Set the vehicle heater controls to the full HOT and heat er ON position. Turn the vehicle ignition ON with
the engine OFF as necessary to activate the heater mode.
PBIC2487E
Radiator drain plug : Refer to CO-16, "Exploded View"
Cylinder block front drain plug (LH) (A) (ex-
cept Canada) : 62.0 N·m (6.3 kg-m, 46 ft-lb)
Cylinder block water drain plug (B) : 6.0 N·m (0.6 kg-m, 53 in-lb)
Cylinder block rear drain plug (C) : 78.0 N·m (8.0 kg-m, 58 ft-lb)
Cylinder block RH banjo bolt (D) (oil co oler) : 19.6 N·m (2.0 kg-m, 14 ft-lb)
Revision: November 20132014 Altima NAM

WATER PUMPCO-47
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
4. Turn the crankshaft pulley approximately 20
° clockwise so that
the timing chain on the timing chain tensioner side is loose.
5. Apply engine oil to the oil feed hole and timing chain tensioner and install the timing chain tensioner.
6. Remove the stopper pin (A).
7. Install valve timing control cover (bank 1) and water pump cover.
a. Before installing, remove all traces of liquid gasket from mating surface of water pump cover and IVT cover using a scraper.
Also remove traces of liquid gasket from the mating surface of the front cover.
b. Apply a continuous bead of liquid gasket to mating surface of IVT cover and water pump cover. Use Gen-
uine RTV Silicone Sealant or equivalent. Refer to GI-21, "Recommended Chemical Products and
Sealants".
CAUTION:
• Installation should be done within 5 minutes afte r applying liquid gasket.
• Do not fill the engine with oil for at least 30 minutes after the co mponents are installed to allow
the sealant to cure.
8. Install water drain plug (A) and copper sealing washer (B). CAUTION:
Do not reuse copper sealing washers.
9. Installation of remaining components is in the reverse order of removal. • After installation, refill coolant and check for leaks. Refer to CO-36, "Changing Engine Coolant"
and CO-
35, "System Inspection".
CAUTION:
Do not spill coolant in en gine compartment. Use a sh op cloth to absorb coolant.
• After starting engine, let idle for three minutes, then rev engine up to 3,000 rpm under no load to purge air from the high-pressure chamber of the chai n tensioner. The engine may produce a rattling noise.
This indicates that air still remains in the chamber and is not a matter of concern.
INSPECTION AFTER INSTALLATION
• Before starting engine, check oil/fluid levels incl uding engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-11, "FOR USA AND CANADA : Fluids and Lubricants"
.
PBIC0848E
AWBIA0905ZZ
: Front
Water drain plug (A) : Refer to EM-224, "Disas-
sembly and Assembly".
AWBIA1202GB
Revision: November 20132014 Altima NAM

SYSTEMEC-49
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
The ECM receives information such as the injecti
on pulse width and camshaft position sensor (PHASE) sig-
nal. Computing this information, ignition si gnals are transmitted to the power transistor.
During the following conditions, the ignition timing is revi sed by the ECM according to the other data stored in
the ECM.
• At starting
• During warm-up
•At idle
• At low battery voltage
• During acceleration
The knock sensor retard system is designed only for emergencies. The basic ignition timing is programmed
within the anti-knocking zone, if recommended fuel is used under dry conditions. The retard system does not
operate under normal driving conditions. If engine knocking occurs, the knock sensor monitors the condition.
The signal is transmitted to the ECM. The ECM retards the ignition timing to eliminate the knocking condition.
INTAKE VALVE TIMING CONTROL
INTAKE VALVE TIMING CONTROL : System DescriptionINFOID:0000000009462096
INTAKE VALVE TIMING CONTROL
System Diagram
Input/Output Signal Chart
*: This signal is sent to the ECM through CAN communication line
JPBIA4760GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed and piston position
Intake valve
timing control Intake valve timing control
solenoid valve
Camshaft position sensor (PHASE)
Engine oil temperature sensor Engine oil temperature
Engine coolant temperature sensor Engine coolant temperature
Combination meter Vehicle speed*
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-572
< SYSTEM DESCRIPTION >[VQ35DE]
SYSTEM
*: ECM determines the start signal status by the signals of engine speed and battery voltage.
SYSTEM DESCRIPTION
Ignition order: 1 - 2 - 3 - 4 - 5 - 6
The ignition timing is controlled by the ECM to maintain the best air-fuel ratio for every running condition of the
engine. The ignition timing data is stored in the ECM.
The ECM receives information such as the injection pulse width and camshaft position sensor (PHASE) sig-
nal. Computing this information, ignition si gnals are transmitted to the power transistor.
During the following conditions, the ignition timing is re vised by the ECM according to the other data stored in
the ECM.
• At starting
• During warm-up
• At idle
• At low battery voltage
• During acceleration
The knock sensor retard system is designed only for emergencies. The basic ignition timing is programmed
within the anti-knocking zone, if recommended fuel is used under dry conditions. The retard system does not
operate under normal driving conditions. If engine knocking occurs, the knock sensor monitors the condition.
The signal is transmitted to the ECM. The ECM retards the ignition timing to eliminate the knocking condition.
AIR CONDITIONING CUT CONTROL
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed
*
Ignition timing
control Ignition coil
(with power transistor)
Camshaft position sensor
(PHASE) Piston position
Mass air flow sensor Amount of intake air
Engine coolant temperature sensor Engine coolant temperature
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Transmission range switch Gear position
Battery Battery voltage
*
Knock sensor Engine knocking
Combination meter Vehicle speed CAN communi-
cation
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PRECAUTIONSEM-7
< PRECAUTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
• After removing the bolts and nuts, separate the mating surface and
remove the liquid gasket using Tool (A).
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to lightly tap (1) the cutter where the liquid gasket is applied. Use a
plastic hammer to slide (2) the cutter by tapping on the side.
CAUTION:
Do not damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using a scraper, remove the old liquid gasket adhering to the gasket application surface and the mating surface.
• Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts, and bolt holes.
2. Thoroughly clean the gasket application surface and the mating surface and remove adhering moisture, grease and foreign
materials.
3. Attach the liquid gasket tube to the tube presser. Use Genuine Silicone RTV Seal ant or equivalent. Refer to
GI-21, "Recommended Chemical Products and Sealants"
.
4. Apply the liquid gasket using suitable tool without breaks to the specified location.
• If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
• As for the bolt holes, normally apply the liquid gasket inside the holes. If specified, it should be applied outside the holes.
Make sure to read the text of this manual.
• Within five minutes of the liquid gasket application, install the mating component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• After 30 minutes or more have passed from the installation, fill the engine with the specified oil and coolant. Refer to MA-11,
"FOR USA AND CANADA : Fluids and Lubricants".
CAUTION:
If there are more specific instruct ions in the procedures contained in this manual concerning liquid
gasket application, observe them. Tool Number (A): KV10111100 (J-37228)
AWBIA1249GB
PBIC0003E
EMA0622D
SEM159F
Revision: November 20132014 Altima NAM

EM-38
< REMOVAL AND INSTALLATION >[QR25DE]
OIL PAN AND OIL STRAINER
18. Remove the oil strainer bolts in the reverse order as shown then
remove the oil strainer.
19. Remove rear cover plate, and four engine-to transaxle bolts, using power tool.
20. Loosen the upper oil pan bolts in the order shown using power tool.
21. Remove upper oil pan using Tool (A). • Remove the three O-rings from the upper oil pan and front
cover.
CAUTION:
Be careful not to damage the mating surfaces.
NOTE:
In areas where the cutter is difficult to use, use a plastic hammer
to lightly tap (1) the cutter where the liquid gasket is applied. Use
a plastic hammer to slide (2) the cutter by tapping on the side.
INSPECTION AFTER REMOVAL
Clean the oil strainer screen to remove any foreign material.
INSTALLATION
1. Apply Genuine Silicone RTV Sealant or equivalent to the upper oil pan at the specified sealant bead diameter (A) as shown.
Refer to GI-21, "Recommended Chemical Products and Seal-
ants".
CAUTION:
• Install two new O-rings in the upper oil pan and a new O- ring in the front cover.
• Do not reuse O-rings.
• Installation should be done within 5 minutes after apply- ing liquid gasket.
• Do not fill the engine with oil for at least 30 minutes after the co mponents are installed to allow
the liquid gasket to cure.
AWBIA1382ZZ
ALBIA0832GB
Tool number : KV10111100 (J-37228)AWBIA1249GB
Sealant bead
diameter (A) : 4.0 - 5.0 mm (0.157 - 0.197 in)
AWBIA1371ZZ
Revision: November 20132014 Altima NAM

OIL PAN AND OIL STRAINEREM-39
< REMOVAL AND INSTALLATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
2. Install the upper oil pan to the block and tighten the upper oil pan
bolts to specification in the order shown.
3. Apply Genuine Silicone RTV Sealant or equivalent to the lower oil pan at the specified sealant bead diameter (A) as shown.
Refer to GI-21, "Recommended Chemical Products and Seal-
ants".
CAUTION:
• Installation should be done within 5 minutes after apply-
ing liquid gasket.
• Do not fill the engine with oi l for at least 30 minutes after
the components are installed to allow the liquid gasket to
cure.
4. Install the lower oil pan to the upper oil pan and tighten the lower oil pan bolts to specification in the numerical order shown.
5. Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
Check for engine oil leaks with the engine at operating temperature and running at idle.
All bolts except 18 and 19 : 21.6 N·m (2.2 kg-m, 16.0 ft-
lb)
Bolts 18 and 19 : 8.8 N·m (0.90 kg-m, 78.0 in- lb)
ALBIA0832GB
Sealant bead
diameter (A) : 4.0 - 5.0 mm (0.157 - 0.197 in)ALBIA0834GB
ALBIA0830GB
Revision: November 20132014 Altima NAM

EM-56
< REMOVAL AND INSTALLATION >[QR25DE]
CAMSHAFT
c. Apply liquid gasket to the positions shown. Refer to
GI-21, "Rec-
ommended Chemical Products and Sealants".
d. Install valve timing control cover. • Tighten the bolts to specification in the numerical order asshown.
9. Check and adjust valve clearances. Refer to EM-23, "Camshaft valve clearance"
.
10. Install camshaft position sensor bracket.
a. Apply liquid gasket to camshaft position sensor bracket as shown.
CAUTION:
• Use Genuine Silicone RTV Seal ant, or equivalent. Refer to
GI-21, "Recommended Chemical Products and Sealants"
.
• After installation be sure to wipe off excessive liquid gas-
ket leaking from part (B).
• Installation should be done within 5 minutes after apply-
ing liquid gasket.
• Do not fill the engine with oil for at least 30 minutes after the co mponents are installed to allow
the liquid gasket to cure.
b. Tighten bolts to specification in numerical order shown.
11. Install the camshaft position sensors.
12. Installation of the remaining components is in the reverse order of removal.
Inspection After InstallationINFOID:0000000009460494
Inspection of Camshaft Sprocket (INT) Oil Gr oove and Camshaft Sprocket (EXH) Oil Groove
Diameter (A) : 3.4 - 4.4 mm (0.134 - 0.173 in)
AWBIA1362ZZ
ALBIA0839GB
(A) : 2.0 - 3.0 mm (0.079-0.118)
(B) : 10.5 mm (0.413 in)
Camshaft position
sensor bracket bolts : 10.41 N·m (1.1 kg-m, 8.0 ft-lb)
ALBIA0907GB
ALBIA0908GB
Revision: November 20132014 Altima NAM