2014 MITSUBISHI OUTLANDER SPORT reset

MITSUBISHI Remote Control*
Charging 3-17
3
E08304200026
The MITSUBISHI Remote Control allows tooperate the vehicle within the communicationrange of the wireless LAN device (whichconforms to IEEE 802.11b and supports iOSor Android). The following operations areavailable.
zCharging timerIf you specify the charge start and/or stoptime with the normal charge cable con-nected, charging is started and/or stoppedat that time.zRemote climate controlBy setting the remote climate control tooperate at a predetermined time, cabincomfort can be improved or visibility canbe ensured (defrosting/demisting) beforegetting on the vehicle.
Normal charging is discontinued.
There is no power coming from the outlet.
There may have been a electrical power failure, or the breaker may have failed.Charging will resume when the power source is reset.
The EV charging cable has been disconnected.
Check that the EV charging cable has not been disconnected.
The button on the normal charge connector has been pressed.
If the charge connector button is pressed for a long period of time, charging will be stopped. Start the charging procedure again.
The temperature of the drive battery is too high or too low to charge.
Confirm the drive battery temperature.Refer to “Cautions and actions to deal with intense heat” on page 2-8 and “Cautions and actions to deal with intense cold” on page 2-9.
Charging is stopped by the normal charge timer.
Charging will stop depending on the timer function setting of the normal charge device. If you need to charge the drive battery more, start the charging procedure again.
The Charging timer was set up by the MITSUBISHI Remote Control after starting of normal charging.
Cancel all the charging timer settings. Charging is automatically restarted if you cancel the charging timer.
Symptom
Possible cause
Possible solution
MITSUBISHI Remote Con-trol
*
1- Wireless LAN device2- Antenna
BK0203201EN.book 17 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

MITSUBISHI Remote Control*3-20 Charging
3
zWhen the auxiliary battery is removed, thetimer control of the MITSUBISHI RemoteControl is reset and each function of theMITSUBISHI Remote Control can not beused. Also the drive battery can not bewarmed up.Communicate the wireless LAN device andyour vehicle again.NOTE
BK0203201EN.book 20 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-11
6
To r e t u r n t h e d i s p l a y t o 0 , h o l d d o w n t h emulti information display switch for about 2seconds or more. Only the currently dis-played value will be reset.ExampleIf tripmeter is displayed, only tripmeter
will be reset.
E00522502021
Displays the approximate time until the nextperiodic inspection recommended by
MITSUBISHI MOTORS. “---” is displayedwhen the inspection time has arrived.
1. Displays the time until the next periodicinspection.2. This informs you that a periodic inspec-tion is due. We recommend you to consulta MITSUBISHI MOTORS AuthorisedService Point.At that time, when the operation mode ischanged from OFF to ON, the warningdisplay is displayed for a few seconds onthe information screen.3. After your vehicle is inspected at aMITSUBISHI MOTORS Authorised Ser-vice Point, it displays the time until thenext periodic inspection.
The “---” display can be reset while the oper-ation mode of the power switch is in OFF.
Example usage of tripmeter and tripmeter
It is possible to measure two currentlytravelled distances, from home using trip-meter and from a particular point onthe way using tripmeter .
To r e s e t t h e t r i p m e t e r
NOTE
zWhen disconnecting the auxiliary battery ter-minal, the memory of tripmeter and are cleared, and the display returns to “0”.
Service reminder
NOTE
zDepending on the vehicle specifications, thedisplayed time may differ from the next peri-odic inspection time recommended byMITSUBISHI MOTORS.In addition, the display settings for the nextperiodic inspection time can be modified.To modify the display settings, have itadjusted at a MITSUBISHI MOTORSAuthorised Service Point.For more details, consult a MITSUBISHIMOTORS Authorised Service Point.
NOTE
zThe distance is show
n in units of 100 km
(100 miles). The time is
shown in units of
months.
To r e s e t
BK0203201EN.book 11 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-12 Instruments and controls
6
When the display is reset, the time until thenext periodic inspection is displayed and thewarning display is no longer displayed whenthe operation mode is changed from OFF toON.1. When you lightly press the multi informa-tion display switch a few times, the infor-mation screen switches to the servicereminder display screen.2. Press and hold the multi information dis-play switch for about 2 seconds or more todisplay “ ” and make it flash. (If there isno operation for about 10 seconds withflashing, the display returns to the previ-ous screen.)
3. Lightly press the multi information dis-play switch while the icon is flashing tochange the display from “---” to“CLEAR”. After this, the time until thenext periodic inspection will be displayed.
E00531001038
When the operation mode is put in ON, thesystem check screen is displayed for about 4seconds. If there is no fault, informationscreen (when the operation mode is ON) isdisplayed.If there is a fault, the screen changes to warn-ing display.Refer to “Warning display list” on page 6-22.
CAUTIONzThe customer is responsible for making surethat periodic inspection and maintenance areperformed.Inspections and maintenance must be per-formed to prevent accidents and malfunc-tions.NOTE
z“---” display cannot be reset when the opera-tion mode is in ON.zWhen “---” is displayed, after a certain dis-tance and a certain period of time, the dis-play is reset and the time until the nextperiodic inspection is displayed.
zIf you accidentally reset the display, we rec-ommend you to consult a MITSUBISHIMOTORS Authorised Service Point.
System check screen
NOTE
zThe system check screen display variesdepending on the customer’s equipment.NOTE
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-13
6
E00537600026
This displays the approximate driving range(how many more kilometres or miles you candrive).EV cruising range display (A)This displays the distance that can be traveledwith the remaining power in the drive battery.To t a l c r u i s i n g r a n g e d i s p l a y ( B )This displays the distance that can be traveledwith the remaining power in the drive batteryand the remaining amount of fuel.
E00531201072
This displays the average fuel consumptionfrom the last reset to the present time.There are the following 2 mode settings.Refer to “Changing the reset mode for aver-age fuel consumption” on page 6-16.For information on how to change the aver-age fuel consumption display setting, refer to“Changing the function settings” on page6-15.
EV cruising range display/Total cruising range display
NOTE
zThe driving range may vary depending onthe driving conditions
and habits. Treat the
distance displayed as just a rough guideline. zWhen the drive battery is charged or thevehicle is refueled, th
e cruising range display
is updated. However, if the charge level islow or the refueling amount is small, it can-not be updated correctly. Fully charge thebattery or refill to full tank whenever possi-ble.
zOn rare occasions, the value displayed forthe driving range may change if you areparked on an extremely steep incline. This isdue to the movement of fuel in the tank anddoes not indicate any malfunction.zThe display setting can be changed to thepreferred units (km or miles).Refer to “Changing the function settings” onpage 6-15.zWhen the EV cruising range falls belowapproximately 1 km (1 mile), the EV cruis-ing range display shows “---”.zWhen the total cruising range falls belowapproximately 50 km (30 miles), the totalcruising range disp
lay shows “---”.
Av e r a g e f u e l c o n s u m p t i o n d i s -play
NOTE
NOTE
zThe average fuel consumption display can bereset separately for the auto reset mode andfor the manual reset mode.z“---” is displayed when the average fuel con-sumption cannot be measured or when it is99.9 L/100 km (99.9 miles) or more.zThe initial (default) setting is “Auto resetmode”.zThe average fuel consumption will dependon the driving conditions (road conditions,how you drive, etc.). The displayed fuel con-sumption may vary from the actual fuel con-sumption. Treat the fuel consumptiondisplayed as just
a rough guideline.
zThe memory of the auto reset mode or man-ual reset mode for the average fuel consump-tion display is erased if the auxiliary batteryis disconnected.zThe display setting can be changed to thepreferred units {km/L, mpg (US), mpg (UK)or L/100 km}.Refer to “Changing the function settings” onpage 6-15.
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-15
6
The display shows the score you achieved inthe last several minutes.[When the operation mode is put in OFF]The display shows the overall ECO score thefunction has counted from the time when theoperation mode is set to “ON” to the timewhen it is set to “OFF”.
E00522701736
The “Display language”, “Temperature unit”,“Fuel consumption unit”, and “Average fuelconsumption and speed reset method” etc.setting can be modified as desired.1. Stop the vehicle in a safe place.Firmly apply the parking brake, and pressthe electrical parking switch and shift to“P” (PARK) position.
2. Lightly press the multi information dis-play switch a few times to switch theinformation screen to the function settingscreen.Refer to “Information screen” on page6-7.3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.
Changing the function settings
ECO drive level
Low
High
CAUTIONzFor safety, stop the ve
hicle before operating.
While driving, even if you operate the multiinformation display switch, the function set-ting screen is not displayed.
NOTE
zTo r e t u r n t h e m e n u s c r e e n t o t h e f u n c t i o n s e t -ting screen, press and hold the multi infor-mation display switch fo
r about 2 seconds or
more.zIf no operations are made within about 30seconds of the menu sc
reen being displayed,
the display returns to the function settingscreen.
BK0203201EN.book 15 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-16 Instruments and controls
6
4. Select the item to change on the menuscreen and change to the desired setting.Refer to the following items for furtherdetails on the operation methods.Refer to “Changing the reset mode foraverage fuel consumption” on page 6-16.Refer to “Changing the fuel consumptiondisplay unit” on page 6-17.Refer to “Changing the temperature unit”on page 6-17.Refer to “Changing the display language”on page 6-18.Refer to “Changing the language coopera-tive control” on page 6-18.Refer to “Operation sound setting” onpage 6-19.Refer to “Changing the time until “RESTREMINDER” is displayed” on page 6-19.Refer to “Changing the turn-signal sound”on page 6-20.Refer to “Returning to the factory set-tings” on page 6-20.
E00522902054
The mode conditions for the average fuelconsumption display can be switchedbetween “Auto reset” and “Manual reset”.1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “AVG (average fuelconsumption)”.
3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from A/1 (Auto reset mode) toM/2/P (Manual reset mode), or fromM/2/P to A/1.The setting is changed to the selectedmode condition.zWhen the average fuel consumption isbeing displayed, if you hold down themulti information display switch, theaverage fuel consumption displayed atthat time is reset.zWhen the operation mode is changedfrom ACC or OFF to ON, the mode set-ting is automatically switched from man-ual to auto.Switching to auto occurs automatically. Ifswitching to manual mode is done, how-ever, the data from the last reset is dis-played.zWhen the average fuel consumption isbeing displayed, if you hold down themulti information display switch, theaverage fuel consumption displayed atthat time is reset.
NOTE
zIf the auxiliary battery is disconnected, thesefunction settings are reset from memory andis automatically to the factory settings.
Changing the reset mode for aver-age fuel consumption
Manual reset modeAuto reset mode
BK0203201EN.book 16 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-17
6
zWhen the operation mode is in ACC orOFF for about 4 hours or longer, the aver-age fuel consumption display is automati-cally reset.
E00523001778
The display unit for fuel consumption can beswitched. The distance and amount units arealso switched to match the selected fuel con-sumption unit.1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.
2. Lightly press the multi information dis-play switch to select “AVG UNIT (fuelconsumption display setting)”.3. Press and hold the multi information dis-play switch for about 2 seconds or more todisplay “AVG UNIT”.4. Lightly press the multi information dis-play switch to select the units.5. Press and hold the multi information dis-play switch for about 2 seconds or more tochange the setting to the selected unit.
The distance units is also switched in the fol-lowing combinations to match the selectedfuel consumption unit.
E00523101737
The display unit for temperature can beswitched.1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “ ” (temperatureunit setting).
NOTE
zThe average fuel consumption display can bereset separately for the auto reset mode andfor the manual reset mode.zThe memory of the auto reset mode or man-ual reset mode for the average fuel consump-tion display is erased if the auxiliary batteryis disconnected.
Changing the fuel consumption display unit
NOTE
zThe display units for the average fuel con-sumption and the driving range is switched,but the units for the indicating needle (speed-ometer), the odometer and the tripmeter willremain unchanged.
Fuel consumption
Distance
(driving range)
L/100 km
km
mpg (US)
mile (s)
mpg (UK)
mile (s)
km/L
km
Changing the temperature unit
BK0203201EN.book 17 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分