2014 MITSUBISHI OUTLANDER SPORT warning

Multi information display
Instruments and controls 6-11
6
To r e t u r n t h e d i s p l a y t o 0 , h o l d d o w n t h emulti information display switch for about 2seconds or more. Only the currently dis-played value will be reset.ExampleIf tripmeter is displayed, only tripmeter
will be reset.
E00522502021
Displays the approximate time until the nextperiodic inspection recommended by
MITSUBISHI MOTORS. “---” is displayedwhen the inspection time has arrived.
1. Displays the time until the next periodicinspection.2. This informs you that a periodic inspec-tion is due. We recommend you to consulta MITSUBISHI MOTORS AuthorisedService Point.At that time, when the operation mode ischanged from OFF to ON, the warningdisplay is displayed for a few seconds onthe information screen.3. After your vehicle is inspected at aMITSUBISHI MOTORS Authorised Ser-vice Point, it displays the time until thenext periodic inspection.
The “---” display can be reset while the oper-ation mode of the power switch is in OFF.
Example usage of tripmeter and tripmeter
It is possible to measure two currentlytravelled distances, from home using trip-meter and from a particular point onthe way using tripmeter .
To r e s e t t h e t r i p m e t e r
NOTE
zWhen disconnecting the auxiliary battery ter-minal, the memory of tripmeter and are cleared, and the display returns to “0”.
Service reminder
NOTE
zDepending on the vehicle specifications, thedisplayed time may differ from the next peri-odic inspection time recommended byMITSUBISHI MOTORS.In addition, the display settings for the nextperiodic inspection time can be modified.To modify the display settings, have itadjusted at a MITSUBISHI MOTORSAuthorised Service Point.For more details, consult a MITSUBISHIMOTORS Authorised Service Point.
NOTE
zThe distance is show
n in units of 100 km
(100 miles). The time is
shown in units of
months.
To r e s e t
BK0203201EN.book 11 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-12 Instruments and controls
6
When the display is reset, the time until thenext periodic inspection is displayed and thewarning display is no longer displayed whenthe operation mode is changed from OFF toON.1. When you lightly press the multi informa-tion display switch a few times, the infor-mation screen switches to the servicereminder display screen.2. Press and hold the multi information dis-play switch for about 2 seconds or more todisplay “ ” and make it flash. (If there isno operation for about 10 seconds withflashing, the display returns to the previ-ous screen.)
3. Lightly press the multi information dis-play switch while the icon is flashing tochange the display from “---” to“CLEAR”. After this, the time until thenext periodic inspection will be displayed.
E00531001038
When the operation mode is put in ON, thesystem check screen is displayed for about 4seconds. If there is no fault, informationscreen (when the operation mode is ON) isdisplayed.If there is a fault, the screen changes to warn-ing display.Refer to “Warning display list” on page 6-22.
CAUTIONzThe customer is responsible for making surethat periodic inspection and maintenance areperformed.Inspections and maintenance must be per-formed to prevent accidents and malfunc-tions.NOTE
z“---” display cannot be reset when the opera-tion mode is in ON.zWhen “---” is displayed, after a certain dis-tance and a certain period of time, the dis-play is reset and the time until the nextperiodic inspection is displayed.
zIf you accidentally reset the display, we rec-ommend you to consult a MITSUBISHIMOTORS Authorised Service Point.
System check screen
NOTE
zThe system check screen display variesdepending on the customer’s equipment.NOTE
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display6-18 Instruments and controls
6
3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch in from °C to °F, or from °F to °C.The setting is changed to the selected tem-perature unit.
E00523201741
The language of the multi information displaycan be switched.
1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “LANGUAGE” (lan-guage setting).3. Press and hold the multi information dis-play switch for about 2 seconds or more todisplay “LANGUAGE”.4. Lightly press the multi information dis-play switch to select the desired language.
5. If you hold down the multi informationdisplay switch for about 2 seconds ormore, the setting is changed to theselected language.
E00523301625
The language used in the Bluetooth
®2.0
interface (if so equipped) can be changedautomatically to the same language as thatshown in the multi information display.1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.
NOTE
zThe temperature value on air conditionerpanel is switched in
conjunction with outside
temperature display unit of the multi infor-mation display.However, “°C” or “°F” are not shown to tem-perature display of an air conditioner.zOn vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), the tem-perature value of the air conditioner screenof Mitsubishi Multi-Communication System(MMCS) is switched
in conjunction with
outside temperature display unit of the multiinformation display.However, “°C” or “°F” are not shown to theair conditioner screen.
Changing the display language
NOTE
zIf “---” is selected in the language setting, awarning message is not
displayed when there
is a warning display or interrupt display.
Changing the language coopera-tive control
BK0203201EN.book 18 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Multi information display
Instruments and controls 6-19
6
2. Lightly press the multi information dis-play switch to select “ ” (languagecooperative control).3. Press and hold the multi information dis-play switch to switch from A (languagecooperation enabled) to M (languagecooperation disabled), or from M to A.The setting is changed to the selected con-dition.
E00523400690
Yo u c a n t u r n o f f t h e o p e r a t i o n s o u n d s o f t h emulti information display switch and rheostatillumination button.
1. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from the setting mode screen to themenu screen.Refer to “Changing the function settings”on page 6-15.2. Lightly press the multi information dis-play switch to select “ ” (operationsound setting).3. Press and hold the multi information dis-play switch for about 2 seconds or more toswitch from ON (operation sound on) toOFF (operation sound off), or from OFFto ON.The setting is changed to the selected con-dition.
E00523501702
The time until the display appears can bechanged.
NOTE
zThe language display modified with the lan-guage setting can be switched in the follow-ing manner.
•When A (language
cooperation enabled)
has been selected with the language cooper-ative control, the language for theBluetooth
®2.0 interface (if so equipped) is
automatically changed to the languageselected for the multi information display.However, this changing function may notwork depending on the language selectedfor the multi information display.•When M (language c
ooperation disabled)
has been selected with the language cooper-ative control, the language for theBluetooth
®2.0 interface (if so equipped) is
not automatically changed to the languageselected for the multi information display.
zThe language on the disp
lay of the audio sys-
tem (if so equipped) is not automaticallychanged even if you
select A (language
cooperation enabled) of
the language cooper-
ation control.
Operation sound setting
NOTE
NOTE
zThe operation sound setting only deactivatesthe operation sound of the multi informationdisplay switch and rheostat illumination but-ton. The warning di
splay and other sounds
cannot be deactivated.
Changing the time until “REST REMINDER” is displayed
BK0203201EN.book 19 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-21
6
E00523701182E00523802034
Indicator lamp, warning lamp, and information screen display list Indicator and warning lamp list 1- Position lamp indicator lamp
m P. 6-37
2- Front fog lamp indicator lamp
m P. 6-37
3- Turn-signal indicator lamps/Hazard
warning indicator lamps
m P. 6-36
4- Rear fog lamp indicator lamp
*
m P. 6-37
5- High-beam indicator lamp
m P. 6-37
6- Plug-in Hybrid EV System warning
lamp
m P. 6-39
7- Auxiliary battery charge warning lamp
m P. 6-39
8- Charging indicator
m P. 6-37
9- Regenerative brake warning lamp
m P. 6-39
10- Ready indicator
m P. 6-37
11- Acoustic Vehicle Alerting System
(AVAS) OFF indicator lamp
m P. 7-24
12- Active Stability Control (ASC) indica-
tor lamp
m P. 7-34
13- Active Stability Control (ASC) OFF
indicator lamp
m P. 7-34
14- Anti-lock brake system (ABS) warning
lamp
m P. 7-30
15- Supplemental restraint system (SRS)
warning lampm P. 5-30
16- Check engine warning lamp
m P. 6-38
17- Seat belt warning lamp
m P. 5-11
18- Brake warning lamp
m P. 6-37
BK0203201EN.book 21 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-22 Instruments and controls
6
E00523901344
When there is information to be announced, such as lamp reminder, the buzzer sounds and the screen switches to the displays sho
wn below. Refer
to the appropriate page and take the necessary measures.When the cause of the warning display is eliminated, the warning display goes out automatically.Refer to “Warning display list” on page 6-22.Refer to “Navigation information display” on page 6-32.Refer to “Other interrupt displays” on page 6-33.
E00524001993
19- Information screen display list
m P. 6-22
Information screen display list
NOTE
zA warning may be displayed on the in
formation screen and the buzzer ma
y sound in the following rare cases.
This is caused by the system picking up inte
rference such as noise or strong electromagnetic waves, and is not a functional pro
blem.
•An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a rad
ar station.
•Abnormal voltage or a static electricity
discharge is generated by th
e operation of installed elect
rical equipment (including
after-market parts).
If the warning display appears many times,
we recommend you to consult a MITSUBISHI MOTORS Authorised Service Point.
Warning display li st
Screen
Cause
Solution (Reference)
zOne or more minor failure is occurring in the Plug-in Hybrid EV System.
zHave your vehicle inspected by a MIT-SUBISHI MOTORS Authorised Service Point.
BK0203201EN.book 22 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-23
6
zOne or more failure is occurring in the Plug-in Hybrid EV System.
zImmediately park the vehicle in a safe place and contact a MITSUBISHI MOTORS Authorised Service Point.
zThe parking lock unit is in failure. The Plug-in Hybrid EV system cannot be kept in standstill condition without applying the parking brake.
zPark the vehicle at a safe, flat place and apply the parking brake. Contact a MIT-SUBISHI MOTORS Authorised Service Point.Refer to “Electrical parking switch” on page 7-16.
zYo u a r e a t t e m p t i n g t o s e t t h e o p e r a t i o n mode to “ON” when the charge connector is connected to the charge port.
zDisconnect the charge connector from the charge port before operating the power switch.
zCharging was interrupted due to system failure (electric leak detected).
zThere is an electric leak or the normal charge cable is faulty. Immediately stop using the cable and contact a MITSUBI-SHI MOTORS Authorised Service Point.
zCharging was interrupted due to poor con-nection of the charge cable or power fail-ure.
zConnect the charge cable correctly.Refer to “Normal charging” on page 3-8.zIf charging is interrupted due to a power failure, charging will be automatically resumed when the power is restored.
Screen
Cause
Solution (Reference)
BK0203201EN.book 23 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-24 Instruments and controls
6
zThe drive battery temperature is too cold.
zWhen the vehicle is under running, stop the vehicle at a safe place and contact a MIT-SUBISHI MOTORS Authorized Service Point.zWhen the vehicle is in parking, in the day-time, wait for the outside temperature to rise and re-start the Plug-in hybrid system if the outside temperature has been risen.Refer to “Cautions and actions to deal with intense cold” on page 2-9.
zYo u h a v e f o r g o t t e n t o t u r n o f f t h e l a m p s . R e f e r t o “ L a m p s ( h e a d l a m p s , f o g l a m p , e t c . )
auto-cutout function” on page 6-40.
zThere is a fault in the keyless operation system.
Refer to “Keyless operation system” on page 4-6.
Screen
Cause
Solution (Reference)
BK0203201EN.book 24 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分