2014 MITSUBISHI OUTLANDER SPORT stop start

Security alarm system*
Locking and unlocking 4-25
4
(The buzzer sounds intermittently and thesecurity indicator (A) blinks.)
The system preparation time extends from thepoint at which all of the doors and the tailgateare locked by pressing of the LOCK switchon the remote control switch or the keylessoperation function to the point at which thesystem armed mode goes into effect.During this time, it is possible to temporarilyopen a door or the tailgate without using thekeyless entry system or the keyless operationfunction and without causing the alarm tosound (for example, when you forget some-thing inside the vehicle or realize that a win-dow is open).(The buzzer stops and the security indicatorcontinues to blink with the indicator’sreduced lit-up duration time.)Once the system preparation mode has ended,the system armed mode starts.
zIf the turn-signal lamps do not blink after thelocking and unlocking operation using thekeyless entry system or
the keyless operation
function, the security alarm system may bemalfunctioning.Have the vehicle inspected at aMITSUBISHI MOTORS Authorised ServicePoint.If the confirmation function (blinking of theturn-signal lamps by
locking and unlocking
the doors and the tailgate) is deactivated, theturn-signal lamps do not blink after the lock-ing and unloc
king operation.
For information on the confirmation func-tion, refer to “Keyless entry system” onpages 4-3 and “To opera
te using the keyless
operation function”
on page 4-9.
zThe security alarm system could be activatedin the following situations.•Using a car washer•Taking the vehicle on a ferry•Parking in an automated car park•Leaving someone or a pet in the vehicle•Leaving a window or the sunroof open• Leaving an unstable object such as a stuffedtoy or accessory in the vehicle• Suffering a continuous impact or vibrationby hail, thunder, etc.NOTE
• Air flows by the Remote Climate Control.According to the situations, please deacti-vate the vehicle inclination detection func-tion and the interior intrusion detectionfunction.Refer to “To deactivate the vehicle inclina-tion detection function and the interiorintrusion detection f
unction” on page 4-27.
zThe sensitivity of the interior intrusiondetection function can be adjusted. For fur-ther details, please contact a MITSUBISHIMOTORS Authorised Service Point.
The security alarm has four modes:

System preparation mode (approx. 20 seconds)

NOTE
System armed mode

BK0203201EN.book 25 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Security alarm system*
Locking and unlocking 4-27
4
By locking the vehicle using the keylessentry system or the keyless operationfunction, the system preparation mode isactivated.The buzzer makes an intermittent beepingsound and the security indicator (D) in thecentre panel flashes for confirmation.
4. After approximately 20 seconds, thebuzzer stops, and when the blinking of thesecurity indicator starts to slow down, thesystem armed mode goes into effect.The security indicator continues to blinkduring the system armed mode.
E00312101416
The vehicle inclination detection function andthe interior intrusion detection function canbe deactivated when parking in automated carparks or leaving pets in the vehicle or leavingthe vehicle with the windows slightly open.1. Put the operation mode in OFF.2. Raise and hold the wiper and washerswitch to the “MIST” position for about 3seconds. The buzzer will sound once andthe function will be deactivated.
To a c t i v a t e t h e f u n c t i o n a g a i n , r a i s e a n d h o l dthe wiper and washer switch to the “MIST”position for about 3 seconds.The buzzer will sound twice and the functionwill be activated.
Ta i l g a t e L O C K s w i t c h
*
NOTE
zThe system preparation mode is not activatedwhen the doors and the tailgate have beenlocked using a method ot
her than the keyless
entry system or the keyless operation func-tion (namely a key, the inside lock knob orthe central door lock switch).zIf the bonnet is open, the security indicatorilluminates, and the system does not enterthe system preparation mode.When the bonnet is closed, the system entersthe system preparation mode, and after about20 seconds the system enters the systemarmed mode.NOTE
zThe security alarm system can be activatedwhen people are riding inside the vehicle orwhen the windows are open. To prevent acci-dental activation of the alarm, do not set thesystem to the system armed mode while peo-ple are riding in the vehicle.zAv o i d l e a v i n g v a l u a b l e i t e m s i n s i d e t h e v e h i -cle even when the secu
rity alarm system has
been set to the “active” mode.
To d e a c t i v a t e t h e v e h i c l e i n c l i n a -tion detection function and the interior intrusion detection func-tion

BK0203201EN.book 27 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Seat belts5-12 Seat and seat belts
5
E00405000420
The seat belt anchor height can be adjusted.Move the seat belt anchor down with the lockknob (A) depressed. To move the anchor up,slide it without depressing the lock knob (A).
E00405201113
The rear-centre 3-point type seat belt must beworn correctly as illustrated.
1. Pull out the buckle (C) from the seatback.2. Pull the seat belt and insert the small latchplate (A) into the buckle (C).
WA R N I N GzDo not install any accessory or sticker thatmakes the lamp difficult to see.NOTE
zIf the seat belt subse
quently remains unfas-
tened, the warning lamp and the tone willissue further warnings each time the vehiclestarts moving from a stop.zFor the front passenge
r seat, the warning
function works only while a person is sittingon the seat.zWhen luggage is placed on the front passen-ger seat, a sensor in the seat cushion may,depending on the weight
and position of the
luggage, cause the warning tone to soundand the warning lamp to come on.
Adjustable seat belt anchor (front seats)
WA R N I N GzWhen adjusting
the seat belt anchor, set it
at a position that is
sufficiently high so
that the belt will make full contact withyour shoulder but will not touch yourneck.
Rear-centre 3-point type seat belt Anchor down
Anchor up
WA R N I N GzBe sure to securely connect the both latchplate (A and B). Failing to do so could sig-nificantly reduce the amount of protectionand cause serious injures in a collision or asudden stop.
To f a s t e n
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-24 Instruments and controls
6
zThe drive battery temperature is too cold.
zWhen the vehicle is under running, stop the vehicle at a safe place and contact a MIT-SUBISHI MOTORS Authorized Service Point.zWhen the vehicle is in parking, in the day-time, wait for the outside temperature to rise and re-start the Plug-in hybrid system if the outside temperature has been risen.Refer to “Cautions and actions to deal with intense cold” on page 2-9.
zYo u h a v e f o r g o t t e n t o t u r n o f f t h e l a m p s . R e f e r t o “ L a m p s ( h e a d l a m p s , f o g l a m p , e t c . )
auto-cutout function” on page 6-40.
zThere is a fault in the keyless operation system.
Refer to “Keyless operation system” on page 4-6.
Screen
Cause
Solution (Reference)
BK0203201EN.book 24 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-26 Instruments and controls
6
zThe RBS (regenerative brake system) can-not be used.
zWe recommend you to consult a MITSUB-ISHI MOTORS Authorised Service Point.
zThere is a fault in the ABS.
zAv o i d s u d d e n b r a k i n g a n d h i g h - s p e e d d r i v -ing, stop the vehicle in a safe place, and take corrective measures. Refer to “ABS warning” on page 7-30.
zOne of the doors or the tailgate is not com-pletely closed.The open door is displayed.
zClose the door or tailgate.Refer to “Door ajar warning display screen” on page 6-9.
zThe bonnet is open.
zClose the bonnet.Refer to “Bonnet” on page 11-3.
zThere is a fault in the electronic immobi-lizer (Anti-theft starting system).
zPut the operation mode in OFF, and then start the Plug-in Hybrid EV System again.If the warning is not cancelled, please con-tact a MITSUBISHI MOTORS Authorised Service Point.
Screen
Cause
Solution (Reference)
BK0203201EN.book 26 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-28 Instruments and controls
6
zThe fuel is running low.
zRefuel as soon as possible. Refer to “Fuel remaining warning display” on page 6-10.
zYo u a r e d r i v i n g w i t h t h e p a r k i n g b r a k e s t i l l applied.
zRelease the parking brake. Refer to “Brake warning display” on page 6-39.
zThere is a fault in the engine oil circulation system.
zImmediately stop the vehicle in a safe place. We recommend you to have it checked.Refer to “Oil pressure warning display” on page 6-40.
zThere is a fault in the SRS airbag or the pre-tensioner system.
zWe r e c o m m e n d y o u t o h a v e i t c h e c k e d , immediately.Refer to “Supplemental restraint system (SRS) warning lamp” on page 5-30.
zThere is a fault in the active stability con-trol (ASC).
zWe r e c o m m e n d y o u t o h a v e i t c h e c k e d .Refer to “Active stability control (ASC)” on page 7-32.
zThere is a fault in the Hill start assist.
zWe r e c o m m e n d y o u t o h a v e i t c h e c k e d .Refer to “Hill start assist” on page 7-27.
Screen
Cause
Solution (Reference)
BK0203201EN.book 28 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-33
6
E00524201836
The operation status of each system is displayed on the information screen. Refer to the appropriate page for the system for fu
rther details.
Other interrupt displays
Screen
System operation status
Reference
zWhen operating the Plug-in Hybrid EV System, the selector lever is in a position other than the “P” (PARK) position, or you pressed the power switch without depress-ing the brake pedal.
zPlace the selector lever in the “P” (PARK) position, depress the brake pedal with the right foot. Then, press the power switch.Refer to “Starting and stopping the Plug-in Hybrid EV System” on page 7-12.
zDriving power is restricted by the safety system as the Plug-in Hybrid EV System has become too hot or too cold.
zYo u d o n o t h a v e t o t a k e a n y a c t i o n s . T h e restriction on the driving power will be released when the Plug-in Hybrid EV Sys-tem returns to the normal temperature.
zIf the vehicle had not been refueled about 15 litres or more at one time for a long time, the engine starts automatically for the maintenance and fuel system components.This display may appear frequently depending on the use conditions of your vehicle such as when the fuel has been staying in the fuel tank for a long time.When the engine is running, this display shows the state where the drive battery is charged, and the battery charge mode dis-play (
) is displayed.
zRefill the 15 litres more at one time. This display and battery charge mode display will disappear, and the engine will stop.
BK0203201EN.book 33 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamps6-36 Instruments and controls
6
The setting for rest interval can be changed.
E00501600100E00501701427
These indicator lamps blink inthe following situations.zWhen the turn-signal leveris moved to activate a turn-signal lamp.
Refer to “Turn-signal lever” on page 6-45.
zWhen the hazard warning flasher switchis pressed to activate the hazard warninglamps.Refer to “Hazard warning flasher switch”on page 6-45.
Screen
Solution
We r e c o m m e n d y o u t o h a v e i t c h e c k e d . R e f e r t o “ S e r v i c e r e m i n d e r ” f o r f u r t h e r d e t a i l s o n p a g e 6-11.
Screen
Solution
Stop the vehicle in a safe place, stop the Plug-in Hybrid EV system, and take a rest.Use this display as rough guide for taking rests during a long drive.The interval from the start of your trip until this message is displayed can be set.Refer to “Changing the time until “REST REMINDER” is displayed” on page 6-19.The display and buzzer alert the driver when the set time is reached. If you continue to drive without having a rest, the buzzer sounds about every 5 minutes to encourage you to take a rest.zIn the following cases, the time driven is reset and the display returns to the previous dis-play screen. After this, when the set time is reached again, the buzzer and display encourage you to take a rest.•The buzzer sounds 3 times.•Put the operation mode in OFF.• The multi information display switch is held for about 2 seconds or more.
Indicator lamps Tu r n - s i g n a l i n d i c a t o r lamps/Hazard warning indica-tor lamps BK0203201EN.book 36 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分