2014 AUDI Q7 Owner´s Manual

Sun shade
Applies to vehicles: with sun shade
The windows in the rear doors and the rear
window ore each equipped with a sun shade .
Fig. 63 Sun shade p ulled up on a rea r window
Fig . 6 4 Sun shade p ulled up on th e rear lid w in d ow
Sun shade (rear doors )
~ Pull the shade out and hang it in the b racket
on the upper door frame
r=;-, fig. 63 .
Sun sh ade (rear window )
~ Pull the shade out and hang i t in the bracket
on the rear lid frame
c> fig . 64 .
Clear vision 63
Wiper and washer
system
Switching the windshield wipers on
The windshield wiper lever controls both the
windshield wipers and the washer system.
F ig . 65 W inds hield w ipe r leve r
The windshield wiper l ever r=;-, fig. 65 has the
follow ing positions:
Acti vating rain sensor
~ Move the lever up to posit ion (!) .
~ Move switch @up or dow n to ad just the
sensitivity of the rain sensor.
L o w wiper speed
~ Move the lever up to posit ion @.
High w ipe r speed
~ Move the lever up to posit ion @.
One-touch wiping
~ Move the lever to position @ , when you
want to wipe the windshield
briefly .
Automat ic wiper /wa sher
~ Pull the lever to position ® (toward the
s t eer ing whee l) and hold.
~ Release the Lever . The washer stops and the
w ipers keep go ing for about four seconds.
Depending on how long the Lever is held ,
different numbers of wash cycles are per­
formed .
Turning off the w ipe rs
~ Move the lever back to position @ .

64 Clear vis ion
General information
The winds hield wipers and the w indshield
washer system operate only with the ignition
on.
During a temporary stop , e.g . at a t raff ic sig­
na l, the set wipe speed is automatically re­
duced by one stage.
The winds hield washer no zzles a re heated at
l ow temperatures when the ignition is on .
Removing w ate r droplet s
About 5 seconds after the wash cycle is com­
plete, the wiper system performs a single au ­
tomatic wipe cycle to remove any water drop­
l ets that remain on the windshield whi le dr iv ­
ing.
If you would like to deactivate this delayed
wipe cycle wh ile driving, you have to pull the
l eve r to pos ition ® again within 10 seconds
after this wipe cy cle.
Water droplet removal is reactivated after the
ignit ion is switched off and then on again .
Winter position
To speed up de -icing of the w indshield w ipers,
t hey move to the winter posi tion when the ig­
n ition is switched off and at an outside tem­
perature below 39
°F (4 °(). In this posit ion ,
the w indshield wipers are in an area on the
g lass w hich is reached by the a ir vents below
the glass. It is also easier to remove snow and
ice from the wi ndshield wipers in this posi­
tion .
The wipe rs leave the w inte r position, when
the ign ition is swi tc h ed on, if the winds hield
wiper lever is operated or the active rain sen­
sor reacts to moistu re.
Rain sensor
The rain senso r operates on ly in the inte rva l
wiper position . When it sta rts to ra in , the in­
terval wipe r mode is activated automati ca lly.
If the windshie ld w iper lever is in the inte rval
wipe posit ion w ith the ign ition switched off, the ra
in sensor is not activated until ve hicle
sp eed is above 4 mph (6 km/h).
T o red uce the sensi tivi ty of the rain senso r,
the switch @ mus t be moved down . T o in­
crease the sensitivity of the rain sensor, the
switch must be moved up.
T he higher the sensit iv ity se tt ing , the sooner
the windshie ld wipers react to moist ure on
the windshie ld . I nc reased sensitivity is sig­
naled by the windshie ld wipers making a sin­
gle pass over the windshield.
T he rain sensor w iper intervals depend on the
sensitivity setting as well as vehicle speed.
D uring brief stops, wiper motio n will adj ust in
relat ion to the amount o f rain on the w ind­
shield .
A WARNING
-W iper blades are crucial for safe driving!
O nl y when they are i n good co ndit io n are
they able to clear the windows prope rly
to p rov ide uncompromised vis ib ility.
Wo rn o r damaged wipe r blades are a
safety hazard ~
page 67, Replacing
windshield wiper blades!
- T he rain sen so r is only designed to assist
a nd suppor t the driver.
It rem ains enti re­
ly the d river 's responsibility to monitor
outside weathe r conditions and to man­
ually activate the wipe rs as soon as rain
or driz zle reduces visibility through the
windshie ld.
(D Note
In freezing or near freezing conditions:
- Always check that the w iper b lades are
not frozen to the g lass before you turn
the wipe rs on . Loosen a wiper blade
wh ich is frozen in place before operating
the wipers to prevent damage to the
w iper blade or the wiper motor.
- Do not use the w ipers to clear a frosted
w indow. Us ing the wipers as a conven­
ient ice scrape r will destroy the wiper
blades .

-Prior to using a car wash, the windshield
wiper system must be switched
off (lever
in position 0). This helps to prevent unin­
tentional switching on and damage to
the windshield wiper system .
@ Tips
-The windshield wipers are switched off
when the ignition is turned off. Activate
the windshield wipers after the ignition is switched back on by moving the wind­
shield wiper lever to any position.
- Worn or dirty windshield wiper blades
cause smearing which can affect the op­
eration of the rain sensor. Check the con­
dition of your windshield wiper blades
regularly.
- The rain sensor is part of the interval
wiping system. Turning
off the ignition
will also deactivate the rain sensor. To re­
activate the sensor, switch
off the inter­
val wiping function, then switch it back
on again.
- Make sure the washer fluid reservoir in
the engine compartment is topped
off
before going on a long trip. Look up
c:;, page 272 for checking and filling the
washer container.
Rear window wiper
The wiper lever is also used to operate the
rear window wiper and the automatic wiper/
washer function.
Fig. 66 Wiper lever: activati ng th e rear window w iper
and washer
The rear window wiper and the automatic wip­
er/washer functions are activated as follows:
Clear vision 65
Intermittent wiping
.,. Push the wiper lever forward to the first po­
sition @
c:;, fig. 66. The rear window wiper
will wipe the window approx. every four sec­
onds.
Automatic wiper/washer function
.,. Push the wiper lever forward to the second
stop,
position (J) , and hold it there for as
long as you want the rear wiper/washer to
operate.
.,. Release the lever again . the wiper will keep
running for approx. four seconds.
Switching intermittent wiper action off
.,. Pull the lever all the way back to the original
position.
As soon as the reverse gear is engaged and
the front wipers are turned on and operating
at the same time, the rear wiper also turns on
automatically.
A WARNING
Wiper blades are crucial for safe driving!
Only in good condition are they able to
clear the windows properly to provide un­ restricted visibility. Worn or frayed wiper
blades are a safety hazard!
c:;, page 67,
Replacing windshield wiper blades
(D Note
In freezing or near freezing conditions:
- Always check that the wiper blades are
not frozen to the glass before you turn
the wiper on. Loosen a wiper blade which
is frozen in place before operating the
wiper to prevent damage to the wiper
blade or the wiper motor.
- Do not use the wiper to clear a frosted
window . Using the wipers as a conven­
ient ice scraper will destroy the wiper
blades.
-

66 Clear vis ion
Headlight washer system
Ap plies to vehicles: with hea dlig ht washer syste m
The headlight washer system cleans the
headlights .
.. Operate the windshield wiper/washer sys­
tem
q page 63, fig. 65 ® with the head­
lights turned on by holding the lever for lon ­
ger than one second .
The washer jets extend forward out of the
front bumper driven by water pressure to
spray the front headlights with water .
You shou ld inspect the headlights regularly
(for example when refueling) and clean off
any solid dirt or insects from the lenses .
To ensure the system works proper ly in winter,
keep the washer jets free of snow and remove
any ice using a de- ic ing spray.
Service position
The wiper blades can only be changed in the
service position.
.. If the wiper blades are not frozen to the
windshield, bring the windshield wiper lever
to the basic position@¢
page 63 , fig. 65 .
.. Se lect :
I CAR I function button> S ystems *
control button> Windshi eld w ip e rs > S er v­
ice positi on.
Or
.. Se lect :
I CAR ! funct io n button > Car sy stems *
control button > Servicing & checks > Wiper
servic e po sition .
-On -chang ing the windshield w iper b lades
can on ly be done if you bring the wiper a rms
to the se rv ice posi tion. You w ill also avoid
paint damage to t he hood when working on
the wipers in this pos ition.
- Off -the wi ndshield wipe rs a re moved to
their initial pos ition aga in.
(D Note
N ever maneuve r your vehicle with the
front windshield wipe r arms ra ised si nce
they wi ll a utomat ica lly be moved back to the
ir basic position above a speed of 3
mph
(6 km/h) and ca n scratch the hood.
(D Tips
- Yo u can also use the se rv ice posi tion, for
examp le, i f you want to p rotec t the
windshield from icing by using a cover .
- T he service posit ion automatically
switches to
Off when you operate the
w indshield wiper lever, or speed exceeds
3 mph (6 km/h).
Cleaning windshield wiper blades
Clean the windshie ld w iper b lades when they
begin to leave st reaks .
.. Place the windsh ie ld w iper arms in the serv­
ice pos it ion. Refer to ¢
page 66.
.. Lift the wiper arm away from the rear win­
dow .
.. Use a soft cloth and glass cleane r to clean
the wi ndshield wipe r blades.
.&_ WARNING
Dir ty windsh ield wipe r blades can impair
your view. This can lead to accidents.
.

Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear .
®
Fig. 67 Remov ing t he w iper b lades
F ig . 68 Insta lling w iper blades
Removing a wiper blade
.. Bring the windshield wipers to the service
posit ion ¢
page 66.
.. Lift the w iper arm away from the wind­
shield .
.. Squeeze the plastic bracket on the w ind­
shield wiper a rm together on both sides @
¢fig . 67 .
.. Turn the w iper blade away from the wiper
arm.
.. Lift the w iper blade off in the direc tion of
the a rrow @.
Installing wiper blade
.. Pla ce the new wiper b lade in the retainer on
the wiper arm © ¢
fig. 68 .
.. Swing the wipe r blade in the d irection of the
arrow @ agai nst the wiper arm .
.. Squeeze the corrugation on the wiper until
you hear the b racket click in the w iper arm .
.. Place the wiper arm back against the wind­
shield .
Clear vi sion 6 7
If the wiper blades begin to streak the wind ­
shield, this cou ld be caused by residue left on
the windshie ld by automatic car washes .
Fill the w indshield washe r containe r with a
special solution avai lab le at your authorized
Audi dealer to remove the resid ue.
A WARNING
For your safety, you shou ld rep lace the
wiper b lades once or twice a year. See your
authorized Audi dealer for replacement b lades.
(D Note
- The windshie ld w iper blades must only
be replaced when in the service pos ition
¢
page 66! Otherw ise, you risk damag­
ing the paint on the hood or the wind­
shield wiper mo to r.
- To help p revent damage to the w iper sys­
tem, always loosen blades wh ic h are fro­
zen to the windshield before operating
w ipers.
- T o help p revent damage to wiper blades ,
do not use gaso line, kerosene, paint
t hinne r, or ot her so lven ts on o r near the
w iper blades .
- T o help p revent da mage to the w iper
arms or o ther comp onents, do not at­
t empt to move t he wipe rs by h and.
© Tips
Commerc ial hot waxes applie d by auto­
m atic car washes affe ct the clea na bility of
the w indshield.

68 Clear vision
Changing the rear wiper blade
Fig. 69 Rear w indow wiper Detac hing the rear wipe r
bl ade
Removing the wiper blade
.,. Fold the w indshield wiper arm away from
the glass .
.,. Grasp the upper end of the wiper arm with
one hand and the metal clamp on the wipe r
blade with the other
¢fig. 69 .
.,. Hold the wiper arm in the direction of the
arrow @and pull the w iper blade out of the
holder only in the direction of the arrow @.
Attaching the wiper blade
.,. Adjust the w iper blade in the holder.
.,. Hold the upper end of the wiper arm with
one hand .
.,. Press the w iper blade into the holder with
your other hand.
.,. Fold the wiper arm back onto the wind­
shield .
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice a
year.
-
Mirrors
Adjusting the exterior mirrors
Fig. 70 Forward sectio n of drive r's armrest: powe r mir­
ror controls
Adjusting exterior mirrors
.,. Rotate the knob to the © position (driver's
exte rior m irror) or to the@ position (pas­
senger's exterior m irror)
9 fig. 70 .
.,. Rotate the knob and the mirror so that you
have a clear view to the rear.
Heated mirrors
.,. Rotate the knob to position@ .
Folding both exterior mirrors flat*
.,. Rotate the knob to position @.
Depending on the outside temperature, the
mirror surfaces are heated until the ignit ion is
switched off -even if the knob is no longer in
pos ition @.
You are we ll-advised to fo ld the exter ior mir­
rors in when maneuver ing in tight spaces or
when leaving the car parked close to other
vehicles.
Memory setting for the exterior mirrors*
When the seat position is saved in the memo­
ry, the position of the exterior mirrors is saved
at the same time
9 poge 74.
If the position of the passenger m irror is
changed when the vehicle is in reverse gear
and the switch is in the ® position, this new
ti lted position wi ll be automatically saved to
the remote key when the vehicle is taken out
of reverse gear. To save, the rotary knob for
mirror adjustment must be in the ® position, ...,

the selector lever must be in the P position
and the ignition must be off. This will now be­
come the stored setting when the vehicle is
put in reverse gear again.
Tilting th e pa sseng er's si de exte ri or
m irror (only with se at mem ory )
When you move the selector lever into R (Re­
verse), the mirror on the front passenger's door (knob turned to ®
c::> fig. 70) will tilt
slightly downward. This make is easier for you
to see the curb when you are backing into a
parking space .
The mirror returns to its initial position as soon as reverse gear is disengaged and vehicle
speed is above about
9 mph (15 km/h). The
mirror a lso returns to its in itia l posit ion if the
sw itch is moved to the drive r's exte rior mi rror
© o r the ignit ion is switched off.
0 Note
- Curved (i.e . convex) mirror surfaces in­
crease your field of view. Remembe r th at
vehicles or o ther objects w ill appear
smaller and farther away than when
seen in a flat mirro r. If yo u use this mir ­
ror to est imate distances of following
vehicles when changing lanes, you could
estimate incorrect ly and cause an acci­
dent.
- If the mirror hous ing is moved un inten­
tionally (for example, while park ing your
vehicle), then you must first fo ld the mir­
ro r electrically . Do not readjust the mir­
ror hous ing manually. You could damage
the motor which controls the mi rror.
- If you wash t he veh icle in an automatic
car wash, you must fold the exte rior m ir­
r o rs in to redu ce the r is k of damage to
the mirrors. Never fold power folding ex­
te rior mi rrors* by hand . Only fold them
in and out using the power cont ro ls.
(D Tips
If there should be a malfunc tion in the
elec trical system, you can still ad just the
exterior m irrors by pressing the edge o f
the mirror.
Clear vis ion 69
Dimming the mirrors
0 ~
-.:,
~
Fig. 71 Auto mat ic d immin g rea rv iew m ir ror *
Manu al a nti-gl are adju stment
... Move the small lever ( located on the bottom
edge of the mirror) to the rear .
Automatically dimming mirro rs*
... To dim the rearview mirror and both exterior
m irrors*, press the @button . T he diode @
turns on. The rearview and exterior mirrors *
dim automatically when light shines on
them, for examp le from headlights on ave­
hicle to the rear.
A WARNING
-Electro lyte fluid can leak from automatic
d imm ing mirro rs if the glass is broken.
E lect ro lyte fluid can irritate skin, eyes and
respira to ry system.
- Repeated or prolonged exposu re to e lec­
trolyte can cause irritation to the respira ­
t ory sys tem, especially among people
with asthma or o ther resp iratory condi­
tions . Get fresh air immediately by leav ­
ing the vehicle or, if that is not possib le,
open w indows and doors a ll the way.
- If electrolyte gets into the eyes, flush
them thorough ly with large amounts of
clean water for at least
15 minutes;
medical attention is recommended.
- If electrolyte contacts skin, flush affect ­
ed area with clean water for at least 15 minutes and then wash affected area
with soap and water; medical attention is recommended. Thoroughly wash af­
fected clothing and shoes before reuse.

70 Clear vision
-If swallowed and person is conscious,
rinse mouth with water for at least 15
minutes. Do not induce vomiting unless
instructed to do so by medical professio­
nal. Get medical attention immediately.
d) Note
Liquid electrolyte leaking from broken mir­
ror glass will damage any plastic surfaces
it comes in contact with. Clean up spilled
electrolyte immediately with clean water
and a sponge.
@ Tips
- Switching off the dimming function of
the inside rear view mirror also deacti­
vates the automatic dimming function of
the exterior mirrors*.
- The automatic dimming mirrors do not
dim when the interior lighting is turned
on or the reverse gear is selected.
-Automatic dimming for the mirror only
operates properly if the sun shade* for
the rear window is not in use or the light
striking the inside mirror is not hindered
by other objects .
Digital compass
Activating or deactivating the compass
Applies to vehicles: with d ig ital compass
The direction is displayed on the interior rear
view mirror.
Fig. 72 I n side rear vi ew mirr or: digital compass acti·
vate d
~ To activate or deactivate, hold the@button
down until the red display appears or disap­
pears. The
digital compass only works with the igni­
tion turned on. The directions are displayed as
initials:
N (North), NE (Northeast), E (East),
SE (Southeast), S (South), SW (Southwest),
W (West), NW (Northwest).
(0 Tips
To avoid inaccurate directions, do not al­
low any remote controls, electrical sys­
tems, or metal parts close to the mirror.
Setting the magnetic deflection zone
Applies to vehicles: wit h digital compass
The correct magnetic deflection zone must be
set in order to display the directions correctly.
Fig. 73 North America: magnetic deflection zone
boundar ies
., Hold the@~ page 70, fig. 72 button down
until the number of the set magnetic deflec­
tion zone appears on the interior rear view mirror.
., Adjust the magnetic deflection zone by re­
peatedly pressing on the @button. The set
mode automatically deactivates after a few
seconds.