2014 AUDI Q7 Owner´s Manual

plate. If this hap pens , the vehicle may
start to m ove whi le a whee l is being
changed.
- Never use the folding chocks if they are
damaged or i f they have not been assem­
bled correct ly.
A WARNING
Improper use of the vehicle jack can cause
ser ious personal injuries.
- Never use the jack supplied with your
Audi on another vehicle, particularly on a heavier one. The jack is only suitable for
use on the vehicle it came w ith .
- Us ing a bumper jack to raise the vehicle
will damage the bumper system. The
jack may slip, causing i njury.
- Never support your vehicle on cinder bloc ks, b ricks or other objects. Th ese
may not be able to support the load and
cou ld cause injury when they fail.
- Never start or run t he engine while the
vehicle is suppor ted by the jack.
- If you must wo rk under the vehicle, al­
ways use safety stand s spe cifically de­
signed for this purpose.
- Always make sure the inflatable spare
tir e a nd even a f lat t ire are se cured in
place and not loose, ot herwise they
cou ld fly forward, causing personal inj ury
to passengers in the veh icle in an acc i­
dent or sudden mane uver.
Removing bass box
Applies to vehicles: with bass box
Before the inflatable spare tire can be taken
out, the bass box must be removed .
Fig . 2 58 Spare wheel well: Sass box
What do I do now ? 295
Removing bass box
.,. Squee ze the locking tabs ~ fig . 258 (D of
the conne ctor .
.,. Disconnect the connector @and place the
lead to one side.
.,. Turn the large screw counter-clockwise .
.,. Carefully remove the bass box.
Installing bass bo x
.,. Carefully p lace the bass box in the wheel.
The inscription "F RO NT" on the bass box
must face forward .
.,. Reconnect the connector that was removed.
.,. Secure the bass box with the large screw .
Inflatable spare tire
The inflatable spare tire expands to its full di­
ameter when it is inflated.
Fig. 25 9 In flatable spare tir e w ith compressor
Removing inflatable spare tire
.,. Lift up the cargo floo r us ing the handle .
"' Turn the large screw
9 fig . 259 co unte r-
clockw ise.
"' Remove the bass box as required
¢ page 295 .
.,. Take out the in flatable spare tire .
.,. Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
9 page 170.
Stowing the inflatable spare t ire
"' Release the ai r by u nscrewing the valve
stem .
.,. Screw the valve stem back in afterwards .
.,. Wait a few hours before p lac ing the wheel in
the spare wheel we ll¢ ,& .
"' Install the bass box as required ¢
page 295 . ..,_

2 9 6 What do I do no w?
• Secure the wheel with the large screw.
• Fold the cargo floor back down .
After using th e inflat able spare wheel
The inflatable spare t ire can be re-used as
l ong as it is not damaged and is not worn
down to the tread wear indicators
c::> A .
When you let the air out of the inflatable
spa re tire, it does not assume its folded shape
again for several ho urs. Until then, it cannot
be p laced back in the spare wheel well and
stowed securely.
A WARNING
- Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators.
- If the inflatable spare tire is more than 6
years old, use it on ly in an emergency
and with extreme caut ion and careful
driv ing .
- The inflatable spare tire is intended only
for temporary and short-term use .
It
should be replaced as soon as possible
with the no rmal wheel and tire .
- The tire pressure value for the inflatable
spare t ire is located on the driver's side
B-p illar
c::> page 277, fig . 250.
-Maximum perm iss ible speed is SO mph
(80 km/h).
- Avoid full-throttle acce lerat ion, heavy
braking, and fast corner ing .
- When the air is let out of the inflatable
spare wheel, it does not assume its fold­
ed shape for several hours . Until then, it
cannot be placed back in the spare wheel
we ll and stowed secu rely.
- Never drive with more than one inflata­
ble spare ti re.
- For technical reasons, the use of tire
chains on the inf latable spare tire is not
permitted.
If i t is necessary to drive w ith
t ir e cha ins, the infla table spare wheel
must be mounted on the front axle in the
event of a flat in a rear tire . The newly
available front whee l must the n be in­
sta lled in place of the rear wheel with the flat tire
. Insta lling the ti re cha in be­
fore mounting the wheel and tire is rec­
ommended.
- Loose items in the passenger compart­
ment can cause serious personal injury
during hard brak ing or in an accident.
Never store the inflatable spare tire or
jack and tools in the passenge r compart­
ment.
(D Note
- The inflatable spare tire has been deve l­
oped specifically for th is veh icle model.
It must not be exchanged or used for
other vehicle models. Sim ila rly, inflata­
ble t ires from other vehicle models m ust
no t be used.
- Norma l summer or w inte r ti res must not
be ins talled on the infla table t ire rim.
Inflating inflatable spare tire
• Remove the compressor from the luggage
compartment
c::> page 295 , fig. 259.
• Unscrew the valve stem from the spare tire.
• Screw the tire f iller hose from the compres­
sor firmly onto the
valve of the spare tire.
• Insert the plug from the compressor into an
outlet of the ve hicle
c::> page 88 .
• Switch the comp ressor on .
• Let the compressor run unti l the va lue speci­
fied on the ti re p ressu re label is reached
c::> page 2 77, fig. 250 . Switc h the compres­
sor off after running for 12 m inutes at the
most -danger of overheating!
A WARNING
-The compressor and the tire f iller hose can
become extremely hot while they are run­
n ing -danger of burns!
([) Note
Switch the compressor off after running
for 12 min utes at the most -danger of
overheating! Allow the compressor to cool
down for a few m inutes before you use it
again .

Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fa ilure, pull the
car well away from moving traffic and try to
reach
level gro und before you stop¢.&_ .
.. All passengers should
leav e the car and
move to a safe location (fo r instan ce, be hind
the guardra il) ¢.&_ .
.,. Engage the
parkin g brake to prevent your
vehicle from ro lling unintentionally ¢.&_ .
.. Move
selecto r le ver to p osition P ¢ .&_ .
1> Ifyou are towing a trai ler: unhitch the trail­
er from your veh icle.
.,. Block the diagonally opposite wheel with
the folding chocks or other objects .
.. Take the
jack and the inflatab le spare tire
out of the luggage compartment
¢ page 294.
& WARNING
You or your passengers cou ld be injured
while changing a whee l if yo u do not fol­
low these safety precautions:
- If you have a flat t ire, move a safe dis ­
tance off the road . Turn off the eng ine,
t ur n the emergency flashers o n and use
other warning devices to alert other mo­
torists .
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To he lp prevent the veh icle from mov ing
sudden ly and possibly slipping off the
jack, always fully set the parking b rake
and block the whee l diagonally opposite
the wheel being cha nged with the fo ld­
ing chocks or othe r objects. When one
front whee l is lifted off the g ro und, plac­
ing the A utomat ic Transm iss ion in P
(Park) wi ll
not prevent the vehicle from
moving .
-
What do I do now? 297
-Before you change a whee l, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
<=:>page 170 .
Changing a wheel
When you change a wheel , follow these­
quence described below step-by-step and in
exactly that order.
1. Activate the vehicle jack mode (only
vehicles with Adaptive Air S uspension)
¢ page 159 .
2. Remove the decorati ve wheel co ver* . For
more details see also <=:>
page 298, Deco­
rative wheel covers
or <=:> page 298,
Wheels with wheel bolt caps .
3. Loosen the wheel bolt s¢ page 298 .
4. Loca te the p roper mounting point for the
jack and align the jack be low that point
¢ page 299.
5. Lift the car with the jack Q page 299 .
6. Remove the wheel with the flat ti re and
then install the
inflatable spare tire
¢ page 300.
7. Tig hte n all wheel bolts lightly.
8 .
Lowe r the vehicle with the jack .
9. Use the wheel bolt w rench and
firmly
t ighten all wheel bolts¢ page 298 .
10. Replace the decora tive whe el co ver* .
11. Deactivate the vehicle jack mode (on ly
vehicles with Adaptive Air S uspension)
¢ page 159 .
A WARNING
Always read and follow all WARNINGS and
informat ion<=:>
& in Raising the vehicle on
page 300
and <=:> page 301.
•
•

2 98 What do I do now ?
After changing a wheel
A wheel change is no t complete without do­
ing the following .
"'Always store the vehicle tool kit, the jack
and the replaced ti re i n the luggage com­
partment
¢ page 170.
"'As soon as possible, have the tightening
torques
on a ll wheel bo lts ch ecked with a
tor que wrench. The correct tigh ten ing tor­
que is 120
ft lb (160 N m).
"' Have the flat tire
replaced as soon as poss i­
b le.
@ Tips
- I f yo u notice t hat the wheel bolts are
corroded and difficult to turn w hile
changing a t ire, they should be re p laced
b ef ore yo u check the tighten ing torque.
- Drive at red uced s peed unti l y o u have the
t ig htening torq ues chec ked.
Decorative wheel covers
App lies to vehicles: with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig . 260 C han ging a w hee l: R em ovin g the whee l cove r
Removing
"'Insert the hook provided with the ve hicle
tool kit in the hole in t he hub.
"' Pull off the
decorat ive wheel cover
c:> fig . 260 .
' Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
s crewed .
Fig. 261 Chang ing a w heel: re m ov ing th e w hee l b o lt
caps
Removing
"' Push t he plastic clip provided with the ve hi­
cle tool kit over the w heel bo lt cap until it
engages .
"' Pull on th e
plastic clip to remove t he cap
c:> fig. 261 .
Refitting
"' Place t he caps over the whee l b olts and
push them back o n.
The caps are to protect and keep the wh eel
bolts clean.
Loosening and tightening the wheel
bolts
The wheel bolts mus t be loosened before rais­
ing the v ehicle .
Fig. 26 2 Cha ng ing a w hee l: loosening th e w hee l bo lts II--

Loosening
• Install the wheel bolt wrench over the
whee l bolt and push it down as far as it wi ll
go.
• Take tight hold of th e
end of the wrench
handle and turn the whee l bolts
counter­
clockwise
abou t one single turn in the di rec·
tion of arrow
c::> fig. 262 .
Tightening
• Install the wheel bolt wrench over the
wheel bolt and push it down as far as it will
go .
• Take tight hold of the
end of the wrench
handle and turn each wheel bolt
clockwise
until it is seated .
& WARNING
-Do not use force or hurry when changi ng
a whee l· you can cause the vehicle to slip
off the jac k and cause serious personal
injuries .
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury.
(j) Tips
If a wheel bolt is very tight, you may find it
easie r to loosen by carefully pushing down
on the end of the wheel bolt wrench with
one foot only. As you do so, hold on to the
car to keep yo ur balance and take care not
to slip.
Raising the vehicle
The vehicle must be lifted with th e jack first
before the wheel can be removed .
Fig. 263 Sill pane ls: m arkin gs
What do I do now? 299
Fig. 264 Sill: p ositioning the jack
• Activate the vehicle jack mode* (only
veh icles with Adaptive Air Suspension)
c::> page 159 .
• Engage the parking brake to prevent your
vehicle from rolling unintentionally
• Move the
selector lever to position P .
• Find the marking (imprint) on the sill that is
nea rest the whee l that will be changed
c::>fig. 263. Behind the marking, there is a
lifting point on the sill for the jack.
• Turn the
jack located under the lifting point
on the sill to raise the jack until its arm@
c::> fig. 264 is located under the designated
plastic mount
c::> .&. c::> Q) .
• Align the jack so that its arm@ c::> fig. 264
engages in the designated lifting point in
the door s ill and the movable base® lies
flat on the ground. The base@ must be
ver­
tical
under the lifting point@.
• Wind the jack up further until the flat tire
comes off the ground
c::> .,& .
Position the jack only under the designated
lifting points on the sill
c::> fig. 263. There is
exactly
one locat ion for each whe el. The jack
must not be positioned at any other location
c::> .&. c::> Q).
An unstable surface under the jack ca n cause
the vehicle to slip off the jack. Always provide
a firm base for the jack on the ground . If nec ­
essary place a sturdy board or similar support
under the jack . On
hard, slippery surfaces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping
c::> ,&.. .,,.

300 What do I do now?
& WARNING
-You or your passengers could be injured
while changing a wheel if you do not
follow these safety precautions:
- Position the jack only at the designated
lifting points and align the jack. Other­
wise, the jack could slip and cause an injury if it does not have sufficient hold
on the vehicle.
- A soft or unstable surface under the
jack may cause the vehicle to slip off the jack. Always provide a firm base for
the jack on the ground . If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then continue to
raise the jack.
(D Note
Do not lift the vehicle by the sill. Position
the jack only at the designated lifting
points on the sill. Otherwise , your vehicle
will be damaged.
Taking the wheel off /installing the
inflatable spare tire
Follow these instructions step-by-step for
changing the wheel
Fig. 265 Changing a wheel: alignment pin inside the
top hole
After you have loosened all wheel bolts and raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.,. Remove the topmost wheel bolt completely
and set it aside on a
clean surface.
.,. Screw the threaded end of the
alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig . 265.
.,. Then remove the other wheel bolts as de­
scribed above.
.,. Take off the wheel leaving the alignment pin
in the bolt hole ¢(D.
Putting on the inflatable spare tire
.,. Inflate the inflatable spare tire ¢ page 296
and push the wheel over the alignment pin.
"Screw in and tighten all wheel bolts
slightly.
.,. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly
like the rest .
.,. Turn the jack handle counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
" Use the wheel bolt wrench to tighten all
wheel bolts firmly ¢
page 298 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.

(D Note
When removing or installing the wheel,
the rim could hit the bra ke rotor and dam­
age the rotor . Wor k carefully and have a
second person help you.
- W hen mounting tires with
unidirectional
tread design
ma ke s ure the tread pat­
tern is pointed the r ight way
<=> page 301.
-The wheel bolts should be clea n and easy
to tu rn . Check for d irt and corrosio n on
t h e mat ing su rfaces of both the whee l
and the hub. Remove a ll dirt from these
su rfaces before remo untin g t he wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tr ead pattern point ed in
the right dire ction.
Using a spare tire with a tread pattern
intended for use in a specific direction
W hen using a spa re tire w ith a t read patte rn
in te nded fo r use in a specific direction, p lease
n ot e t he followi ng:
- The direction of rotation is marked by an ar­
row on the side of the tire .
- If the spare t ire has to be installed in the in ­
correct di rection, use the spa re tire only
tem porarily si nce th e tir e will not be able to
a ch ieve i ts op timum pe rfo rm ance chara cter­
is tics with reg ard to aq uaplani ng, noise and
wea r.
- W e recommend that you p ay pa rticular at­
tent io n t o this fact du ring wet weathe r and
t h at you adjus t your spee d to matc h roa d
con dit ions .
- Re place the fla t tire w ith a new one and
have it installed on your vehicle as soon as
poss ible to restore the hand ling advantages
of a unid irect iona l tire.
What do I do now?
Notes on wheel changing
P lease read t he i nfo rmat ion c:> page 284, New
t ires and replacing tires and wheels
if y ou a r e
go ing to use a sp are tire w hich is different
from the ti res on yo ur vehicle.
After yo u cha nge a tire:
- Check the tire pressure on the spare imme­
diately after installation .
- Have the wheel bolt tightening torque
che cked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 120 ft lb (160 Nm) .
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque.
- Repla ce the flat tire with a new one and
have it installed on your vehicle as s oon as
possible. Remount the wheel cover.
Until then, drive with extra care and at re­
duced speeds .
&_ WARNING
-
- If yo u are goi ng to e quip yo u r ve hicl e
wit h tires o r rims whi ch di ffer from those
which were fac to ry installed, t hen be
sure to rea d the information
c:> page 284,
New tires and replacing tires and
wheels.
- Always make s ure the damaged wheel o r
even a flat tire and the jack and t ool kit
are prope rly secured in the luggage com ­
pa rtme nt and are not loose in the pas ­
senge r compartment .
- In an accident or sudden maneuver they
could fly forwa rd, inj uri ng a nyo ne in the
veh icle.
- Always sto re damaged wheel , jack a nd
too ls sec urely in the luggage compa rt ­
men t. Othe rwise, in a n accide nt o r sud­
de n m aneuver they could fly forwa rd,
c a u sing i nju ry to passenger s in th e ve hi­
cle.
301
•
•

302 Fuses and bulbs
Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through.
Fig . 266 Left cockp it: fuse panel cover
•
•
F ig . 267 Right luggage compa rtment: s ide t rim
The fuses are located at the fron t left and
right of the cockpit and behi nd the trim on
the r ight side of the luggage compartmen t.
.,. Turn off the ignit ion and the affected electri­
cal consumers.
ll You ca n dispose of the plastic clip after remov ing it.
.. Check the following tab le to see wh ich fuse
be longs to the consumer.
.. Remove t he appropriate cover .
.. To remove the purp le plastic clip if necessa­
ry
1) , hold onto it at the small side and pull
it out of the fuse pane l
c:> page 303,
fig.
268 .
• Remove the clamp from the rear side of the
fuse cover
c:> fig. 266.
• Remove the f use us ing the clamp and re­
p lace t he bl own f use with an iden tica l new
one.
A WARNING
--
Do not repair fuses and never replace a
b lown fuse with one that has a hig her amp
rat ing. Th is can ca use damage to the elec­
tr ica l system and a fire .
(D Note
If a new fuse burns out again after shortly
have you have installed it, have the e lectri­
ca l system checked by yo ur authorized
Audi dealer .
{!) Tips
-The following table does not list fuse lo­
cat ions that are not used.
- Some of the equipment items listed are
optional or only available on certa in
mode l configurations .