2014 AUDI Q7 rear view mirror

68 Clear vision
Changing the rear wiper blade
Fig. 69 Rear w indow wiper Detac hing the rear wipe r
bl ade
Removing the wiper blade
.,. Fold the w indshield wiper arm away from
the glass .
.,. Grasp the upper end of the wiper arm with
one hand and the metal clamp on the wipe r
blade with the other
¢fig. 69 .
.,. Hold the wiper arm in the direction of the
arrow @and pull the w iper blade out of the
holder only in the direction of the arrow @.
Attaching the wiper blade
.,. Adjust the w iper blade in the holder.
.,. Hold the upper end of the wiper arm with
one hand .
.,. Press the w iper blade into the holder with
your other hand.
.,. Fold the wiper arm back onto the wind­
shield .
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice a
year.
-
Mirrors
Adjusting the exterior mirrors
Fig. 70 Forward sectio n of drive r's armrest: powe r mir­
ror controls
Adjusting exterior mirrors
.,. Rotate the knob to the © position (driver's
exte rior m irror) or to the@ position (pas­
senger's exterior m irror)
9 fig. 70 .
.,. Rotate the knob and the mirror so that you
have a clear view to the rear.
Heated mirrors
.,. Rotate the knob to position@ .
Folding both exterior mirrors flat*
.,. Rotate the knob to position @.
Depending on the outside temperature, the
mirror surfaces are heated until the ignit ion is
switched off -even if the knob is no longer in
pos ition @.
You are we ll-advised to fo ld the exter ior mir­
rors in when maneuver ing in tight spaces or
when leaving the car parked close to other
vehicles.
Memory setting for the exterior mirrors*
When the seat position is saved in the memo­
ry, the position of the exterior mirrors is saved
at the same time
9 poge 74.
If the position of the passenger m irror is
changed when the vehicle is in reverse gear
and the switch is in the ® position, this new
ti lted position wi ll be automatically saved to
the remote key when the vehicle is taken out
of reverse gear. To save, the rotary knob for
mirror adjustment must be in the ® position, ...,

the selector lever must be in the P position
and the ignition must be off. This will now be­
come the stored setting when the vehicle is
put in reverse gear again.
Tilting th e pa sseng er's si de exte ri or
m irror (only with se at mem ory )
When you move the selector lever into R (Re­
verse), the mirror on the front passenger's door (knob turned to ®
c::> fig. 70) will tilt
slightly downward. This make is easier for you
to see the curb when you are backing into a
parking space .
The mirror returns to its initial position as soon as reverse gear is disengaged and vehicle
speed is above about
9 mph (15 km/h). The
mirror a lso returns to its in itia l posit ion if the
sw itch is moved to the drive r's exte rior mi rror
© o r the ignit ion is switched off.
0 Note
- Curved (i.e . convex) mirror surfaces in­
crease your field of view. Remembe r th at
vehicles or o ther objects w ill appear
smaller and farther away than when
seen in a flat mirro r. If yo u use this mir ­
ror to est imate distances of following
vehicles when changing lanes, you could
estimate incorrect ly and cause an acci­
dent.
- If the mirror hous ing is moved un inten­
tionally (for example, while park ing your
vehicle), then you must first fo ld the mir­
ro r electrically . Do not readjust the mir­
ror hous ing manually. You could damage
the motor which controls the mi rror.
- If you wash t he veh icle in an automatic
car wash, you must fold the exte rior m ir­
r o rs in to redu ce the r is k of damage to
the mirrors. Never fold power folding ex­
te rior mi rrors* by hand . Only fold them
in and out using the power cont ro ls.
(D Tips
If there should be a malfunc tion in the
elec trical system, you can still ad just the
exterior m irrors by pressing the edge o f
the mirror.
Clear vis ion 69
Dimming the mirrors
0 ~
-.:,
~
Fig. 71 Auto mat ic d immin g rea rv iew m ir ror *
Manu al a nti-gl are adju stment
... Move the small lever ( located on the bottom
edge of the mirror) to the rear .
Automatically dimming mirro rs*
... To dim the rearview mirror and both exterior
m irrors*, press the @button . T he diode @
turns on. The rearview and exterior mirrors *
dim automatically when light shines on
them, for examp le from headlights on ave­
hicle to the rear.
A WARNING
-Electro lyte fluid can leak from automatic
d imm ing mirro rs if the glass is broken.
E lect ro lyte fluid can irritate skin, eyes and
respira to ry system.
- Repeated or prolonged exposu re to e lec­
trolyte can cause irritation to the respira ­
t ory sys tem, especially among people
with asthma or o ther resp iratory condi­
tions . Get fresh air immediately by leav ­
ing the vehicle or, if that is not possib le,
open w indows and doors a ll the way.
- If electrolyte gets into the eyes, flush
them thorough ly with large amounts of
clean water for at least
15 minutes;
medical attention is recommended.
- If electrolyte contacts skin, flush affect ­
ed area with clean water for at least 15 minutes and then wash affected area
with soap and water; medical attention is recommended. Thoroughly wash af­
fected clothing and shoes before reuse.

70 Clear vision
-If swallowed and person is conscious,
rinse mouth with water for at least 15
minutes. Do not induce vomiting unless
instructed to do so by medical professio­
nal. Get medical attention immediately.
d) Note
Liquid electrolyte leaking from broken mir­
ror glass will damage any plastic surfaces
it comes in contact with. Clean up spilled
electrolyte immediately with clean water
and a sponge.
@ Tips
- Switching off the dimming function of
the inside rear view mirror also deacti­
vates the automatic dimming function of
the exterior mirrors*.
- The automatic dimming mirrors do not
dim when the interior lighting is turned
on or the reverse gear is selected.
-Automatic dimming for the mirror only
operates properly if the sun shade* for
the rear window is not in use or the light
striking the inside mirror is not hindered
by other objects .
Digital compass
Activating or deactivating the compass
Applies to vehicles: with d ig ital compass
The direction is displayed on the interior rear
view mirror.
Fig. 72 I n side rear vi ew mirr or: digital compass acti·
vate d
~ To activate or deactivate, hold the@button
down until the red display appears or disap­
pears. The
digital compass only works with the igni­
tion turned on. The directions are displayed as
initials:
N (North), NE (Northeast), E (East),
SE (Southeast), S (South), SW (Southwest),
W (West), NW (Northwest).
(0 Tips
To avoid inaccurate directions, do not al­
low any remote controls, electrical sys­
tems, or metal parts close to the mirror.
Setting the magnetic deflection zone
Applies to vehicles: wit h digital compass
The correct magnetic deflection zone must be
set in order to display the directions correctly.
Fig. 73 North America: magnetic deflection zone
boundar ies
., Hold the@~ page 70, fig. 72 button down
until the number of the set magnetic deflec­
tion zone appears on the interior rear view mirror.
., Adjust the magnetic deflection zone by re­
peatedly pressing on the @button. The set
mode automatically deactivates after a few
seconds.

Calibrating the compass
Appl ies to vehicles: with digital compass
The compass has to be recalibrated if the dis­
play is wrong or inaccurate .
.. Hold the@ button down until the letter C is
displayed on the interior rear view mirror .
.,. Drive in a c ircle at a speed of about 5 mph
(10 km/h) until a d irection is s hown on the
interior rea r view m irror .
A WARNING
The d igital compass is to be used as a di­
rec tional a id only. Even though you may
want to look at it while you are driv ing, you
must still pay attention to t raffic, road and
weather condit ions as we ll as other possi­
ble hazards.
Clear vis ion 71

Audi side assist Lane Change Assistant
Description
App lies to vehicles: with side assist
The side assist helps you when changing
lanes .
AUDl Q7
Fig. 147 Rear b umper: Pos it ion of radar sensors (not
v isib le on outside)
Fig . 148 Signal light on the outside mirror -driver 's
s ide
~ -..:, .. (D
Side assist uses radar sensors (not visib le on
outside) ¢
fig. 147 to help the driver check
b lind spots, and see what is happen ing in traf ­
fic beh ind the veh icle
¢ page 130, fig. 150.
Signal lights are bu ilt into both outside m ir­
r ors ¢
fig. 148. The signal light on the left
outside mirror assists when moving over into
the left lane and the signal light on the r igh t
ou tside mirror assists when moving over in to
the right lane .
The s ignal light comes on to tell you that side
assis t has detec ted a vehicle on tha t side and
that t he position of this othe r vehicle should
be taken into account if yo u were to change
lanes . This is called the
informatio nal st age
sign al¢
page 131. The informat ional stage
Aud i side assist 129
signal is designed so that you notice it on ly
when you are looking in the outside mirror.
When yo u activate the turn signal and side as ­
s ist de tects a vehicle in a no table location, the
corresponding signal on the outside mi rror
flashes briefly and brightly several times. This
is the
a lert stage signal ¢ page 131 .
Activating and deactivating
Applies to vehicles: wit h side assist
Fi g. 14 9 Drive r's doo r: Side assist button
Activating
.,. Press the ¢ fig. 149 button. The indicator on
t he button lights up .
Deactivating
.,. Press the button again. The indicator light
on the button goes out .
The system works at speeds faster than
19 mph (30 km/h) .
A WARNING
-Imp roper reliance on the side assist sys­
tem can cause coll is ions and serio us pe r­
sonal injury:
- Never rely on ly on side assist when
changing lanes.
- Always check rear view mirrors to make
su re that it is safe to change lanes.
- Side assist canno t detect all veh icles un­
de r all conditions- danger of accident!
- Side assist cannot detect vehicles in time
to a lert you w hen they app roac h from
behind at very hig h speed, or fall drop
back very qu ickly.
~

next to the lane you are using
¢page 135.
Operation
Applies to vehicles: with side assist
Side assist compares the distance and differ­
ence in speed of detected vehicles with the
speed of your vehicle . Whenever the differ­
ence in speed and d istance is registered as no­
table if you were to change lanes, a signal l ight appea rs on the respective mirror.
The signal can light up if you are passed by a
vehicle or if you are pass ing another vehicle.
If you pass another vehicle s lowly (difference
in speed less than 9 mph, or 15 km/h), the
signal light will come on as soon as the other
vehicle is in your blind spot and is detected by
side assist . When the difference in speed is
g reater, the signal light will not come on.
Informational and alert stage signals
Applies to vehicles: with side assist
Side assist has two signal stages:
- the informational stage signal, and
- the alert stage signal.
Side assist he lps you by using the appropriate
signal stage, depending on whether or not
you have activated the turn signal, and thus have indicated that you are or are not chang­
in g lanes .
Informational stage signal
As long as you have not activated the turn sig­
nal, side assist informs you of detected
vehicles that are registered as being in a nota­
b le location if you were to change lanes.
Whenever the detected vehicle's difference in speed and distance is registered by side assist
as notable, the signal light on the respective
mirror produces muted illuminat ion.
The br ightness of the informat ional stage sig ­
nal is designed not to be as intense, so that it
does not interfere with your view of the road
when yo u are driving and have no intention of
changing lanes. When you look i n the outside
Aud i side assist 131
mirror, you can clearly see the informational
stage signal.
Alert stage signal
When you activate the turn signal, and s ide
ass ist has detected a vehicle in a notable loca­
t ion on that part icular s ide, the signa l light on
this side mirror flashes brightly. The repeated
brief and bright flashing of the alert stage
signal reminds you to carefully check traffic to
the rear in the outside mirror and over your
shoulder, so that you can safely complete the lane change
¢ A in Safety tips on page 136 .
@ Tips
The brightness of the signal light on the
outside mirrors can be adjusted with the
MMI ¢page 134.
Driving situation: Fast approaching
vehicles
Applies to vehicles: with side assist
Fig. 151 Side assist : Fast app roaching vehicles
@ Signal on outside mirror does not light
up
No vehicle was detected by the sensors. The
signal on the outside mirror does not light up
¢ A in Safety tips on page 136. IJJ,,

136 Audi side a ssis t
Safety tips
App lies to vehicles: wit h side ass ist
The s ide ass ist detect ion may be lim ited when
d riving around narrow street corners , on hilly
streets, and under poor weathe r cond itions.
It is poss ible that the radar sensors may also
detect other objects , such as high or stag­
gered guardra ils .
Side assist does not measure actual lane
width . The system assumes a fixed lane w idth .
Detection in the left and r ight lanes is based
on this assumed lane width . When driving on
na rrow roads or when driving to the left or
right of the center of a travel lane , it is possi ­
b le that vehicles will be detected that are
not
in the lane next to the lane you are using.
A WARNING
- Improper reliance on the s ide assist sys­
tem can cause collisions and serious per­
sonal injury :
- Never rely only on side assist when
changing lanes .
- Always check rear view mirrors to make
sure that it is safe to change lanes.
- Side ass ist cannot detect a ll vehicles un­
der all cond itions- danger of accident!
- Side ass ist cannot detect vehicles in time
to alert you when they approach from beh ind at very h igh speeds or drop back
very quick ly .
- T he radar sensor's
vision can be reduced
or entirely blocked by rain, snow, and
heavy spray. This can result in side assist
not adequately detecting vehicles or, in
some cases, not detecting them at a ll.
Always keep an eye on the direction you are traveling and the relevant area
around the vehicle .
- Please note that side assist indicates
there are approaching vehicles, or
vehicles in your blind spot, only after
your vehicle has reached a driving speed
of at least 19 mph (30 km/h). -
Side assist signa l does not work around
tight corners (turning radius less than
328 feet, or 100 m).
- Side assist is no replacement for the driv­
er 's full attention. The driver alone is re­
sponsible for lane changes and sim ilar
driving maneuvers. Always keep an eye
on the d irect ion you are traveling and the
re levant area around the vehicle.
(D Note
To ensure that side assist is not adversely
affected, you should not block the area on
the rear bumper where the radar sensors
are located with foreign objects (such as
with stickers or bi cycle racks).
(D Tips
If the pos itions of the radar sensors have
been changed as a result of a rear end-co l­
lision, for instance, have s ide assist
checked by an autho rized Aud i dealer for
safety reasons.

146 Parking sy stems
- The came ra lens en larges and distorts
the field of vision. The object appears
both altered and inaccurate on the
screen.
- In certa in s ituations, people or objects in
the display appear closer or further
away:
- objects th at do no t touch the gro und,
such as the bumper o f a parked vehicle,
a trailer hitch o r the rea r of a truck. Do
not use the help lines in this case.
- If driven from a leve l su rface onto an
incline, or a downward slope .
- I f driven toward protr uding objec ts.
- I f the veh icle is ca rrying too much load
in t he rear.
(D Note
-Always read and fo llow the applicab le
warnings
¢ (D in General information on
page 143 .
-The o range colored orientation lines in
t h e M MI disp lay show t he ve hicl e path
depend ing o n the steering wheel angle .
The front of the vehicle fron t swings out
more than the rea r of the vehicle. Main ­
ta in p lenty of distance so that your o ut­
s ide mirror or a corner of your veh icle
does not collide with any obstacles.
Switching on and off
Applies to vehicles: with Audi parking system p lus w ith
rearview camera
F ig . 167 Center co nsole: P"A button
F ig . 1 68 MMI display: Visual distance display
Switching on
.. Switch the MMI on .
.. Shift into reverse, or
.. Press the
l" •I button in the center console
c:;, fig. 167 . A short confirmation tone
sounds and the LED in the button lights up .
Switching between the rearv iew camera
and visual display
.. Press the Graphic control button
c:;, page 147, fig. 169 ® to see the vis ual
disp lay.
.. Press the
Rear vi ew control b utton to see
t he rearview c amera image
c:;, fig. 168 .
Switching off
.. Dr ive faster than 6 mph (10 km/h) , or
.. Press the~ button, or
.. Switch off the ignition .
Visual displ ay
The red segments in front of and behind the
vehicle
c> fig. 168 help you to determ ine the
distance between you and an obstacle . As
your vehicle comes closer to the obstacle , the
segments move closer to t he veh icle. The col­
lis ion are a has been rea ched when the next to
last segment is displayed . Do no t con tinue
driving farther forward or in reverse
c:;, .&. in
General information on page 143, c:;,@ in
General information on page 143.
(D Tips
-The visua l display in the left part of the
disp lay sho uld he lp you detect t he crit i­
cal ve hicle areas .