2014 AUDI Q7 fold seats

76 Seats and storage
Adjusting seat (second row seating)
The fore-and-aft adjustment* of the seat
cushion and the seatback angle can be ad­
justed .
Fig. 76 Adjust ing seatback angle
Fig. 77 Fore -and -aft ad justment
Adjusting seatback angle
.. Pul l the lever up and push the seatback to­
war d the rear to the desi red position
¢
fig. 76. Release the leve r.
.. Pull the lever up so tha t the seatback pivots
forward . Release the lever and p ush the
seatback to the rear to return the seatback
to the norma l position.
For e-and-aft adju stment*
.. Pull the hand le up and push the seat for­
ward or back¢
fig. 77 .
.. Re lease the hand le and continue to push the
seat until the seat latch engages.
A WARNING
- For safety reasons, the seat must only be
adjusted when the vehicle is stationary -
danger of accident!
- Exercise caut ion when adjusting the seat.
Adjusting the seat w ithout checki ng or paying attention can p
inch fingers or
limbs -danger of in jury!
Entry assist (second row seating)
Applies to vehicles: wit h entry assist
The entry assist makes it easier far occupants
to reach the third row seating* .
Fig. 78 Seatback second row seat ing: Seatback latch
Pushing second row o f se ats forward
.. Lift the lever ¢ fig. 78 .
.. Tilt the seatback forward .
.. Push the seat forward .
Pushing second row o f se ats back
.. Push the seatback.
.. Fold the seatback up unti l it latches .
T o make entry to and exit from the rear of the
vehicle easier, the seatbacks fo r the second
row seating can be folded forward. At the
same t ime, the seats can be pushed forward
and to the rear.

Folding seatback up and down (third
row seating)
Applies to vehicles: with third row seatin g
The third row seating is suitable for persons
up to 1.6 meters (5 ft 3 in) in height .
Fig. 79 Third row o f seats : Fo ld ing seatback up
Fig. 80 Third row o f seats: Fo ld in g seatback dow n
Raising seatback
~ Lift the lever -Arrow- ¢ fig. 79 and raise the
seatback until it locks.
~ Raise the head restraint until it locks.
Folding seatback down
~ Lift the lever -Arrow- ¢ fig. 80 and fold the
seatback down complete ly until it locks.
~ The head restraint is automat ically t ipped
down.
A WARNING
- Only persons up to a height of 5 feet 3
inches (1.6 m) may be carried on the
seats in the third row.
- Exercise caution when folding the seat­
backs up and down. Inattentiveness or
carelessness when folding the seatback
up and down can pinch fingers or hands.
-
Seats and storage 77
-Always check whether the latch is fully
engaged by pull ing the seatback for­
ward.
Head restraints
Front head restraints
Fig. 81 Fro nt seats head rest ra in ts: adjust ing the
height
The head restraints on the front seats can be
adjusted to provide safe support to head and
neck at the optimum height. When optimally
adjusted, the top of the restraint should be level with the top of the head . If that is not
possible, try to adjust the head restraint so
that it is as close to this position as possible
¢ page 167 , Proper adjustment of head re­
straints .
~ To move the head restraint up, hold it at the
sides with both hands and slide it upward.
~ To move the head restraint down, press the
button and slide the head restraint down­
ward ¢
fig. 81.
Refer to¢ page 167, Proper adjustment of
head restraints
for guidelines on how to ad­
just the height of the front head restraints to
su it the occupant's body size.
A WARNING
- Driving without head restraints or with
head restraints that are not properly ad­
justed increases the risk of serious or fa­
tal neck injury dramatica lly.
- Read and heed all WARNINGS
c::>page 167.

78 Seats and storage
@ Tips
Correctly adjusted head restraints and
safety belts are an extremely effective
combinat ion of safety features.
Rear head restraints
F ig. 82 Rear seat: ou ter hea d rest raint
Fi g. 83 Rear se at: ce nte r h ead restra int
I f the re are passengers in the rear seat, fold
the head restraints up on the occupied seats
or slide the cente r head restraint upward at
least to the next notch
~ .,& .
Adjusting the outer head restraints
.,. To fold the head restraint out, pull on the
tab ¢
fig. 82 .
.. To fo ld the head rest raint up, ti lt it upward
until you feel it c lick into p lace.
Adjusting the center h ead restraint
.,. To move the head restra int up , hold it at the
s ides wi th both hands and slide it upwa rd
u ntil you feel it cl ick into p lace
"* fig . 83 .
.. To move the head restraint down, press the
button -arrow -and slide the head restraint
downward.
Remo ving the center head re straint
.,. Move the head res traint upw ard as f ar as i t
can go.
.. Press the b utton -arrow -and pull the head
restraint o ut of the backrest "*.,& .
Installing the center head restraint
.. Slide the posts on the head restraint down
into the guides u ntil you feel the posts click
into place .
.. Press the b utton -arrow- and slide the head
r estraint all th e way down . You should not
be able to pull the head restraint out of the
backrest .
A WARNING
=
-On ly remove the rea r seat head restra int
when necessary in orde r to install a child
seat . Install the hea d restraint aga in im­
mediately once the child se at is removed.
Driving without head res train ts or with
head restraints that are not properly ad­
justed increases the r isk of serious or fa­
tal neck injury dramatica lly.
- The head restraints for the outer seats in
the second row must be folded up when
persons are being carr ied in the third row
seating* - danger of injury!
- Read and heed all WARNINGS
¢page 167
Armrest
The arm rest contains a storage comportment
and two cup holders .
Fig . 8 4 Arm rest betwee n driver's a nd pass enge r's seat
.,. Push on the release lever ¢ fig. 84 to open
the storage compartmen t.

80 Seats and storage
Luggage compartment
Expanding luggage compartment
To expand the luggage compartment, the
seatbacks can be folded forward separately or together .
Fig. 86 Release lever fo r outer seatback
Fig. 87 Release leve r for cente r seatback
Folding the s eatback forward
,. Pull the lever up c:> fig . 86. T he seatback piv­
ots forward.
,. Allow the sea tback to latch in the lower·
most position.
Raising the seatback
,. Pull the lever up c:> fig. 86 and raise the seat­
back u ntil it is securely latched
c:> & -
Folding cente r seatback down
,. Press the release button c:> fig. 87. The red
mark on the release lever is visible.
,. Tilt the seatback forward .
Raising center seatba ck
,. Raise the seatback until it is securely latch ·
ed
c:> & . It is securely latched when the red
mark on the release button is no longer visi·
ble . T
he center seatback can be folded forwa rd
separately . Using this loading option, long ob·
j ects (e.g. skis) can be carried in the interior.
A WARNING
--
- The backrest must always be secure ly
latched so that the safety belt of the cen·
ter seating position can wo rk p roperly to
help protect the occupant.
- The backrest must be securely latched in
position so that no items contained in
the luggage compa rtment can s lide fo r·
ward upon sudden braking.
- Always check whether the latch is fully
engaged by pulling the seatback for­
ward.
- On veh icles w ith third row seating*, the
ce nter seatback must be in the upr ight
po sition and secu rely lat ched when per­
son s are being carried in t he thir d row
seats -danger injury!
- Never allow safety belts to become dam·
age d by be ing ca ugh t in door or seat
hardwa re .
- Torn or frayed safety be lts ca n tear and
damaged be lt hardware can break in a
crash. Inspect the belts periodica lly .
Belts showing damage to webbing, bind­
ings, buck les, or retractors m ust be re·
p laced.
A WARNING
-
A lways read and heed WARNINGS c:> .&. in
Loading the luggage compartment on
page
170 .
(D Note
-When folding the backrest back into
place , make sure the safety belt does not
get caught, because it can be damaged.
A damaged belt can fail to provide safe
restraint .
- The heat ing wires in the rear window can
be damaged by abrasive objects on the
parcel shelf .

-So that stale air can escape from the ve­
hicle be sure not to cover the ventilation
s lot between the rear lid and the lug ­
gage compartment cover.
Protective liner
Dirty or wet objects can be transported under the cargo floor in a protective troy.
Fig . 92 Cargo f loo r: folded upr ight
Fig . 93 Removing the cargo floor
Setting up the cargo floor
• Open the rear lid.
•Setup cargo floor with the help of the han­
dle @¢
fig. 92 and adjust the outs ide
edges in the recesses @.
• Lay the items in the protect ive tray.
Folding the cargo floor up
• Open the rear lid.
• Fold the cargo floor up to the seatback with
the help of the handle @.
Removing the cargo floor, installing
• Open the rear lid.
• Fold the cargo floor up to the seatback with
the help of the handle @.
• To remove, pull the entire cargo floor out of
the gu ides -arrow- ~
fig. 93 in the direction
of the rear of the vehicle .
Seats and storage 83
• To install the cargo f loor, set the front of it
into the guides and push it in the direction
of the seatback until it engages.
You can also store sma ll items
under the car­
go f loor.
The storage room in the protect ive tray can be
enlarged by folding the cargo floor forwa rd or
removing it .
T he protect ive tray can be removed upward by
the grip.
On vehicles with
6 or 7 seats* the cargo floor
cannot be folded up, only raised . If the cargo
floor is removed, the hooks must be pushed into the guides under the third row seating
when the cargo floor is re-installed.
& WARNING ~
When the cargo floor is folded upright, the
items being transported must not exceed
the maximum cargo height, 2/3 of the car­
go floor space with the floor folded for­
ward, or a weight of about 33 lb. (15 kg).
{I) Tips
We recommend that you use a tie-down
strap to secure objects to the tie-down
eyelets on the right and left sides of the
vehicle.
Ski sack
App lies to vehicles: wit h ski sack
The ski sock allows a maximum of 4 pairs of
skis or 2 snowboards to be carried inside the vehicle.
Fig. 94 Securing t he ski sack at the center rear seat
be lt buck le

84 Seats and storage
Loading
.. Fold the center seatback fo rward ¢ page 80 .
.. Remove the sack from the luggage compart-
ment and unfold it .
.. Place the empty sack over the lowered seat­
back so that the end with the zip fastener is
in the luggage compartment.
.. Load objects from the luggage compart­
ment into the sk i sack ¢
&-
Securing
.. Insert the ski sack strap@¢ fig. 94 into the
center seat be lt buck le
@ .
.. Pull the securing strap tight by the free end
of the belt ©-
.. Vehicles with 6 seats*: The ski sack has two
straps with hooks on the underside . Hang
the hooks into the luggage compartment by
the rear fastening eyes and pull the secur ing
strap tight by the free end ©-
Storage
.. Release the securing strap for the sack .
.. Pull the sack to the rear over the folded
down seatback.
.. Raise the seatback unt il it is securely latch­
ed .
.. Fold up the empty sack .
.. Stow the ski sack in the luggage compart­
ment so that it cannot slide around.
A WARNING
-
-The ski sack is intended only for the
transportation of skis, snowboards and
other light objects. To reduce the risk of
serious persona l injury never transport
heavy or pointed objects in the ski sack.
- When brak ing rapidly or during an acci­
dent the load could be displaced and
cause injury to occupants.
- Sharp edges on the load must be covered
for protect ion. Always fasten the belt
tightly around the sack and its contents
¢fig. 94.
(D Tips
Never stow the ski sack away if it's wet or
damp (for examp le, snow me lting from
skis). Let it dry complete ly before you stow
i t away.
Roof rack
First things first
A roof rack can be fitted to carry additional
luggage on the roof.
.. Always read and follow the instructions pro ­
vided by the roof rack manufacturer when
installing the roof rack system .
If you are transporting luggage or other ob­
jects on the roof, please note the following :
- Your vehicle has spec ially designed aerody-
namic roof rails. Only install a roof rack spe­
cifically designed for your model. Contact
the nearest authorized Aud i dealer for infor­
mat ion on approved modula r roof racks for
your veh icle.
- These approved roof racks are the basis for a
complete roof rack system. Additional at­
tachments for the basic roof rack are neces­
sary to safely transport luggage, bicycles,
surf boards, skis or small boats. All necessa­
ry hardware for these systems is available at
your authorized Audi dealer.
- We recommend that you keep the installa­
tion instructions for your roof rack system
together with your Owner's literature in the
veh icle.
When should the roof rack be removed?
-Before going through an automatic car wash
(it is best to ask the car wash operator for
advice).
- When not in use, to reduce fuel consump­
tion, wind noise and to guard against theft.
A WARNING
-
- Use of an unapproved roof rack or incor-
rect mounting of an approved roof rack

86 Seats and storage
maneuvers when transporting cargo on
the roof of your vehicle.
- Never exceed the maximum permissible
load carrying capacity of the roof o f your
vehicle, the perm issib le axle weights and
the permiss ible total weight of your veh i­
cle
c:> page 313, Weights.
CD Note
Make sure that the opened rear lid does
not come in contact with the cargo on the
roof.
@) For the sake of the environment
As a resu lt of the increased wind resist­
ance created by a roof rack, your vehicle is
using fuel unnecessarily. So remove the
roof rack after using it .
Cupholder
Front cupholders
The cupholders ore located in the center arm­
rest.
Fig . 96 Ce nter a rmrest: Be verage holder
• Open the cover at the recess on the side
c:> fig . 96 .
A maxim um of two beverages can be accom­
modated in the cent er armrest . T he second
beverage holder is located under a cove r.
A WARNING
Spilled hot liquid can cause an accident
and personal injury .
-
-Never carry any beverage containers with
hot liquids, such as hot coffee or hot tea, in the vehicle while it is moving
. In case
of an acc ident, sudden braking or other
veh icle movement, hot liquid could spill,
causing scalding burns . Spilled hot liquid
can also cause an accident and personal
in ju ry .
- Use o nly soft cups in the cupholder . Hard
cups and glasses can cause injury in an
accident.
CD Note
Only drink conta iners with lids should be
carried in the cupholder. Liquid could spill
out and damage you r vehicle's electron ic
equipment or stain the upholstery, etc.
(upholder in the rear center armrest
The cupholder is located in the center con­
sole .
Fig. 97 R ea r cen te r a rmre st: c upho ld er ext ended
• To open the cupholder, press on the symbo l
'i c:>fig . 97 .
• To close the cupho lder, press the corrugated
area @ and fold the cover down.
The holder @adjusts to the beve rage holder .
The cupholder is designed to ho ld no more
than two cups or cans.
A WARNING
-
Spilled hot liqu id can cause an accident
and personal injury .
-
-Never carry any beverage conta iners with
hot liquids, such as hot coffee or hot tea,
in the vehicle while it is moving. In case
of an acc ident, sudden braking or other
veh icle movement, hot liquid could spill,

166 Driving Safely
• Always keep both feet in the footwell so
that you are in control of the vehicle at all
times.
For detailed information on how to adjust the
driver's seat, see
¢ page 73.
A WARNING
Drivers who are unbelted, out of position
or too close to the airbag can be seriously
injured by an airbag as it unfolds. To help
reduce the risk of serious personal injury:
- Always adjust the driver's seat and the
steering wheel so that there are at least
10 inches (25 cm) between your breast­
bone and the steering wheel.
- Always hold the steering wheel on the
outside of the steering wheel rim with
your hands at the 9 o'clock and 3 o'clock positions to help reduce the risk of per­
sonal injury if the driver's airbag inflates.
- Never hold the steering wheel at the
12 o'clock position or with your hands at
other positions inside the steering wheel
rim or on the steering wheel hub. Hold­
ing the steering wheel the wrong way
can cause serious injuries to the hands,
arms and head if the driver's airbag de­
ploys.
- Pointing the steering wheel toward your
face decreases the ability of the supple­
mental driver's airbag to protect you in a
collision.
- Always sit in an upright position and nev­
er lean against or place any part of your
body too close to the area where the air­
bags are located.
- Before driving, always adjust the front
seats and head restraints properly and
make sure that all passengers are prop­
erly restrained.
- Never adjust the seats while the vehicle
is moving . Your seat may move unexpect­
edly and you could lose control of the ve­
hicle.
- Never drive with the backrest reclined or
tilted far back! The farther the backrests
are tilted back, the greater the risk of in- jury due to incorrect positioning of the
safety belt and improper seating posi­
tion.
- Children must always ride in child safety
seats ¢
page 204. Special precautions
apply when installing a child safety seat
on the front passenger seat¢
page 183.
Proper seating position for the front
passenger
The proper front passenger seating position
is important for safe, relaxed driving .
For your own safety and to reduce the risk of
injury in the event of an accident, we recom ­
mend that you adjust the seat for the front
passenger to the following position :
• Adjust the angle of the seatback so that it is
in an upright position and your back comes
in full contact with it whenever the vehicle is
moving .
• Adjust the head restraint so the upper edge
is as even as possible with the top of your
head. If that is not possible, try to adjust
the head restraint so that it is as close to
this position as possible
¢ page 167.
• Keep both feet flat on the floor in front of
the front passenger seat .
• Fasten and wear safety belts correct­
ly ¢
page 178 .
For detailed information on how to adjust the
front passenger's seat, see ¢
page 72.
A WARNING
-Front seat passengers who are unbelted,
out of position or too close to the airbag
can be seriously injured or killed by the air­
bag as it unfolds. To help reduce the risk of
serious personal injury:
- Passengers must always sit in an upright
position and never lean against or place
any part of their body too close to the
area where the airbags are located.
- Passengers who are unbelted, out of po­
sition or too close to the airbag can be
seriously injured by an airbag as it