2013 MERCEDES-BENZ SL-CLASS ROADSTER display

i
You can only enter those cities, streets,
ZIP codes
etc. that are stored on the digital
map. This means that for some countries,
you cannot enter ZIP codes, for example.
The step-by-step instructions for entering an
address use the following example data:
New York (state)
New York (city)
40 Broadway
Of course, you can freely enter information
such as state/province, city, street and
house number, for example to enter your
home address.
Address entry menu
Calling up the address entry menu
X To switch to navigation mode: press the
Ø function button.
X To show the menu:
press W
the COMAND
controller.
X Select Dest. by

turning cVd the COMAND
controller and pressing W to confirm. Address entry menu
X
Select Address Entry and press W to
confirm.
The address entry menu appears. If you
have previously entered a destination, this
will be shown in the display.
Depending on the sequence in which you
enter the address and on the data status of
the digital

map, some menu items may not be
available at all or may not yet be available. Example: after you enter the state/province,
the Map, No., Center, Intersection, Save
and
Start menu

items are not available. The
ZIP code menu item is not available unless
the digital map contains ZIP codes.
Entering the state/province, city, street
and number
Selecting a state/province
X Call up the address entry menu
(Y page 299).
X Select State/Prov in the address entry
menu by turning cVd the COMAND
controller and press W to confirm.
A menu with the available lists appears:
R Last States/Provinces
R States (U.S.A.)
R Provinces (Canada)
X To select a list : turn cVd the COMAND
controller and press W to confirm.
The list of selected states/provinces
appears.
X To select a state/province: turn
cVd
the
COMAND controller and press W to
confirm.
The address entry menu appears again. The
state/province selected has now been
entered.
Entering a city
X Call up the address entry menu
(Y page 299).
X Select City in the address entry menu by
turning cVd the COMAND controller and
press W to confirm.
You will see the city list either with the
character bar (option 1) or as a selection
list (option 2). Navigation
299
COMAND Z

sliding
ZVÆ the COMAND controller and
press W to confirm.
You will
see the intersection list either with
the character bar (option 1) or as a
selection list (option 2). Intersection list with character bar
:
List entry most closely resembling the
characters entered so far
; List
= Character bar
Option 1: intersection list with character bar
X Enter an intersection. Character entry,
using city input as an example
(Y page 283). Intersection list as selection list
Option 2: intersection list as selection list
X
Select an intersection by turning cVd the
COMAND controller. X
Irrespective of the option, press W to
confirm your selection.
The address
entry menu appears again. The
intersection selected has been entered.
X Start route calculation (Y page 303).
Starting route calculation Address entry menu with destination address
:
Destination address
; To start route calculation
You can now have COMAND calculate the
route for the address specified or save the
address first, e.g. as your home address (My
Address) ( Y page 304).
X Call up the address entry menu
(Y page 299).
X In the address entry menu, confirm Start
by pressing W.
If no

other route has been calculated, route
calculation starts immediately (option 1). If
another route has already been calculated
(route guidance is active), a prompt
appears (option 2).
i The Continue menu item is displayed
instead of Start if Calculate
Alternative Routes is activated in the
navigation menu (option 2) ( Y page 327).
Option 1

– no route guidance active: route
calculation starts. While route calculation is
in progress, an arrow will indicate the
direction to your destination. Below this, you
will see a message, e.g. Calculating Fast
Route. Navigation
303
COMAND Z

Once the route has been calculated, route
guidance begins.
If the vehicle is not on a digitized road, the
following is displayed:
R
the linear distance to the destination
R the direction to the destination
R the Off Mapped Road message
Option 2 – route guidance is already
active: if route guidance is already active, a
prompt will appear asking whether you wish
to terminate the currently active route
guidance.
X Select Yes or No and press W to confirm.
If you select Yes, COMAND will stop route
guidance and
start route calculation for the
new destination.
If you select No, COMAND will continue
with the active route guidance.
i Route calculation

takes a certain amount
of time. The time depends on the distance
from the destination, for example.
COMAND calculates the route using the
digital map data.
The calculated route can differ from the
ideal route, for example because of
incomplete map data. Please also refer to
the notes about the digital map
(Y page 353).
Entering and saving your home address
You can either enter your home address for
the first time (option 1) or edit a previously
stored home address (option 2).
X Option 1: enter the address, e.g. a city,
street and house number ( Y page 299).
X Once you have entered the address, select
Save in

the address entry menu by turning
cVd and sliding ZVÆ the COMAND
controller and press W to confirm.
X Select Save as "My Address" and press
W to confirm.
COMAND stores

your home address under
the My Address entry in the destination
memory. X
Option 2: proceed as described under
"Option 1".
A prompt appears asking whether the
current home address should be
overwritten.
X Select Yes and press W to confirm.
After selecting Yes, the Saving
Procedure/Successful message
appears.
Selecting a destination from the
destination memory (e.g. home
address) Introduction
The destination memory always contains an
entry named "My Address". You may wish to
assign your home address to this entry, for
example
(Y

page 304), and select it for route
guidance. This entry is always located at the
top of the list in the destination memory.
X To switch to navigation mode: press the
Ø function button.
X To show the menu:
press W
the COMAND
controller.
X Select Destination in the navigation
system menu bar by turning cVd the
COMAND controller and pressing W to
confirm.
X Select From Memory and press W to
confirm.
You will see the destination memory list
either with the character bar (option 1) or
as a selection list ( option 2).304
Navigation
COMAND

Entering a destination using the map
Calling up the map
X
To switch to navigation mode: press the
Ø function button.
X To show the menu:
press W the COMAND
controller.
X Select Destination in the navigation
system menu bar by turning cVd the
COMAND controller and pressing W to
confirm. :
Current vehicle position
; Crosshair
= Details of the crosshair position
? Map scale selected
X Select Using Map

and press W to confirm.
You see the map with the crosshair.
Display = depends on the settings selected
in "Map information in the display"
(Y page 345). You can see the current street
name if the digital map contains the
necessary

data, You can see the coordinates
of the crosshair if the geo-coordinate display
is switched on and the GPS signal is strong
enough.
Moving the map and selecting the
destination
X To scroll the map: slide XVY, ZVÆ or
aVb the COMAND controller. X
To set the map scale: as
soon as you turn
cVd the COMAND controller, the scale bar
appears.
X Turn cVd until the desired scale is set.
Turning clockwise

zooms out from the map;
turning counter-clockwise zooms in. X
To select a destination: press W the
COMAND controller
once or several times.
If COMAND is unable to assign a unique
address, you will see either the address
entry menu with the destination address or
a selection list.
X Select a destination by turning cVd the
COMAND controller and press W to
confirm.
If the destination is within the limits of the
digital map, COMAND attempts to assign
the destination to the map.
If the

destination can be assigned, you will
see the address entry menu with the
address of the destination. If not, you will
see the Destination From Map entry.
X To start route calculation: select Start
and press W to confirm.
Entering a destination using geo-
coordinates X
To switch to navigation mode: press the
Ø function button.
X To show the menu: press W
the COMAND
controller.
X Select Destination in the navigation
system menu bar by turning cVd the306
Navigation
COMAND

X
To select a category: select a category by
turning cVd the COMAND controller and
press W to confirm.
COMAND first searches in the selected
category for destinations along the route.
If there are no destinations available there,
COMAND searches for destinations within
a radius of 60 miles(100 km) of the vehicle
position.
If COMAND finds destinations, a list
appears on the right-hand side of the
display.
The stopovers along the route are displayed
at the top of the list, sorted by increasing
distance from the vehicle's current position.
Below this, you will see the stopovers that
COMAND finds

in the vicinity of the vehicle's
current position.
i For stopovers that are not located along
the calculated route, the linear distance is
shown.
X Select a stopover by turning cVd the
COMAND controller and press W to
confirm.
The address entry menu appears, showing
the destination address.
X To start route calculation: select Start
and press W to confirm.
If COMAND does not find any destinations,
you will see a message to this effect.
X Confirm OK by pressing W.
X Select a different category.
Deleting a stopover
If a stopover has already been entered, you
can delete it.
X To switch to navigation mode: press the
Ø function button.
X To show the menu: press W
the COMAND
controller.
X Select Destination in the navigation
system menu bar by turning cVd theCOMAND controller and pressing
W to
confirm.
X Select Stopover and press W to confirm.
X Select Delete Stopover and press W to
confirm.
COMAND deletes the intermediate stop
and recalculates the route to the main
destination.
Entering waypoints Introduction
You can map the route yourself by entering
up to two waypoints. The sequence of the
waypoints can be changed at any time.
i
An intermediate stop is always between
the current position of the vehicle and the
first waypoint.
Creating waypoints
X To switch to navigation mode: press the
Ø function button.
X To show the menu:
press W
the COMAND
controller.
X Select Destination in the navigation
system menu bar by turning cVd the
COMAND controller and pressing W to
confirm. Waypoint menu without waypoints
X
Select Intermediate Destinations and
press W to confirm.
The destination is entered in the menu. 308
Navigation
COMAND

X
Confirm the symbol for waypoint 1 by
pressing W the COMAND controller. X
Confirm Set with the COMAND controller
W.
X Enter the waypoint via one of the following
options. Selection Action
Address Entry X
Enter a
destination by
address
(Y page 298). From Memory X
Select a
destination from
the destination
memory
(Y page 304). From Last
Destinations X
Select a
destination from
the list of last
destinations
(Y page 305). From POIs X
Select a point of
interest
(Y page 310). From Personal
POIs X
Enter a
destination from
the personal POIs
(Y page 319). Selection Action
Using Map X
Enter a
destination using
the map
(Y page 306). Using Geo-
Coordinates X
Enter a
destination using
the geo-
coordinates
(Y page 306). When the entry is complete, the waypoint
appears.
X
To accept the waypoint: confirm OK by
pressing W.
X To display the details: select
Details by
turning cVd the COMAND controller and
press W to confirm.
X To make a call: select Call with the
COMAND controller and press W to
confirm. COMAND switches to the
telephone function ( Y page 365).
i This menu

item is available if the waypoint
has a telephone number and if a mobile
phone is connected to COMAND
(Y page 359).
X To call up the map: select Map with the
COMAND controller and press W to
confirm.
X You can move the map and select the
destination. Navigation
309
COMAND Z

X
To store the waypoint in the destination
memory: select Presets with the
COMAND controller and press W to
confirm.
Once you
have accepted the waypoint, it is
entered in the waypoint menu. Waypoint menu with two waypoints
Editing waypoints
You can:
R
change waypoints
R change the

sequence in the waypoint menu
R delete waypoints
To change the sequence, both waypoints
must be entered.
X To change waypoints: select the symbol
for waypoint 1 or 2 in the waypoint menu
by turning cVd the COMAND controller
and press W to confirm.
X Select Edit and press W to confirm.
X Use one of the destination entry options
offered.
X To change the sequence of the
waypoints: select Swap in the waypoint
menu by turning cVd the COMAND
controller and press W to confirm.
The entries are swapped.
X To delete waypoints: select the symbol
for waypoint 1 or 2 in the waypoint menu
by turning cVd the COMAND controller
and press W to confirm.
X Select Delete and press W to confirm. i
You can use this menu item to delete a
waypoint directly after entry.
Accepting waypoints for the route X
Select Start in the waypoint menu by
turning cVd the COMAND controller and
press W to confirm.
The route is calculated with the entered
waypoints.
i The Continue menu item is displayed
instead of Start if Calculate
Alternative Routes is activated in the
navigation menu (option 2) ( Y page 327).
In the example, there are both waypoints 1
and 2. Entering a point of interest
Calling up the points of interest menu Example: POI menu
POIs are predefined destinations within
categories, e.g. a gas station in the
AUTOMOTIVE category.310
NavigationCOMAND

Searching by point of interest category
POI category list
X
Calling up the POI menu
After entering a city, the POI category list
appears after choosing the menu item
Near Destination, Current Position
or Other City.
X Select a POI category by turning cVd the
COMAND controller and press W to
confirm. The G arrow behind an entry
shows that other categories are available. GAS STATION category selected
X
Select an entry and press W to confirm.
The search for points of interest begins in
the vicinity of the selected position. Point of interest search near the current position
(example)
The example shows a search after selection
of the Rest Area entry.
i
The POI
search is canceled when 50 POIs
have been found.
COMAND performs a basic search in a
surrounding area of approximately
60 mi (100 km).
Once the search is completed, the POI list
is displayed.
If COMAND does not find any POIs within
the area, the search radius expands to
approximately 125 mi (200 km).
If COMAND finds one POI within this radius,
it finishes the search.
Point of interest list Introduction
Point of interest list (example)
The
POI

list displays the search results for the
category in the vicinity of the selected
position. Navigation
313
COMAND Z