2012 Peugeot 508 RXH Owner's Manual

8
183
!
Practical information

2. Infl ation
)Turn the selector A
to the "air" position.)Uncoil the black pipe Hfully. )Connect the black pipe to the
valve of the wheel.
) Connect the compressor's electric plug to
the vehicle's 12 V socket.) Star t the vehicle again and leave theengine running.
)
Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), in accordance with the vehicle's
tyre pressure label (located on the left hand
door aperture).
A loss of pressure indicates that thepuncture has not been fully plugged; contact a PEUGEOT dealer or qualified
workshop for assistance. ) Remove and stow the kit. )
Drive at reduced speed (50 mph [80 km/h]max) limiting the distance travelled to
approximatel
y 120 miles (200 km).
)Visit a PEUGEOT dealer or aqualified workshop as soon aspossible. You must inform the technician that you have used this kit. After
inspection, the technician willinform you whether the tyre can berepaired or must be replaced.

184
!
Practical information
Removing the cartridge
)Stow the black pipe.)Detach the angled base from the white pipe. )Suppor t the compressor ver tically.)Unscrew the car tridge from the bottom.



Beware of discharges of fluid.
The expiry date of the fluid is indicated on the car tridge.The sealant car tridge is designed for
single use; even if only partly used, itmust be replaced. After use, do not discard the car tridge into the environment, take it to anauthorised waste disposal site or aPEUGEOT dealer.
Do not forget to obtain a new sealantcartridge, available from PEUGEOT dealers or from a qualified workshop.



Checking tyre pressures/
inflatin
g accessories

You can also use the compressor, without injecting any product, to:


- check or adjust the pressure of your tyres,

- inflate other accessories (balls, bicycle
tyres...).
)
Turn the selector A
to the "Air"
position.
) Uncoil the black pipe H
fully.)
Connect the black pipe to the
valve of the wheel or accessory.
If necessary, fit one of the adaptorssupplied with the kit first.
)Connect the compressor's electrical connector to the vehicle's 12 V socket.)Star t the vehicle and let the engine run.)Adjust the pressure using the compressor (to inflate: switch B in position "I"
; to deflate: switch B
in position "O"and press button C), according to the vehicle's tyrepressure label or the accessory's pressure
label. )Remove the kit then stow it.

8
185
i !
Practical information










Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
The tools are located in the boot, behind the
r
ear seats.

Access to the tools
List of tools

All of these tools are specific to your vehicle andcan vary according to the level of equipment. Donot use them for other purposes.1.Wheelbrace. For removing the wheel trim and removing
the wheel bolts.
2. Jack with integral handle.
For raising the vehicle.
3."Bolt cover" tool.
For removing the bolt protectors
(covers)on alloy wheels.4.Socket for the security bolts (located in theglove box).
For adapting the wheelbrace to the special
"security" bolts.
5.One wheel chock for immobilising the
vehicle.
6. Towing eye.
See "Towing the vehicle".



Before doing any work on your vehicle,switch off the ignition (Ready
lamp off) to avoid any risk of injury resulting fromautomatic operation of the engine.
When using lifting equipment (a jackfor example), take care to use the
jacking points provided, so as to avoid damaging the high voltage cables.

186
ii
Practical information

Wheel with trim
When refitting the wheel
, refit the trimstarting by placing its notch facing thevalve and press around its edge withthe palm of your hand.

Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and not slippery. Apply the parking brake unless it has
been programmed to automatic mode, switch off the ignition and put the gear lever in position A
, M
or Rto block the wheels.Check that the braking warning lampand the P
warning lamp in the parkingbrake control lever come on. The occupants must get out of thevehicle and wait where they are safe.Never go underneath a vehicle raisedusing a jack; use an axle stand.


List of operations
)Remove the bolt cover from each of
the bolts using the tool 3 (according to equipment).)Fit the security socket 4on the
wheelbrace 1to slacken the security bolt(if fitted). )Slacken the other bolts using the
wheelbrace 1only.

8
187
Practical information
)Place the jack 2 in contact with one of thetwo front Aor rear B
locations provided on
the underbody, whichever is closest to the
wheel to be changed.

)
Raise the vehicle until there is sufficient space between the wheel and the ground
to admit the spare (not punctured) wheel easily.) Remove the bolts and store them in a clean place.
)
Remove the wheel.
)
Extend the jack 2
until its base plate is in contact with the ground. Ensure that the centreline of the jack base plate is directly below the location Aor B
used.

188
i
Practical information
Fitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. Have the tightening of the bolts and thepressure of the spare wheel checked
by a PEUGEOT dealer or a qualified workshop without delay. Have the punctured wheel repairedand refitted to the vehicle as soon as possible.


List of operations
)Put the wheel in place on the hub. )Screw in the bolts fully by hand.)Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 4 . )Pre-tighten the other bolts using the
wh
eelbrace 1only.

8
189
Practical information
)Lower the vehicle fully.)Fold the jack 2 and detach it.
)
Tighten the security bolt using the wheelbrace1fitted with the security socket 4.4)
Tighten the other bolts using the
wheelbrace 1 only.)
Refit the bolt covers on each of the bolts
(according to equipment). )
Store the tools in the box.

190
i
!
Practical information











Changing a bulb
Front lamps
Model with xenon and directional headlamps
1.Direction indicators (light emitting diodes - LEDs).2.Directional dipped/main beam
headlamps (D1S-35W).3.Daytime running lamps/sidelamps (light
emitting diodes - LEDs).
Model with halogen headlamps
1.Dipped and main beam headlamps (H7-55W).2.Main beam headlamps (H7-55W).3.Daytime running lamps/sidelamps (light
emitting diodes - LEDs).4.Direction indicators (PY21-21W).
For H7 type bulbs with lugs... take care toobserve their correct installation so as to ensure the best lighting performance.

In some weather conditions (e.g. lowtemperature or humidity), the presenceof misting on the internal sur face of the
glass of the headlamps and rear lamps is normal; it disappears after the lampshave been on for a few minutes.
Before doing any work on your vehicle,switch off the ignition ( Ready
lamp off)to avoid any risk of injury resulting fromautomatic operation of the engine.