2012 Peugeot 508 RXH Owner's Manual

5
143
!
Visibility
Foglamps selection ring
The foglamps operate with dipped and main beam headlamps.

Rear foglamps
When the headlamps switch off with automatic illumination of headlamps (AUTO model) or when the dipped beam headlamps are switched
off manually, the foglamps and sidelampsremain on.) Turn the ring rear wards to switch off thefoglamps, the sidelamps will then switch off.

In good or rainy weather, both day andnight, use of the the rear foglamps is prohibited. In these situations, thepower of their beams may dazzle other drivers. They should only be used in fog or snow.
In these weather conditions, it is your responsibility to switch on the foglamps and dipped headlamps manually as the sunshine sensor may detect sufficientlight.
Do not forget to switch off the rear foglamps when they are no longer needed.
)Turn the ring for wards and release toswitch on the rear foglamps.

144
i
i
i
Visibility

Lighting left on audible signal
An audible signal when a front door is opened warns the driver that the vehicle's exterior lighting is on, with the ignition off and in manual lighting mode.
In this case, switching off the lighting stops the audible signal.
With the ignition off, if the dippedheadlamps remain on, the vehicle goes into "ECO" mode to avoid dischargingthe battery.

In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal sur face of theglass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.

Daytime lighting, compulsory in cer tain
countries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other road users.
Daytime running lamps

This function is assured:


- in countries where it is imposed byregulations, by illumination of the dippedbeam headlamps with the sidelamps and number plate lamps.

- for other countries where it is provided, by
the use of dedicated lamps.

This function can be activated or deactivated via the vehicleconfiguration menu.



The lighting goes off when you switchoff the ignition, but you can always switch it on again using the lightingcontrol stalk.


*

f
unction that can be set in the vehicle
configuration menu.
LED lamps

They come on when the engine is started.
Depending on the destination country, they are used for:


- daytime running lamps *
in day mode andsidelamps in night mode (they are brighter
when daytime running lamps),
or


- sidelamps in day and night mode.
Where LED lamps are fitted, the filament bulbs
for the da
ytime running lamps/sidelamps in the front lamp units are not used.

5
145
Visibility
Parking lamps
Side markers for the vehicle by illumination of
the sidelamps on the traffic side only. ) Within one minute of switching off the
ignition, operate the lighting control stalk up
or down depending on the traffic side (for example: when parking on the left; lightingcontrol stalk upwards; the right handsidelamps are on).
This is confirmed by an audible signal andillumination of the corresponding direction indicator warning lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the middle position or
switch on the ignition.
Temporarily keeping the dipped beam
headlamps on after the ignition has beenswitched off makes the driver's exit easier when
the light is poor.
Manual guide-me-home
lighting

Switching on
)Within 30 seconds or a minute after switching of the ignition (according to theautomatic guide-me-home lighting durationprogrammed in the configuration menu),
"flash" the headlamps using the lightingstalk.)A further "headlamp flash" switches the
function off.



Switching off

The manual guide-me-home lighting switches
off automatically after about 30 seconds.

146
!
Visibility
The sidelamps and dipped beam headlamps are switched
on automaticall
y, without any action on the par t of the
driver, when a low level of external light is detected or in certain cases of activation of the windscreen wipers. As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
off, the lamps are switched off automaticall
y.
Automatic illumination of
headlam
ps
Activation
) Turn the ring to the "AUTO"
position. The automatic
illumination of headlamps is accompanied by a
message in the instrument panel screen.
Deactivation
)Turn the ring to another position. Deactivation is accompanied by a message in the instrument panel screen.


Association with automatic guide-me-home lighting

Association with automatic illumination of
headlamps provides the guide-me-home lighting with the following additional options:


- selection of the lighting duration of 15, 30or 60 seconds,

- automatic activation of guide-me-home lighting when the automatic illumination of
headlamps is in operation.



Operating fault

In the event of a fault with the sunshine sensor, the lightingcomes on, this warning lamp
is displayed in the instrument panel and/or
a message appears in the instrument panel screen, accompanied by an audible signal.
Contact a PEUGEOT dealer or a qualified
workshop.
In fog or snow, the sunshine sensor maydetect sufficient light. In this case, the lighting will not come on automatically. Do not cover the sunshine sensor,coupled with the rain sensor and located in the centre of the windscreenbehind the rear view mirror; theassociated functions would no longer be controlled.


Programming
Selection of the duration of the guide-me-home lighting is done
in the configuration menu vehicleparameters, in the instrument panel screen.

5
147
i
i
Visibility

Adaptive lighting


Switching on
The driver can take over at any time, if the circumstances dictate:
System which automatically changes betweendipped and main beam according to the driving conditions, using a sensor in the rear viewmirror.
The system is active from 15 mph (25 km/h)
and is deactivated below 9 mph (15 km / h).
)put the lighting control stalk on the "AUTO"
or "Dipped/main beam headlamps"
position,
Switching off
) or by dipping the headlamps manually using the lighting control stalk, whether
in the "AUTO" or "Dipped/main beam
headlamps" position.
Flashing the headlamps does notdeactivate the system.The state of the system is stored in memory when switching off the ignition. This automatic headlamp dipping system is a driving aid. The driver remains responsible for the vehicle'slighting and its correct use for theprevailing conditions of light, visibility and traffic.

The system may suffer interference or not work correctly:


- under conditions of poor visibility(for example, snowfall, heavy rainor thick fog, ...),

- if the windscreen is dir ty, misted or obscured (by a sticker, ...) in front of the sensor,

- if the vehicle is facing highly reflective signs.



The system is not able to detect:


- road users that do not have their own lighting, such as pedestrians,

- road users whose lighting is obscured, such as vehicles running behind a safety barrier (on amotorway, for example),

- road users at the top or bottom of a steep slope, on twisty roads, on crossroads.


)press this button, the
warning lamp goes off,
) press this button, the
warning lamp comes on.

148
Visibility





Exterior welcome
lighting
Remote switching on of the lighting makes your approach to the vehicle easier in poor light. It is activated according to the level of light detected
by the sunshine sensor.
Switching on
Switchin
g off
The exterior welcome lighting switches off automatically after a set time, when the ignition is switched on or on locking the vehicle.

Programming


The lighting duration is selected
via the instrument panel screen
configuration menu.
) Press the open padlock on the
remote control.
The dipped beam headlamps
and the sidelamps come on; your
vehicle is also unlocked.










Door mirror spotlamps


Switching on

The spotlamps come on:


- when you unlock the vehicle,

- when you remove the key from the ignition,

- when you open a door,

- when you use the remote control.



Switching off

They are timed to go off automatically. To m a k e
your approach to the vehicle easier,
these illuminate:


- the zones facing the driver’s and
passenger’s doors,

- the zones forward of the door mirrors andrearward of the front doors.

5
149
i
!
Visibility






Manual adjustment
of halogen
headlamps







Automatic adjustment of xenon headlamps

To avoid causing a nuisance to other road
users, the beams of the halogen headlamps should be adjusted according to the load in the
vehicle. 1 Driver .2
Driver + front passenger.3
Driver + front passenger + rear passengers. 4
5 people. 5
5 people + a load in the boot.6
Driver + a load in the boot.If a fault occurs
, this
warning lamp is displayedin the instrument panel, accompanied by an audible signal and a
message in the instrument panel screen.
The s
ystem then places your headlamps in the lowest position.
In order to avoid causing a nuisance to other road users, this system corrects the height of the
xenon headlamps beam automatically and when
stationary, in relation to the load in the vehicle.


If a fault occurs, do not touch the xenonbulbs. Contact a PEUGEOT dealer or aqualified workshop.

The initial setting is position "0".

150
i
Visibility
When the dipped or main beam headlamps are on, this function enables the light beams toprovide improved lighting of the side of the road
when cornering.
The use of this function, associated with the
xenon headlamps only, considerably improves
the quality of your lighting when cornering.








Main directional lighting
with directional lighting
without directional lighting


Programming


Operating fault

The function is activated or
deactivated via the configuration
menu (in the instrument panel screen).
When stationary or moving at very low speed or when reverse gear isengaged, the function is inactive.
The status of the function remains in the memory when the ignition is switched off. I
f a fault occurs, this warning lamp flashes in the instrument panel,
accompanied by a message in the
instrument panel screen.
Contact a PEUGEOT dealer or a qualified workshop.