2012 MITSUBISHI iMiEV Owners Manual

7-38 Vehicle care and maintenance
7
Front side-marker lights
N00915500161
1. Insert a flat blade screwdriver into the end of the light
nearer the rear of the body and pry gently to remove the
light.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.2. Remove the socket and bulb assembly together by turning
it counterclockwise.*: Front of the vehicle
*
BK0140800US.book 38 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-39
7
3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
NOTE
When installing the light assembly, push in the end facing
the front of the vehicle first.*: Front of the vehicle
BK0140800US.book 39 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-40 Vehicle care and maintenance
7
Front turn signal lights/Front fog lights (if so
equipped)/Daytime running lights
(if so equipped)
N00943400312
1. To create enough work space, turn the steering wheel all
the way in the same direction to the side you wish to
replace.
2. Remove the clip (A) and bolts (B), then lift the cover (C).3. Turn the socket counterclockwise to remove it.
D- Front turn signal light
E- Front fog light
F- Daytime running light
BK0140800US.book 40 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-41
7
4. Remove the bulb as follows.
[Front turn signal light]
Pull the bulb out of the socket.
[Front fog light and daytime running light]
While holding down the tab (F), pull out the bulb assem-
bly (G).5. To install the bulb, perform the removal steps in reverse.Front fog light
Daytime running light Front turn signal light
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen light bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the fog lights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0140800US.book 41 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-42 Vehicle care and maintenance
7
Rear combination lights
N00943700487
1. Open the liftgate.
(Refer to “Liftgate” on page 3-16.)
2. Remove the screws (A) that hold the light unit and remove
the light unit.3. Move the light unit toward the rear of the vehicle and
remove the pins (B) of the light unit from the vehicle.
BK0140800US.book 42 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-43
7
4. Turn the socket counterclockwise to remove it.NOTE
The tail and stop lights use LEDs rather than bulbs.
For repair and replacement, contact a certified i-MiEV
dealer.5. Pull the bulb out of the socket.
6. To install the bulb, perform the removal steps in reverse.C- Tail and stop light (LED) - cannot be replaced
D- Rear turn signal light
E- Back up light
BK0140800US.book 43 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-44 Vehicle care and maintenance
7
Rear side-marker lights
N00935400108
1. Remove the clips (A), then lift the cover (B).2. Turn the socket (C) counterclockwise to remove it.
3. Pull the bulb out of the socket.
BK0140800US.book 44 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-45
7
4. To install the bulb, perform the removal steps in reverse.
High-mounted stop light
N00943900115
1. Remove the mounting screws (A) and remove the light
unit.
BK0140800US.book 45 ページ ２０１１年９月２９日　木曜日　午後３時２８分