2012 Citroen C5 display
[x] Cancel search: displayPage 33 of 316
I
31
MONITORING
Return to the main instrument
panel screen display
Successive rotations of the left-hand
thumb wheel on the steering wheel
allow you to return to the main instru-
ment panel screen display (vehicle
speed), via the navigation informa-
tion screen, then the screen display-
ing only the total mileage and the trip
mileage (bottom of screen).
Display of navigation
information on instrument
panel screen
You can display navigation informa-
tion on the instrument panel screen
by rotating the left-hand thumb wheel
on the steering wheel.
Log of alerts
This function allows you to display
the log of alerts.
)
Press on button A
.
The following messages appear con-
secutively on the instrument panel
screen:
- Tyre pressure check.
- Service indicator reminder.
- Display of message alerts.
- Oil level check.
Page 34 of 316
I
32
MONITORING
Warning and indicator lamps
Visual indicators which inform the driver of the occurrence of a malfunction or
fault (warning lamp) or of the operation of a system (operation or deactivation
indicator lamp).
Warning lamp
is on
Cause
Action / Observations
STOP
fi xed, associated
with another
warning lamp. It is associated with a
punctured tyre or the engine
coolant temperature. Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
CITROËN dealer or a qualifi ed workshop.
Service
temporarily. A minor fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown in the screen, such as, for example:
- the closing of the doors, boot, rear
screen or bonnet,
- the remote control battery,
- the tyre pressures,
- saturation of the particle emission fi lter
(Diesel).
For any other faults, contact a CITROËN
dealer or a qualifi ed workshop.
fi xed. A major fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown in the screen and contact a
CITROËN dealer or a qualifi ed workshop.
When the ignition is switched on
Certain warning lamps come on for a few seconds when the ignition is switched on.
When the engine is started, these warning lamps should go off.
If they remain on, before moving off, refer to the information for the warning lamp
concerned.
Associated warnings
The illumination, fi xed or fl
ashing, of certain warning lamps may be accompa-
nied by an audible signal and a message in the screen.
Warning lamps
When the engine is running or the
vehicle is being driven, the illumina-
tion of one of the following warning
lamps indicates a malfunction or
fault which requires action on the
part of the driver.
The illumination of a warning lamp is
always accompanied by the display
of an additional message, to assist
you in identifying the fault.
If you encounter any problems, con-
tact a CITROËN dealer or a qualifi ed
workshop.
Page 41 of 316
I
39
MONITORING
Service indicator
This information is displayed for a
few seconds when the ignition is
switched on. It informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is due
is calculated from the last indicator
zero reset. It is determined by two
parameters:
- the distance travelled,
- the time elapsed since the last
service.
More than 2 000 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no
service information appears on the
instrument panel central screen.
Between 600 miles (1 000 km)
and 2 000 miles (3 000 km) remain
before the next service is due
For 7 seconds after the ignition is switched
on, the spanner symbolising the service
operations comes on. The instrument pan-
el central screen indicates the distance re-
maining before the next service is due.
Example:
1 900 miles remain before the
next service is due.
For 7 seconds after the ignition is switched
on, the central screen indicates:
Less than 600 miles (1 000 km)
remain before the next service is due
Example:
500 miles remain before
the next service is due.
For 7 seconds after the ignition is
switched on, the central screen in-
dicates:
Service overdue
For 7 seconds after the ignition is
switched on, the spanner fl ashes
to indicate that the service must be
carried out as soon as possible.
Example:
the service is overdue by
180 miles.
For 7 seconds after the ignition is switched
on, the central screen indicates:
The spanner remains on
in the
screen to indicate that a service
must be carried out soon.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
The spanner remains on
in the
screen to indicate that a service
should have been carried out.
Page 42 of 316
I
40
MONITORING
Service indicator zero reset
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:
)
switch off the ignition,
)
press and hold the trip distance
recorder zero reset button,
)
switch on the ignition; the dis-
tance recorder display begins a
countdown,
)
when the display indicates "=0"
,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.
Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 30 minutes.
Oil level correct
Oil level incorrect
This is indicated by the message
"Oil level incorrect".
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine.
Oil level gauge problem
This is indicated by the message "Oil
level measurement invalid". Contact
a CITROËN dealer or a qualifi ed
workshop.
Page 43 of 316
I
41
MONITORING
Engine oil temperature gauge
Under normal operating conditions,
the bars should be within section 1
.
In severe operating conditions, the
bars may extend into section 2
.
In this event, slow down, and if neces-
sary, stop the engine and check the
levels (see corresponding section).
Coolant temperature gauge
Under normal operating conditions,
the bars should be within section 1
.
In severe operating conditions, the
bars may extend into section 2
, the
engine coolant temperature warning
lamp A
and the STOP
warning lamp
come on, stop as soon as it is safe
to do so
. Switch off the ignition. The
cooling fan may continue to oper-
ate for a certain time
.
Contact a CITROËN dealer or a
qualifi ed workshop.
If the SERVICE
warning lamp comes
on, check the levels (see corre-
sponding chapter). On horizontal ground, illumination of
the fuel low warning lamp indicates
that you are at the reserve level.
An alert message is displayed in the
instrument panel.
Fuel gauge
Page 45 of 316
II
43
MULTIFUNCTION SCREENS
MONOCHROME SCREEN C
Main Menu
Press on the button A
to view the
Main Menu of the multifunction
screen. This menu gives you access
to the following functions:
Displays in the screen
Radio-CD
(see "Audio and Telematics"
section)
Bluetooth ®
system
(see "Audio and Telematics"
section)
Controls
Displays according to context:
- time
- date,
- ambient temperature with air
conditioning (the value displayed
fl ashes if there is a risk of ice),
- parking sensor information,
- audio functions
- alert messages,
- settings menus for the screen
and vehicle systems.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion.
Personalisation -
Configuration
This permits activation / deactivation of the:
- brightness and contrast of the
multifunction screen,
- date and time,
- units of the ambient temperature
displayed.
A.
Access to the "Main Menu"
B.
Cancel the operation or return to
the previous display
C.
Scroll through the screen menus
Confi rmation at the steering wheel
D.
Confi rmation at the audio system
control panel
Page 46 of 316
II
44
MULTIFUNCTION SCREENS
Adjusting the brightness
and contrast
)
Press on A
.
)
Use C
to select the "Brightness -
video adjustment" menu. Confi rm
with a press on C
on the steering
wheel or D
on the audio equip-
ment.
)
Select the confi guration of the
screen using C
. Confi rm with a
press on C
on the steering wheel
or D
on the audio equipment.
)
Select the brightness setting.
Confi rm with a press on C
on the
steering wheel or D
on the audio
equipment.
)
Select the inverse or normal dis-
play mode using C
then validate
with a press on C
on the steering
wheel or D
on the audio equip-
ment. To adjust the brightness
select "+" or "-" and save your
setting with a press on C
.
)
Confi rm with "OK"
in the screen.
Adjusting the date and
the time
)
Press on A
.
)
Use C
to select the"Date and
time" menu, then confi rm your
choice with a press on C
on the
steering wheel or D
on the audio
system.
)
Select the screen confi guration
using C
. Confi rm with a press
on C
on the steering wheel or D
on the audio system
)
Select the date and the time set-
tings, using B
. Confi rm with a
press on C
on the steering wheel
or D
on the audio system.
)
Press C
to select the values you
wish to modify. Confi rm your
choice with a press on C
on the
steering wheel or D
on the audio
system.
)
Confi rm with "OK"
on the screen.
Choosing the units
)
Press on A
.
)
Use C
to select the "Choice of
units" menu, then confi rm your
choice with a press on C
on the
steering wheel or D
on the audio
system.
)
Using C
, select the unit then val-
idate with a press on C
on the
steering wheel or D
on the audio
system.
)
Confi rm with "OK"
in the screen.
Selection of the type of
information displayed (Mode)
Successive presses on the end of
the wiper stalk or on the MODE
but-
ton on the audio equipment permit
selection of the type of informa-
tion presented in the multifunction
screen (date or radio, CD, MP3 CD,
CD changer).
Page 47 of 316
II
!
45
MULTIFUNCTION SCREENS
COLOUR SCREEN(WITH eMyWay)
Displays in the screen
Depending on the context, it displays:
- time,
- date,
- altitude,
- ambient temperature (the value
displayed fl ashes if there is a risk
of ice),
- parking sensor information,
- audio functions,
- telephone information and con-
tacts,
- satellite navigation system infor-
mation,
- alert messages,
- settings menus for the screen,
navigation system and vehicle
equipment.
Controls
From the eMyWay control panel, to
select one of the applications:
)
press the dedicated "RADIO"
,
"MUSIC"
, "NAV"
, "TRAFFIC"
,
"SETUP"
or "PHONE"
button
for access to the corresponding
menu,
)
turn dial A
to select a function,
an item in a list,
)
press button B
to confi rm the se-
lection,
or
)
press the "ESC"
button to aban-
don the current operation and re-
turn to the previous display.
For more information on these
applications, refer to the "Audio
Equipment" section.
"SETUP" menu
)
Press the "SETUP"
button to
gain access to the confi guration
settings menu:
- "Display confi guration",
- "Speech synthesis setting",
- "Select language",
- "Defi ne vehicle parameters",
- "Alert log".
For safety reasons, confi gu-
ration of the multifunction
screen by the driver must be only
done when stationary.