Page 8 of 316
6
FAMILIARISATION
The bonnet release should only be op-
erated when the vehicle is stationary.
)
Open the left hand front door.
)
Pull release lever A
to unlock the
bonnet.
Opening the bonnet
ACCESS
)
Lift safety catch B
, then raise the
bonnet.
Saloon
Tourer
Spare wheel
The tools are located in a protective
holder inside the spare wheel.
177
Access to the spare wheel
To access the spare wheel:
)
Saloon: raise the boot fl oor and fold
it in two.
)
Tourer: raise the boot fl oor and at-
tach it using the retractable grip.
Secure the hook to the upper part of
the boot.
)
To remove the spare wheel, detach
the strap then push the wheel for-
wards, before lifting it out.
Temporary puncture repair kit
The kit is a complete system comprised
of a compressor and a sealant car-
tridge.
174
162
Page 27 of 316
25
Limit the causes of excess
consumption
Spread loads throughout the vehicle;
place the heaviest items in the bottom
of the boot, as close as possible to the
rear seats.
Limit the loads carried in the vehicle
and reduce wind resistance (roof bars,
roof rack, bicycle carrier, trailer...). Use
a roof box in preference.
Remove roof bars and roof racks after
use.
At the end of winter, remove snow
tyres and refi t your summer tyres.
Observe the recommendations
on maintenance
Check the tyre pressures regularly,
when cold, referring to the label in the
door aperture, driver's side.
Carry out this check in particular:
- before a long journey,
- at each change of season,
- after a long period out of use.
Don't forget the spare wheel and the
tyres on any trailer or caravan.
Have your vehicle serviced regularly (en-
gine oil, oil fi lter, air fi lter...) and observe
the schedule of operations recommend-
ed by the manufacturer.
When refuelling, do not continue after
the 3 rd cut-off of the nozzle to avoid
any overfl ow.
At the wheel of your new vehicle,
it is only after the fi rst 1 800 miles
(3 000 kilometres) that you will see
the fuel consumption settle down to a
consistent average.
Page 103 of 316
VI
101
FITTINGS
BOOT FITTINGS (SALOON)
1.
Battery location for vehicles with
V6 HDi engine.
2.
Boot fl oor (spare wheel storage).
3.
Boot lamp.
4.
Location for 6 CD changer.
Luggage securing rings
)
Use the 4 securing rings on the
boot fl oor to secure your luggage.
For safety reasons in the event of
sharp braking, you are advised to
place heavy objects as far forward
in the boot as possible.
Page 118 of 316
VIII
116
SAFETY
Punctured tyre
automatic detection
detection on request
Automatic detection:
A message indicates which tyre is
punctured.
Driver request detection:
The vehicle outline indicates the
punctured tyre(s).
The message is accompanied by
illumination of the STOP
warning
lamp and an audible beep.
Wheel not monitored
automatic detection
detection on request
Automatic detection:
A message indicates to you which
wheel is not monitored.
Driver request detection:
The vehicle outline indicates the
wheel(s) which is/are not moni-
tored.
)
The message is accompanied by
illumination of the SERVICE
warn-
ing lamp and an audible beep.
have it checked by a CITROËN
dealer or a qualifi ed workshop. The defl ation detection system is a
driving aid, but which does not ab-
solve the driver from the need to be
vigilant and responsible.
This system does not dispense
with the requirement to check
the tyres on a regular basis (see
"Identifi cation markings") to ensure
optimum vehicle behaviour and to
avoid premature tyre wear under
certain conditions (high load, high
speed).
Do not forget to check the tyre
pressure of the spare wheel .
Any repair or replacement of a tyre
on a wheel that is equipped with
a sensor must be carried out by
a CITROËN dealer or a qualifi ed
workshop.
The system may suffer from tem-
porary interference caused by
electro-magnetic transmissions on
frequencies close to that use by
the system .
)
If you have fi tted wheels that
are not equipped with tyre defl a-
tion detection (wheels with snow
tyres, etc.), contact a CITROËN
dealer or a qualifi ed workshop.
Page 179 of 316
XI
177
PRACTICAL INFORMATION
CHANGING A WHEEL
Access to the tools
The tools are to be found in a protec-
tive holder inside the spare wheel.
)
Pull back the retaining strap for
access.
List of tools
All of these tools are specifi c to your
vehicle and may vary according to
equipment. Do not use them for any
other purpose.
1.
Wheelbrace
2.
Jack
3.
Tool for the removal/refi tting of bolt
protectors
4.
Towing eye
5.
Moveable chock
Page 180 of 316
XI
!
178
PRACTICAL INFORMATION
Access to the spare wheel
To remove the spare wheel
)
Saloon: raise the boot fl oor and
fold in two.
)
Tourer: raise the boot fl oor and
hook it using the retractable
handle. Secure the hook to the
top part of the boot.
)
Detach the strap then push the
wheel forwards so as to be able
to lift it.
To reposition the spare wheel
)
Position the spare wheel fl at in
the boot, then pull it towards you.
)
Next place the toolbox inside the
wheel, then secure the assembly
with the strap.
)
Release the boot fl oor to return it
to its initial position.
The tyre pressures are indi-
cated on the label located on
the driver's side centre door
pillar. Tyre pressures are given
for different vehicle loading condi-
tions.
Page 182 of 316
XI
!
180
PRACTICAL INFORMATION
Wheel for temporary use
Your vehicle may be fi tted with a
spare wheel which is different to
those on the vehicle. When fi tting
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
When refi tting the original wheel,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition.
Fitting a wheel
)
Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.
)
Screw in the bolts but do not fully
tighten them.
)
Lower the jack and remove it.
)
Tighten the wheel bolts, using
the wheelbrace.
)
Refi t the protectors on the bolts.
)
Return the ground clearance to
the normal position.
)
Ensure the tyre pressure is correct
and have the balancing checked.
Under-inflation detection
These wheels have tyre pressure
sensors. Repairs must be carried
out by a CITROËN dealer or a quali-
fi ed workshop.
Security bolts (according to
version)
Each wheel is equipped with one se-
curity bolt.
To remove it:
)
Remove the protector using tool 3
.
)
Use the security socket with the
wheelbrace.
If your vehicle is fi tted with a
spare wheel of a different size
to those on the vehicle, you
must not exceed 50 mph (80 km/h)
whilst using the spare wheel.
The wheel bolts are specifi c to the
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
or a qualifi ed workshop that the
wheel bolts are compatible with the
new wheels.
Take care to note down the code
number engraved on the head of
the security bolt socket. This will
enable you to obtain a replace-
ment security bolt socket from your
dealer.
Page 200 of 316
XI
!
198
PRACTICAL INFORMATION
ENERGY ECONOMYMODE
System which manages the duration
of use of certain functions to con-
serve a suffi cient level of charge in
the battery.
After the engine has stopped, you can
still use functions such as the audio
and telematics system, windscreen
wipers, dipped headlamps, courtesy
lights, etc. for a maximum combined
duration of thirty minutes.
This period may be signifi cantly re-
duced if the battery charge is low.
Exiting economy mode
These functions are reactivated auto-
matically next time the vehicle is driven.
)
In order to resume the use of
these functions immediately, start
the engine and let it run for a few
minutes.
The time available will then be dou-
ble the duration for which the en-
gine was left running. However, this
time will always be between fi ve and
thirty minutes.
A fl at battery prevents the en-
gine from starting (refer to the
corresponding section).
TOWING THE VEHICLE
Procedure for having your vehicle
towed or for towing another vehicle
using a removable towing eye.
Access to the tools
The towing eye is installed in the
jack box placed in the spare wheel.
For access to it:
)
open the boot,
)
raise the fl oor,
)
remove the towing eye from the
jack box.
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-function
screen indicating that the vehicle has
switched to economy mode and the
active functions are put on standby.
If the telephone is being used at this
time:
- it will be maintained for fi ve min-
utes with hands-free kit of your
Audio system,
- it will be maintained for ten minutes
with your eMyWay.
