2011 RENAULT SCENIC Engine And Peripherals EDC16C36 Workshop Manual

13B-425V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
END OF TEST 10.
TEST10
CONTINUED 9
Remove the plug welds from the fuel return pipe end pieces.
Connect the complete fuel return pipe to the injectors.
Wipe up any fuel run-off using a cleaning cloth (part number 77 11 211 707).
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-426V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST11 Diesel fuel conformity check
WARNING
During this operation, it is essential to:
– refrain from smoking or bringing incandescent objects close to the work area,
– protect yourself against fuel splashes due to residual pressure in the pipes,
– wear safety goggles with side guards,
– wear leaktight gloves (Nitrile type).
IMPORTANT
– To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
– To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Preparations:
Weigh an empty 1300 ml plastic cup (part no. 77 11 171 413) with its cover (part no. 77 11 171 416) using
electronic scales such as those used in body paint workshops (example: PANDA part no. 77 11 224 995). Record
the weight of the empty plastic cup.
This type of plastic cup is used to prepare paint.
Take a 1 l fuel sample from the diesel fuel filter outlet (see MR 364 (Mégane II ph2), Mechanical, 19C, Tank,
Fuel tank: Draining, or MR 370 (Scénic II ph2), Mechanical, 19C, Tank, Draining the fuel tank), using a
pneumatic transfer pump (part no. 634-200) and place it in the 1300 ml plastic cup.
Cover the plastic cup with its cover and let the fuel settle for approximately 2 minutes.
Is the fuel cloudy or does it
separate into two parts?Presence of water in diesel fuel, the fuel is not compliant.
Drain the fuel circuit, including the tank (see MR 364
(Mégane II ph2), Mechanical, 19C, Tank, Fuel tank:
Draining, or MR 370 (Scénic II ph2), Mechanical, 19C,
Tank, Draining the fuel tank).
YES
NO
EDC16C36_V44_TEST11/EDC16C36_V4C_TEST11/EDC16C36_V48_TEST11/EDC16C36_V50_TEST11/EDC16C36_V54_TEST11/
EDC16C36_V58_TEST11EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-427V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST11
CONTINUED 1
Weigh the diesel fuel and note the fuel weight after subtracting the weight of the empty plastic cup and its cover.
Does the fuel weight fall between the minimum and maximum weights given in the table below?
Calculated weight (g.)
Fuel temperature
(°C)
Min. weight Max. weight
821 846 13
821 846 14
820 845 15
819 844 16
819 844 17
818 843 18
817 842 19
816 841 20
816 841 21
815 840 22
814 839 23
814 839 24
813 838 25
Check the fuel temperature by immersing a thermometer in the plastic cup.
End of test. The fuel is not correct.
If the fuel weight is less than the minimum value then there is petrol in the diesel fuel.
If the fuel weight is greater than the maximum value then there is oil in the diesel fuel.
Drain the fuel circuit, including the tank (see MR 364 (Mégane II ph2), Mechanical,
19C, Tank, Fuel tank: Draining, or MR 370 (Scénic II ph2), Mechanical, 19C,
Tank, Draining the fuel tank).
YESNO
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-428V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST11
CONTINUED 2
Note:
If the weight measured reaches the limit values, the measurement can be performed with a 2230 ml plastic cup
(part no.77 11 171 414) and its cover (part no.77 11 171 417):
- Carry out a quick test drive in order to mix the fuel, then remove 2 l of fuel.
- Perform the test again and check the results by multiplying the limit values by 2.
Contact the Techline if you have doubts or problems with the customer.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-429V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST12 Manual clearing of weight of soot
Note: In certain cases, this procedure is to be carried out only after replacement of the particle filter or after an
After-sales regeneration of the particle filter.
– Start the engine.
– Raise the engine coolant temperature.
– Read the coolant temperature with the PR064 Coolant temperature until a value greater than 65ºC is obtained.
– Accelerate the engine to 4000 rpm and maintain this speed for 5 minutes.
–After 5 minutes, release the accelerator and stop the engine.
– Switch on the ignition.
– Run command SC036 Reinitialise programming and select After particle filter replacement or After particle
filter regeneration (as appropriate).
– Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
– Then switch on the ignition again and clear the present or stored faults from the computer memory (operation
to be carried out within 3 minutes of switching on the ignition).
EDC16C36_V44_TEST12/EDC16C36_V4C_TEST12/EDC16C36_V48_TEST12/EDC16C36_V50_TEST12/EDC16C36_V54_TEST12/
EDC16C36_V58_TEST12EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-430V9 MR-372-J84-13B450$210.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Injection computer128-track (BOSCH)
Connectors: black A 32-track, brown B 48-track, grey C 48-track
Atmospheric pressure sensorIntegrated into the computer (BOSCH)
Injector0.25 Ω at +20°C / 2 Ω max (BOSCH)
1600 bar (1800 bar max.)
Flow regulator (high pressure
pump)R = 3 ± 0.1 Ω at +20°C (BOSCH, CP3.2+ pump)
Rail pressure sensorRail pressure limiter: opening at around 1800 bar (BOSCH, bolted on rail)
Engine speed sensor R = 235 ± 35 Ω at + 23°C (MGI)
Camshaft sensorHall effect sensor (ELECTRICFIL)
R = 10250 ± 500 Ω at +20°C (measured between connections 3CQ and
3FB1 of the sensor)
Turbocharger control solenoid
valve15.4 ± 0.7 Ω at +20°C (PIERBURG)
Electric EGR valveConnection code 3VP: +12 V electric motor
Connection code 3GC: +5 V potentiometer
Connection code 3JM: potentiometer earth
Connection code 3VQ: motor earth
Connection code 3EL: potentiometer signal
DIRECT CURRENT MOTOR: R between connections 3VP and 3VQ = 1
Ω τo 400 Ω at +20°C
POTENTIOMETER: R between connections 3GC and 3JM: 3.9 kΩ < X <
9.1 kΩ at +20°C
(SIEMENS)
EGR by-pass solenoid valve 46 ± 3 W at +25°C (PIERBURG)
Electric damper valveDIRECT CURRENT MOTOR (VDO type)
Air flow sensorConnection code 3ABQ: air temperature signal
Connection code
3DW: flowmeter earth
Connection code 3KJ: +5 V flowmeter
Connection code 3FB2: +12 V battery
Connection code 3DV: air flow signal
Connection code 3DU: battery earth
(SIEMENS)
DIESEL INJECTION
Fault finding – Glossary

13B-431V9 MR-372-J84-13B450$210.mif
DIESEL INJECTION
Fault finding – Glossary13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
(R = Resistance)Air temperature sensorR = 3714 Ω ± 161 at + 10°C/
2448 Ω ± 96 at +20°C/
1671 Ω ± 59 at +30°C
Coolant temperature sensorConnection code3JK: Earth,
Connection code 3C: Signal (ELTH type)
R = 2252 Ω ± 112 at 25°C
811 Ω ± 39 at 50°C
283 Ω ± 8 at 80°C
Diesel fuel temperature sensorConnection code 3FAB: Signal,
Connection code 3LD: Earth (ELTH type)
R = 3820 Ω ± 282 Ω at +10°C/
2050 Ω ± 100 Ω at + 25°C/
810 Ω ± 47 Ω at +50°C
Accelerator pedal sensorR gang 1 = 1700 ± 900Ω
R gang 2 = 2850 ± 2050Ω
Heater plugR = 0.6 Ω at + 20°C / 2 Ω max
Max current drawn:
28 A at 0 s
12 A at 10 s
7 A after 30 s
Turbine upstream temperature
sensorConnection code 3ABT: Earth,
Connection code 3ABS: Signal (NTK type)
Particle filter differential pressure
sensorConnection code 3AAQ: 5 V,
Connection code 3TM: Earth,
Connection code 3TL: Signal
(BOSCH)
Temperature sensor upstream of
the particle filterConnection code 3TD: Signal,
Connection code 3XT: Earth (DENZO)
Temperature sensor downstream
of the particle filterConnection code 3TG: Signal,
Connection code 3XU: Earth (DENZO)
Water in diesel fuel sensorAccording to application (ZERTAN)