2011.5 Citroen DS5 HYBRID4 RHD Owner's Manual

233Checks
Opening the bonnet
Opening
)
From inside
: pull the release lever,located on the left below the dashboard,
towards you.
Before doing anything under the bonnet,
switch off the ignition (Ready lamp off) to avoid any risk of injury resulting fromautomatic operation of the engine.


Closing
)
Lower the bonnet and release it at the endof its travel. )
Check that it is latched correctly.


)From the outside: lift the safety catch and
raise the bonnet.
A bonnet strut opens the bonnet and holds itopen.


Never touch, handle or remove the orange "high voltage" cables.

The various caps and covers allow access for
checking the levels of the various fluids, for replacing cer tain components and for primingthe fuel system.














Diesel engine
1.
Power steering reservoir.2.
Screenwash and headlamp wash reser voir.3.
Coolant reservoir. 4.
Brake fluid reservoir.5.
Battery/Fuses.
6.Fusebox.
7. Air filter.8.Engine oil dipstick. 9.
Engine oil filler cap.10.Priming pump. 11.
Bleed screw. HDi 160 PEF 6- SPEED ELECTRONIC GEARBOX

235
Checks
On vehicle fitted with HDi engines, the fuel
system must be primed if you run out of fuel;
refer to the engine compar tment view on the
"Diesel engine" page.










Running out of fuel (Diesel)

If the tank on your vehicle is fitted witha misfuel prevention device, refer to thesection "Access - § Misfuel prevention (Diesel)".
)
Fill the fuel tank with at least five litres of Diesel.)
Open the bonnet. )
If necessary, unclip the style cover for
access to the priming pump.
) Slacken the bleed screw. )
Squeeze and release the priming pump
repeatedly until fuel appears in the
transparent pipe.
) Tighten the bleed screw.)
Operate the star ter until the engine star ts (if the engine fails to star t at the first
attempt, wait around 15 seconds before
trying again).) If the engine fails to star t after a few
attempts, operate the priming pump again,
th
en the starter.) Put the style cover back in position and clip it in place, ensuring that it has clippedcorrectly. )
Close the bonnet.

2 litre HDi engine


If the engine does not star t first time, don't keep trying. Star t the procedure
again from the beginning.

Before doing anything under the bonnet, switch off the ignition ( Readylamp off)to avoid any risk of injury resulting from automatic operation of the engine.

Checking levels Check all of these levels regularly and top them up if necessary, unless other wise indicated.
If a level drops significantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop.

When working under the bonnet, take care, as cer tain areas of the engine may be extremely hot (risk of burns).


Oil level

The reading will only be correct if the
vehicle is on level ground and theengine has been off for more than30 minutes.
The check is carried out either when the ignition
is switched on using the oil level indicator in the
instrument panel, or using the dipstick.

Engine oil change

Refer to the ser vicing booklet for the inter val for
this operation.
In order to maintain the reliabilit
y of the engine
and emission control system, the use of
additives in the engine oil is prohibited.


Oil specifi cation

The oil must correspond to your engineand conform to the manufacturer's
recommendations.
It is normal to top up the oil level between two services. CITROËNrecommends that you check the oil level, and top up if necessary, every3 000 miles (5 000 kilometres).
Before doing anything under the bonnet,switch off the ignition (Readylamp off) to avoid any risk of injury resulting from automatic operation of the engine.

237
Checks
Coolant level
The coolant level should be close
to the "MA X" mark but should never exceed it. When the engine is warm,
the temperature of the coolant is regulated bythe fan. This can operate with the ignition off.
On vehicles which are fitted with a par ticle
emission filter, the fan ma
y operate after
the vehicle has been switched off, even if
the en
gine is cold.

Changing the coolant
The coolant does not have to be changed.


Coolant specifi cation

The coolant must conform to the
manufacturer's recommendations.

Power steering fluid level
The power steering fluid level should
be close to the "MA X" mark. Unscrew
the cap, with the en
gine cold,
to check the level. Th
e brake fluid level should be closeto the "MA X" mark. If it is not, check
the brake pad wear.

Brake fluid level


Changing the fl uid

Refer to the ser vicing booklet for the inter val for
this operation.

Fluid specifi cation

The brake fluid must conform to themanufacturer's recommendations and meet
the DOT4 standard.
In addition, as the cooling system ispressurised, wait at least one hour after
switching off the engine before carrying out any work. To avoid any risk of scalding, unscrewthe cap by two turns to allow the pressure to drop. When the pressure has dropped, remove the cap and topup the level.

Screenwash / headlamp
wash fluid level
To check the level or top up the fluid on vehicle
fitted with headlamp washers, immobilise the
vehicle and switch of the en
gine. )Open the bonnet and secure it with
the stay. )Open the screenwash reser voir filler cap.

To p p i ng up

This additive must be topped up by a CITROËN
dealer or a qualified workshop without delay.

Diesel additive level
(Diesel engine with particle
emission filter)
A low additive level is
indicated by illumination of
the ser vice warning lamp,
accompanied by an audible
warning and a message in the instrument panelscreen.

Specifi cation of the fl uid
To ensure optimum cleaning and to avoid freezing, the fluid should never be topped up or
replaced by plain water.

)
Take and pinch the level gauge to block itsbreather.)
Remove the gauge completely from
the reservoir to read the level in thetransparent section.) To p u p i f n e c e s s a ry. )
Refit the filler cap to the reser voir and close the bonnet.