2010 Peugeot 407 Owner's Manual

5
78
Automatic rain sensitive
windscreen wipers
Activation REAR WIPER CONTROL (407 SW)
Deactivation
Do not cover the rain sensor
located on the windscreen be-
hind the rear view mirror.
When using an automatic car
wash to wash your vehicle, switch off
the ignition or check that the wiper
stalk is not in the automatic position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipers. Automatic rear wiper
If the windscreen wipers control is ac-
tivated and you engage reverse gear,
the rear wiper operates in intermittent
mode.

Note: if a bicycle carrier is
used, deactivate this function
by going to the "personalisa-
tion - confi guration" menu on
the multifunction screen or install a
special bicycle carrier approved by
PEUGEOT.
Turn the ring to the fi rst notch for inter-
mittent wiping.

The control must be reactivated if
the ignition has been switched off.
To do this, move the control to any
position then return it to the required
position.
Move the control to position
0 then re-
turn it to the AUTO position.
An indicator lamp comes on on the in-
strument panel screen, accompanied
by a message on the multifunction
screen.
In the AUTO position, the windscreen
wipers operate automatically and
adapt their speed to the intensity of
the rainfall.
Control with automatic wiping only
In the event of malfunction , the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Control with Intermittent and automatic wiping
Manual operation of the wiper stalk in-
terrupts the AUTO position, the deacti-
vation indicator lamp comes on on the
instrument panel screen, accompa-
nied by a message on the multifunc-
tion screen. Manual operation of the wiper stalk by
moving the stalk
A up and returning
it to position "0" interrupts the AUTO
position, the deactivation indicator
lamp comes on on the instrument pan-
el screen, accompanied by a message
on the multifunction screen.

5
79
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
windscreen wipers operate for a fi xed
period.
The headlamp wash is also activated,

if the headlamps are on .
When the minimum level of
the reservoir is reached, this
warning light comes on, ac-
companied by an audible
signal and a message on the
multi-function display.
Next time you stop, fi ll the screenwash/
headlamp wash reservoir.
The warning light comes on each time
the stalk is operated, until the reservoir
is fi lled. FRONT COURTESY LAMP
The courtesy lamp can be deactivated
by pressing switch 1 with the door open.
The map reading lamps are not affected
by this and may be switched on.

 To re-activate the lamps, press the
switch, with the door open.
Screenwash/headlamp wash low

1. Courtesy lamp

2. Map reading lamps
With the key in the ignition on or starting
position, operate the relevant switch.
The front courtesy lamp comes on
when the ignition key is removed, on
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or when the ve-
hicle is locked.

 Pressing switch 1 turns on the front
courtesy lamp.
Rear wash-wipe

Note: the rear wiper and rear
wash-wipe functions are de-
activated automatically when
the rear screen is opened.
Turn the ring beyond the fi rst notch,
the wash-wipe then the wiper operate
for a set period of time.

5
79
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
windscreen wipers operate for a fi xed
period.
The headlamp wash is also activated,

if the headlamps are on .
When the minimum level of
the reservoir is reached, this
warning light comes on, ac-
companied by an audible
signal and a message on the
multi-function display.
Next time you stop, fi ll the screenwash/
headlamp wash reservoir.
The warning light comes on each time
the stalk is operated, until the reservoir
is fi lled. FRONT COURTESY LAMP
The courtesy lamp can be deactivated
by pressing switch 1 with the door open.
The map reading lamps are not affected
by this and may be switched on.

 To re-activate the lamps, press the
switch, with the door open.
Screenwash/headlamp wash low

1. Courtesy lamp

2. Map reading lamps
With the key in the ignition on or starting
position, operate the relevant switch.
The front courtesy lamp comes on
when the ignition key is removed, on
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or when the ve-
hicle is locked.

 Pressing switch 1 turns on the front
courtesy lamp.
Rear wash-wipe

Note: the rear wiper and rear
wash-wipe functions are de-
activated automatically when
the rear screen is opened.
Turn the ring beyond the fi rst notch,
the wash-wipe then the wiper operate
for a set period of time.

5
80
REAR COURTESY LAMP (SALOON) REAR READING LAMPS (407 SW) Sill illumination
The sill lighting is at the bottom of each
door panel.
The lamps come on automatically
when a door is opened and switch off
automatically when all of the doors are
closed.
Boot light
The boot light is located in the right-
hand boot trim.
It comes on automatically when the
boot is opened and switches off auto-
matically when the boot is closed.

1. Courtesy lamp

2. Map reading lamps
With the key in the ignition on or start-
ing position, operate the relevant
switch.
The rear courtesy lamp comes on
when the ignition key is removed, on
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or the vehicle
is locked.

 Pressing switch 1 turns on the rear
courtesy lamp.
The courtesy lamp can be deactivated
by pressing switch 1 with the door open.
The map reading lamps are not affected
by this and may be switched on.

 To re-activate the lamps, press the
switch, with the door open. With the key in the ignition on or start-
ing position, press the corresponding
switch.
The rear reading lamps come on when
the key is removed from the ignition
and when the vehicle is unlocked.
They switch off gradually when the ig-
nition is switched on or when the ve-
hicle is locked.

 Pressing switch 1 switches on the
rear reading lamp concerned for
ten minutes.

6FITTINGS
81
INTERIOR FITTINGS
This is fi tted with a lock.
To open the glove box, lift the handle.
The glove box lights when the lid is
opened.
It is fi tted with three sockets for con-
necting video equipment (vehicle fi tted
with a 16/9 colour screen), a ventilation
nozzle that can be closed by means
of a dial, distributing conditioned air at
the same temperature as the vents of
the passenger compartment.
In cold weather, it is advisable to close
this nozzle to conserve the ambient air
inside the passenger compartment.
The glove box permits access to the
fascia fuse box. To open the compartment, lift the cover
or operate the lever on the left (accord-
ing to version).
The storage compartment permits ac-
cess to the USB socket and the storing
of CDs and coins.
Rear storage container
Closed storage compartment,
driver’s side
Door tray
This permits the storing of maps, tourist
guides or a bottle of water.
Front ashtray (100 W max)
This is fi tted with a lighter socket or
12 volt socket.
Press the cover to open the ashtray.
To empty the ashtray, after opening,
grip the receptacle and remove it. Retractable cup/can holder
This is located in front of the front armrest. Press the cover to open the cup/can
holder.
12 volt accessories socket (100 W max)
This is a lighter type socket, fi tted with
a cap. It is supplied with current from
the ignition on position.
This permits the storing of small ob-
jects such as keys, a parking badge or
a mobile telephone.
Air conditioned glove box Front armrest
This is located at the back of the front
armrest.
To empty it, open it fully, press the upper
tab then pull to remove it.

6FITTINGS
82
Rear armrest Fitting/Removing the mat
Storage compartments
There are two storage compartments
located in the boot side trim.
To gain access to a compartment:

 turn the two screws to the right and
remove the panel.
Access to the ski flap
To prevent the mat from becom-
ing caught under the pedals: - only use mats suited to the fi xings already present
in the vehicle. It is essen-
tial that these fi xings are
used.
- never fi t one mat on top of another.
The rear armrest consists of two com-
partments with a hinged cover.
Storage compartment
1 :

 Lift the cover. Pull the handle down then towards you
to open the fl ap.
When removing the mat on the driver's
side, push the seat as far back as pos-
sible and remove the fi xings.
When refi tting, position the mat correct-
ly on the pin and clip the fi xings. Check
that the mat is secured correctly.
Cup holder 2 :

 Fold the second cover forwards.

6FITTINGS
83
BOOT FITTINGS (407 SW)
3. Load space cover
To remove:

 Unclip the front ends and remove
the load space cover.
To install:

 Position the front ends of the load
space cover on its support and
press lightly to put it in place.
1. 12V accessories socket (100 W
max) and boot lamp
This is a cigar lighter type 12 volt sock-
et. It is installed on the rear left trim
and is supplied from the ignition on
position.
The boot lamp is controlled by opening
the tailgate or rear screen.
4. Stowing rings
There are four stowing rings on the
boot fl oor to which the luggage retain-
ing net can be attached.
2. Storage boxes
There are two side storage boxes
which can contain:
- on the left: a can of oil, a fi rst aid
kit, a puncture repair aerosol,
- on the right (except when a JBL Hi- Fi system is fi tted): a box of bulbs,
a warning triangle (support provi-
ded for this purpose), the luggage
retaining net.

6FITTINGS
84
High load retaining net
The high load retaining net can be
used behind the front seats (row 1) or
behind the rear bench seat (row 2).
To install it:

 fold the rear seat backs,

 position the high load retaining net
roller above the two rails 5 located
behind the rear seats (2/3 bench
seat). The two notches 6 must be
placed above the two rails,


slide the two rails 5 in the notches 6 ,

push the roller (in the direction of
the length) from right to left to se-
cure it,

 put the rear seat backs back in
place. To use it in
row 1 :

 fold the rear seat backs,

 open the covers 7 of the corre-
sponding upper fi xings,

 unroll the high load retaining net
and position one end of the metal
bar in the corresponding fi xing co-
ver. Ensure that the hook is seated
correctly in the rail located inside
the cover 7 ,

 pull the metal bar on the high load
retaining net to position the other
hook in the second fi xing cover.

Note : if it is used behind the
front seats, the rear seat backs
and cushions must be folded
(see section on rear seats).