2010 Peugeot 407 Owner's Manual

1010PRACTICAL INFORMATION
114
Fitting a wheel

 Position the wheel.

 Tighten the bolts by hand.

 Partly tighten the bolts using the
wheelbrace.

 Fold the jack 2 and remove it.

 Fully tighten the bolts using the
wheelbrace 1 .

 For vehicles with steel wheels, re-
fi t the wheel trim starting by plac-
ing its notch facing the valve and
press with the palm of the hand.

 For vehicles with alloy wheels, refi t
the covers.


Put the tool holder back in position.
This helps to keep the boot fl oor in its
correct position, to prevent any de-
formation of the fl oor when loaded.

 Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. Punctured tyre warning
lamp
Information on the instrument
panel:

Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the parking brake applied,
- with fi rst or reverse gear engaged (position P for the automatic gear-
box),
- never go underneath a vehicle which is supported only by a jack.
Tyre under-infl ation detection
system warning lamp
These original equipment wheels are
fi tted with a pressure sensor (see
paragraph "Tyre under-infl ation detec-
tion"). The warning which detects the
removal or absence of a wheel fi tted
with the pressure sensor signals the
anomaly. Have the wheel repaired and
checked by a PEUGEOT dealer.
After changing the wheel:
- have the tightness of the bolts and
the tyre pressure of the spare wheel
checked as soon as possible.
- have the punctured wheel repaired and refi t it to the vehicle as soon as
possible.
- have the spare wheel checked and replace it in its boot recess.
Recommendations when using
the temporary spare wheel *
Your vehicle may be equipped with a
spare wheel with a different rim to that
of the standard wheel.
After use, replace it as soon as possible.
Follow the recommendations below
to avoid any alteration in vehicle han-
dling:
-
do not drive above 50 mph (80 km/h) ,

- do not fi t a wheel trim,
- drive carefully,
- check the infl ation pressure indicated on the label.
* According to version and country.

1010PRACTICAL INFORMATION
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts. Fitting the spare wheel
If your vehicle is fi tted with a steel spare
wheel, when fi tting it, it is
normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
tial removable cover which is clipped
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
Once it has been fi tted on your vehicle,
it must be removed when the ambient
temperature rises above 10 °C again.
Consult a PEUGEOT dealer.
215/55 R17 tyres cannot be
fi tted with standard snow
chains, contact a PEUGEOT
dealer.
* According to country.
Special features of alloy
wheels
Security bolts
Your wheels are fi tted with security
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the security bolt
socket and the wheelbrace 1 .
Fitting snow tyres
If you fi t snow tyres mounted on steel
wheels onto your vehicle, it is
essen-
tial to use special bolts available from
your PEUGEOT dealer.
This security bolt socket was
given to you on delivery of
your vehicle with the duplicate
keys. Make a careful note of
the code number engraved on the
head of the security bolt socket. This
will enable you to obtain a duplicate
security bolt socket from a PEUGEOT
dealer. You are advised to do the same
for the duplicate keys.

1010PRACTICAL INFORMATION
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts. Fitting the spare wheel
If your vehicle is fi tted with a steel spare
wheel, when fi tting it, it is
normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
tial removable cover which is clipped
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
Once it has been fi tted on your vehicle,
it must be removed when the ambient
temperature rises above 10 °C again.
Consult a PEUGEOT dealer.
215/55 R17 tyres cannot be
fi tted with standard snow
chains, contact a PEUGEOT
dealer.
* According to country.
Special features of alloy
wheels
Security bolts
Your wheels are fi tted with security
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the security bolt
socket and the wheelbrace 1 .
Fitting snow tyres
If you fi t snow tyres mounted on steel
wheels onto your vehicle, it is
essen-
tial to use special bolts available from
your PEUGEOT dealer.
This security bolt socket was
given to you on delivery of
your vehicle with the duplicate
keys. Make a careful note of
the code number engraved on the
head of the security bolt socket. This
will enable you to obtain a duplicate
security bolt socket from a PEUGEOT
dealer. You are advised to do the same
for the duplicate keys.

1010PRACTICAL INFORMATION
116
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55W.

 Remove the protective cover cor-
responding to the faulty bulb.

 Disconnect the connector.

 Press the end of the securing clips
to free the bulb. Change the bulb.

 When fi tting the new bulb, ensure
that the direction notches are po-
sitioned correctly and the securing
clips are fi xed properly.

 Reconnect the connector.

 Refi t the protective cover.

4 - Direction indicators:
PY21W (amber).

 Turn the bulb holder a quarter turn
and remove it.

 Change the bulb.

WARNING: RISK OF ELEC-
TROCUTION
Front lamps
In the engine compartment, remove
the cover secured by one or two but-
terfl y screws, a plastic retainer clip and
two quarter turn screws.

1 - Dipped beam headlamps: H1-55W
or D2S-35W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direc-
tion indicators and side re-
peaters) must be replaced
with bulbs of identical specifi -
cation and colour.
5 - Front foglamps: H11 - 55W.
Turn the wheels to full lock.
Access to the bulb is via the fl ap in the
front mud fl ap.
Consult a PEUGEOT dealer.
The headlamps are fi tted with polycar-
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
Ensure that the liquid used to fi ll the
wash-wipe and headlamp wash reser-
voir is of good quality.

High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the other lamps and their surrounds
to avoid damaging their coating and
seals.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lighting is switched on.

3 - Sidelamps: W5W.

 Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.

 Put the connector back in place.

 Reconnect the connector.

 Refi t the protective cover.

1010PRACTICAL INFORMATION
117
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.

 Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.

 Press on the two tabs located at
the rear, near the rear screen.

 Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.

 Change the faulty bulb.

 When refi tting, ensure that the
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.

 Refi t the lamp fi xing nuts inside
the boot using the towing eye, if
necessary. When refi tting, ensure
that the lamp unit is positioned and
fi xed correctly.

 Reconnect the electrical connector.

Number plate lamps : W5W.

 Remove the transparent cover us-
ing a screwdriver blade.

 Change the faulty bulb.

 Push the repeater forwards or
backwards and release it.

 Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi cation and colour.
1. Direction indicators :
PY21W (amber).

2. Reversing lamps : P21W.

3. Foglamps/sidelamps :
P21/4W.

4. Sidelamps : P21/4W.

5. Brake lamps/sidelamps : P21/4W.

 Disconnect the electrical connector.

 Unscrew the lamp fi xing nuts in-
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.

 Remove the seal.

 Unclip the bulb holder moving
aside the 5 tabs.

 Unscrew the bulb and change it.

 Refi t the bulb holder.

 Reposition the seal.

1010PRACTICAL INFORMATION
117
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.

 Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.

 Press on the two tabs located at
the rear, near the rear screen.

 Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.

 Change the faulty bulb.

 When refi tting, ensure that the
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.

 Refi t the lamp fi xing nuts inside
the boot using the towing eye, if
necessary. When refi tting, ensure
that the lamp unit is positioned and
fi xed correctly.

 Reconnect the electrical connector.

Number plate lamps : W5W.

 Remove the transparent cover us-
ing a screwdriver blade.

 Change the faulty bulb.

 Push the repeater forwards or
backwards and release it.

 Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi cation and colour.
1. Direction indicators :
PY21W (amber).

2. Reversing lamps : P21W.

3. Foglamps/sidelamps :
P21/4W.

4. Sidelamps : P21/4W.

5. Brake lamps/sidelamps : P21/4W.

 Disconnect the electrical connector.

 Unscrew the lamp fi xing nuts in-
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.

 Remove the seal.

 Unclip the bulb holder moving
aside the 5 tabs.

 Unscrew the bulb and change it.

 Refi t the bulb holder.

 Reposition the seal.

1010PRACTICAL INFORMATION
118
CHANGING A REAR BULB (407SW)
Left and right foglamps: P21W.

 Carefully unclip the tailgate interior
trim.

 Detach the sealing fi lm located be-
hind the lamp in question.

 Remove the bulb holder turning it a
quarter of a turn.

 Change the faulty bulb.
When refi tting, ensure that the bulb is
positioned correctly in the bulb holder.

 Unclip the lamp (2 clips).

 Disconnect the connector and re-
move the lamp.

 Unclip the bulb holder moving
aside the 4 tabs.

 Unscrew the bulb and change it.

 Reconnect the connector.

 Refi t the bulb holder. When refi tting
it, ensure that the lamp is correctly
positioned and secured, reclipping
the rear part then the front part.

Number plate lamps: W5W.

 Insert a thin screwdriver in one of
the exterior holes of the transpar-
ent cover.


Push it towards the outside to unclip it.

 Remove the transparent cover.

 Change the faulty bulb. Third brake lamp (diodes)
All work on the diode lamps must be
carried out by a PEUGEOT dealer.
Wing lamps

1. Brake lamps/sidelamps: P21/5W.

2. Reversing lamps: P21W.

3. Direction indicators: P21W.
These three bulbs are changed by re-
moving the lamp.

 Remove the corresponding boot
side fl ap to gain access to the
lamp.

 Remove the lamp fi xing nut inside
the boot.
Note: if necessary, use the wheelbrace
to remove the nuts. In some climatic conditions
(e.g. low temperature or hu-
midity), the presence of misting
on the internal surface of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.

1010PRACTICAL INFORMATION
119
CHANGING A FUSE
The fuse boxes are placed in the lower
part of the fascia (passenger side in
the glove box) and in the engine com-
partment (left-hand side). Fascia fuses
To access the fuses, open the glove box. Open the fuse box co
ver by pressing the
two tabs at the top.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi ed. The fuse numbers are indicated
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Use the special pliers located
on the support next to the fuse box,
this support also contains the replace-
ment fuses.
Fuse N°
Rating

A
Functions

F1 15 Rear wiper.

F2 30 Central locking/deadlocking.

F3 5 Air bags.

F4 10 ESP dual function sensor, diagnostic connector,
sunroof (Saloon), steering wheel angle sensor.

F5 30 Front one-touch electric windows, sunroof
(Saloon), panoramic roof concealing fl ap
(407SW).

F6 30 Rear one-touch electric windows.

F7 5 Glove box lighting, side repeaters, front and rear
courtesy lamps, map reading lamps, courtesy
mirror.

F8 20 Multifunction display, audio equipment, steering
wheel control, trailer fuse box, alarm control unit,
navigation-telematics (according to country).