2010 Peugeot 407 change wheel
[x] Cancel search: change wheelPage 21 of 249
1
22
Battery charge warning
lamp
When the engine is running, this in-
dicates a charging circuit malfunction
(battery terminals, alternator belt).
Consult a PEUGEOT dealer. T y r e u n d e r - i n fl a t i o n w a r n i n g
lamp
This indicates that the tyre pressure is
too low.
A message on the multifunction screen
indicates the wheel(s) concerned.
R e f e r t o t h e i n f o r m a t i o n l a b e l a f fi x e d
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lamps Activation warning lamp
Operation warning lamp
Deactivation warning lamp
Malfunction warning lamp
Power steering warning
lamp
This indicates a power steering fault.
It is linked with the STOP warning
lamp.
Consult a PEUGEOT dealer. Parking brake warning lamp
This indicates that the parking brake is
still applied or has not been released
correctly.
It is linked with the braking system
warning lamp. Low screenwash and
h e a d l a m p w a s h fl u i d l e v e l
warning lamp
When the wipers are switched on, this
i n d i c a t e s t h a t t h e fl u i d l e v e l i s t o o l o w .
Fill the screenwash and headlamp
w a s h fl u i d r e s e r v o i r .
Engine oil level warning
lamp
This indicates that the engine oil level
is too low.
WARNING LAMPS IN THE INSTRUMENT PANEL SCREEN
These warning lamps are displayed
on the instrument panel screen.
STOP warning lamp
When this is displayed alone, it indi-
cates a power steering fault.
It comes on linked with the engine oil
pressure, coolant temperature, bra-
king system or punctured tyre warning
lamps.
Stop as soon as it is safe to do so.
Consult a PEUGEOT dealer.
Punctured tyre warning lamp
This indicates that one or more punc-
tured tyres have been detected.
A message on the multifunction screen
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
lamp.
Stop as soon as it is safe to do so.
Consult a PEUGEOT dealer.
Stop as soon as it is safe to do so.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Page 110 of 249
8DRIVING
94
PARKING BRAKE 6-SPEED MANUAL GEARBOX
To release
Pull the lever up and press the button
to release the parking brake.
To apply
When parking on a slope, turn the
wheels towards the kerb and apply the
parking brake.
Reverse
To change to reverse gear, lift the ring
under the gear lever knob and push
the gear lever to the left then to the
front.
Reverse gear can only be engaged
when the vehicle is stationary with
the engine idling.
Page 118 of 249
8DRIVING
102
TYRE UNDER-INFLATION DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction.
D e fl a t e d t y r e Instrument panel display warn-
ing lamp.
This is accompanied by the audible
signal and the message on the mul-
tifunction screen identifying the wheel
concerned.
If this warning lamp comes on, have
the tyre pressure checked as soon as
possible.
Puncture
This warning lamp, accompanied by
the audible signal and the message on
the multifunction screen identifying the
wheel concerned, is followed by illumi-
nation of the 'STOP' warning lamp. Stop as soon as it is safe to do so,
avoiding any sudden movement of the
steering wheel and the brakes.
Change the damaged wheel (punc-
t u r e d o r v e r y d e fl a t e d t y r e ) , a n d h a v e
the tyre pressure checked as soon as
possible.
Sensor(s) not detected or faulty
Instrument panel screen warn-
ing lamp. All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h t h i s
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install a
wheel which is not detected by your
vehicle, you must have the system re-
initialised by a PEUGEOT dealer.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem is an aid to driving which does not
replace the need for the driver to be
vigilant or to drive responsibly.
This system does not eliminate the
need to have the tyre pressures
checked regularly (see the label on
the door pillar) to ensure that the op-
timum dynamic performance of the
vehicle is maintained and prevent pre-
mature wear of the tyres, particularly
in arduous driving conditions (heavy
load, high speed).
The tyre pressures must be checked
cold, at least once a month. Remem-
ber to check the pressure of the spare
wheel.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem may experience temporary interfer-
ence due to electromagnetic emissions
on a frequency close to that used by the
system.
Note : this message is also
displayed when one of the
wheels is away from the ve-
hicle (being repaired) or when
one or more wheels without a sensor
a r e fi t t e d .
Instrument panel display warn-
ing lamp.
This is accompanied by the audible
signal and the message on the mul-
tifunction screen which indicates that
u n d e r - i n fl a t i o n d e t e c t i o n i s a b s e n t
from one (or several) wheel(s) or that
there is a fault in the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
Page 128 of 249
1010PRACTICAL INFORMATION
113
CHANGING A WHEEL
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:
1. Wheelbrace.
For removal of the wheel trim and removal of the wheel securing
bolts.
2. Jack with integral handle.
For raising the vehicle.
3. Removable towing eye.
See corresponding section.
4. Bolt cover tool.
For removal of the bolt protectors (covers) on alloy wheels. Removal
For vehicles with steel wheels, de-
tach the trim using the wheelbrace 1
pulling at the valve passage hole.
For vehicles with alloy wheels, re-
move the covers using tool 4 .
Loosen the wheel bolts.
Take the jack from the tool kit.
Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).
Extend the jack 2 until its base is in
contact with the ground.
Unscrew the bolts and remove the
wheel.
Access to the spare wheel and
the jack in the boot
L i f t t h e fl o o r u s i n g t h e g r i p . S e c u r e
the grip behind the boot seal. Never go underneath a ve-
hicle which is supported only
by a jack.
Park the vehicle on level, stable
and non-slippery ground.
Apply the parking brake, switch off
t h e i g n i t i o n a n d e n g a g e fi r s t o r r e -
verse gear (position P for the auto-
matic gearbox).
Page 129 of 249
1010PRACTICAL INFORMATION
114
Fitting a wheel
Position the wheel.
Tighten the bolts by hand.
Partly tighten the bolts using the
wheelbrace.
Fold the jack 2 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
For vehicles with steel wheels, re-
fi t t h e w h e e l t r i m s t a r t i n g b y p l a c -
ing its notch facing the valve and
press with the palm of the hand.
F o r v e h i c l e s w i t h a l l o y w h e e l s , r e fi t
the covers.
Put the tool holder back in position.
T h i s h e l p s t o k e e p t h e b o o t fl o o r i n i t s
correct position, to prevent any de-
f o r m a t i o n o f t h e fl o o r w h e n l o a d e d .
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. Punctured tyre warning
lamp
Information on the instrument
panel:
Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the parking brake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position P for the automatic gear-
box),
- never go underneath a vehicle which is supported only by a jack.
T y r e u n d e r - i n fl a t i o n d e t e c t i o n
system warning lamp
These original equipment wheels are
fi t t e d w i t h a p r e s s u r e s e n s o r ( s e e
p a r a g r a p h " T y r e u n d e r - i n fl a t i o n d e t e c -
tion"). The warning which detects the
r e m o v a l o r a b s e n c e o f a w h e e l fi t t e d
with the pressure sensor signals the
anomaly. Have the wheel repaired and
checked by a PEUGEOT dealer.
After changing the wheel:
- have the tightness of the bolts and
the tyre pressure of the spare wheel
checked as soon as possible.
- have the punctured wheel repaired a n d r e fi t i t t o t h e v e h i c l e a s s o o n a s
possible.
- have the spare wheel checked and replace it in its boot recess.
Recommendations when using
the temporary spare wheel *
Your vehicle may be equipped with a
spare wheel with a different rim to that
of the standard wheel.
After use, replace it as soon as possible.
Follow the recommendations below
to avoid any alteration in vehicle han-
dling:
-
do not drive above 50 mph (80 km/h) ,
- d o n o t fi t a w h e e l t r i m ,
- drive carefully,
- c h e c k t h e i n fl a t i o n p r e s s u r e i n d i c a t e d on the label.
* According to version and country.
Page 132 of 249
1010PRACTICAL INFORMATION
116
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55W.
Remove the protective cover cor-
responding to the faulty bulb.
Disconnect the connector.
Press the end of the securing clips
to free the bulb. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e
that the direction notches are po-
sitioned correctly and the securing
c l i p s a r e fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
4 - Direction indicators:
PY21W (amber).
Turn the bulb holder a quarter turn
and remove it.
Change the bulb.
WARNING: RISK OF ELEC-
TROCUTION
Front lamps
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam headlamps: H1-55W
or D2S-35W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direc-
tion indicators and side re-
peaters) must be replaced
w i t h b u l b s o f i d e n t i c a l s p e c i fi -
cation and colour.
5 - Front foglamps: H11 - 55W.
Turn the wheels to full lock.
A c c e s s t o t h e b u l b i s v i a t h e fl a p i n t h e
f r o n t m u d fl a p .
Consult a PEUGEOT dealer.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality.
High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the other lamps and their surrounds
to avoid damaging their coating and
seals.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lighting is switched on.
3 - Sidelamps: W5W.
Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.
Put the connector back in place.
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
Page 133 of 249
1010PRACTICAL INFORMATION
117
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.
Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.
Press on the two tabs located at
the rear, near the rear screen.
Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.
R e fi t t h e l a m p fi x i n g n u t s i n s i d e
the boot using the towing eye, if
n e c e s s a r y . W h e n r e fi t t i n g , e n s u r e
that the lamp unit is positioned and
fi x e d c o r r e c t l y .
Reconnect the electrical connector.
Number plate lamps : W5W.
Remove the transparent cover us-
ing a screwdriver blade.
Change the faulty bulb.
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi c a t i o n a n d c o l o u r .
1. Direction indicators :
PY21W (amber).
2. Reversing lamps : P21W.
3. Foglamps/sidelamps :
P21/4W.
4. Sidelamps : P21/4W.
5. Brake lamps/sidelamps : P21/4W.
Disconnect the electrical connector.
U n s c r e w t h e l a m p fi x i n g n u t s i n -
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
Remove the seal.
Unclip the bulb holder moving
aside the 5 tabs.
Unscrew the bulb and change it.
R e fi t t h e b u l b h o l d e r .
Reposition the seal.
Page 134 of 249
1010PRACTICAL INFORMATION
117
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.
Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.
Press on the two tabs located at
the rear, near the rear screen.
Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.
R e fi t t h e l a m p fi x i n g n u t s i n s i d e
the boot using the towing eye, if
n e c e s s a r y . W h e n r e fi t t i n g , e n s u r e
that the lamp unit is positioned and
fi x e d c o r r e c t l y .
Reconnect the electrical connector.
Number plate lamps : W5W.
Remove the transparent cover us-
ing a screwdriver blade.
Change the faulty bulb.
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi c a t i o n a n d c o l o u r .
1. Direction indicators :
PY21W (amber).
2. Reversing lamps : P21W.
3. Foglamps/sidelamps :
P21/4W.
4. Sidelamps : P21/4W.
5. Brake lamps/sidelamps : P21/4W.
Disconnect the electrical connector.
U n s c r e w t h e l a m p fi x i n g n u t s i n -
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
Remove the seal.
Unclip the bulb holder moving
aside the 5 tabs.
Unscrew the bulb and change it.
R e fi t t h e b u l b h o l d e r .
Reposition the seal.