2010 Peugeot 407 Owner's Manual

1
26
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule.
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
reset button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears .
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
ner fl ash.

Example : when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last ser- vice.
The distance remaining may be
weighted by the time factor, depen-
ding on the user's driving conditions.
Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example : when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.
After this operation, if you
wish to disconnect the battery,
lock the vehicle and wait for at
least fi ve minutes, otherwise
the zero re-set will not be
registered.

1
27
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information. Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil fi ller cap,
using the type of oil suited
to your engine.

A = max.

B = min.
Trip recorder zero reset
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
If the lack of oil is confi rmed by check-
ing with the dipstick, the level must be
topped up. Oil level indicator fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing indi-
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes. The total distance is displayed in
zone A of the display and the trip dis-
tance in zone B .
Distance recorder
With the trip distance displayed, press
the button for a few seconds.

1
28
TRIP COMPUTER

or
TRIP: access to the trip
computer displays.
Each successive press on the button
located at the end of the wiper stalk
displays different information.
LIGHTING RHEOSTAT
Zero reset
When the required trip is displayed,
press the control for more than
two seconds.
With the exterior lighting on, press the
button to vary the intensity of the ligh-
ting of the instruments and controls.
When the lighting reaches the mini-
mum (or maximum) setting, release
the button then press it again to in-
crease (or reduce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
- the "vehicle" tab with:

1
28
TRIP COMPUTER

or
TRIP: access to the trip
computer displays.
Each successive press on the button
located at the end of the wiper stalk
displays different information.
LIGHTING RHEOSTAT
Zero reset
When the required trip is displayed,
press the control for more than
two seconds.
With the exterior lighting on, press the
button to vary the intensity of the ligh-
ting of the instruments and controls.
When the lighting reaches the mini-
mum (or maximum) setting, release
the button then press it again to in-
crease (or reduce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
- the "vehicle" tab with:

1
29
Range (miles or km)
Current fuel consumption(l/100 or km/l or mpg)
This is the average quantity of fuel con-
sumed during the last few seconds.
This shows the distance that can still
be covered with the fuel remaining in
the tank in accordance with the ave-
rage consumption over the last few
miles (kilometres).
Distance remaining to be travelled (miles or km)
Average speed (mph or km/h)
TRIP menu
Press the
"MENU" button for access
to the main menu.
Select the "Trip computer" or "Ve-
hicle diagnostics" application using
the navigator, then confi rm or press
the "MODE" button until you gain ac-
cess to the trip computer screen, then
confi rm "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Alerts log,
- Status of the functions,
- Inputting the distance to be tra- velled.
Average fuel consumption(l/100 or km/l or mpg)
Distance travelled (miles or km)
Alerts log
This summarises the active warning
messages, displaying them on the
multifunction screen in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining (miles or km)
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled.
This fi gure may increase if
there is a change in the style
of driving or the road surface,
producing a signifi cant drop in
current fuel consumption.
When the range is less than 20 miles
(30 km), four bars are displayed. After
fi lling with fuel, the range is displayed
when it exceeds 62 miles (100 km).
If horizontal bars are displayed
for long periods instead of di-
gits, contact a dealer.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
This is the distance remaining to the
destination, either calculated at any
time by the navigation system if gui-
dance is activated or entered by the
user, minus the distance covered since
the distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to
zero.
This indicates the distance travelled
since the computer was last set to
zero.
Access via the main menu
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).

2MULTIFUNCTION SCREENS
30
MONOCHROME SCREEN C/COLOUR SCREEN C (WITH PEUGEOT CONNECT SOUND)
This displays the following information:
- time,
- date,
- ambient temperature (the value dis-played fl ashes if there is a risk of
ice),
- check of openings,
- vehicle function status messages, displayed temporarily,
- warning messages,
- audio functions,
- trip computer information,
- vehicle parameters,
- air conditioning settings,
- choice of language. Main menu
Defi ne the vehicle parameters
Permits the activation or deactivation
of certain driving and comfort elements.
Example: Automatic illumination of
headlamps.
Press the "MENU" button for access
to the main menu and select one of
the following functions: Audio Func-
tions, Trip Computer, Personalisation/
Confi guration and Air Conditioning.
Example: display selected on "Audio
Functions".
The "Personalisation-Confi guration"
menu provides access to successive
confi rmation windows.
Management of the displays
The "AUDIO" , "TRIP" and "CLIM"
buttons on the audio equipment key-
pad permit displaying in the main win-
dow (on the right).
Example: TRIP Choice of language
German, Spanish, French, English,
Italian, Dutch, Turkish, Portuguese
and Brazilian Portuguese.

2MULTIFUNCTION SCREENS
31
Display confi guration Changing the date and time Set the parameters one by one, using
the navigator, then confi rm by clicking
on "OK" .
From the list displayed, select "Display
confi guration" , then confi rm.
From the list displayed, select "Setting
the date and time" , then confi rm.
- Brightness, to be adjusted in accor-
dance with a scale between Moon
(-) and Sun (+).
- Selection of the units of measurement.
- Setting the date and time. Your op- erational zone is displayed on the
screen. Use the navigator to move
from one selection to another.
Your new parameters are confi rmed
one by one, by pressing the naviga-
tor button. All of the parameters are
recorded if you click on OK, displayed
on the screen.
The ESCape button on the control pad
enables you to choose not to confi rm
your changes.
- Selection of the colours (on colour screen C only). From the menu, displayed on the
screen, select the icon
"Personalisa-
tion-Confi guration" using the navi-
gator, then confi rm.
For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary.

2MULTIFUNCTION SCREENS
32
Display
This menu allows you to set the bright-
ness of the display, the display colour
scheme and the colour of the map
(day/night and auto mode).
Vehicle
This menu permits the activation or
deactivation of certain driving and
comfort systems:
- air conditioning (A/C),
- vehicle information,
- access to the vehicle,
- driving assistance,
- lighting confi guration,
- comfort lighting.
Units
This menu permits selection of the
units: temperature (°C or °F) and fuel
consumption (km/l, l/100, miles and
mpg).
System
This menu permits restoring of the factory
confi guration, display of the software ver-
sion and activation of scrolling text. For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary. COLOUR SCREEN (WITH PEUGEOT CONNECT NAVIGATION) "SETUP" menu
Press the SETUP button to gain access
to the "SETUP" menu. This provides
access to the following functions:
- System language,
- Date & Time,
- Display,
- Vehicle,
- Units,
- System.
System language
This menu allows you to select
the language used by the display:
German, English, Spanish, French,
Italian, Dutch, Polish, Portuguese.
Date & Time
This menu allows you to set the date
and time, the format of the date and
the format of the time (refer to the
"Audio and Telematics" section).
This displays the following information:
- time,
- date,
- ambient temperature (the value dis-
played fl ashes if there is a risk of ice),
- check of openings,
- vehicle function status messages, displayed temporarily,
- warning messages,
- audio functions,
- trip computer information,
- air conditioning settings,
- satellite navigation system information.