2010 Peugeot 206 P Dag ECO mode
[x] Cancel search: ECO modePage 50 of 107
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling
the various passenger compartment
lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds:
Page 55 of 107
i
61
The driver must ensure that passen-
gers use the seat belts correctly and
that they are all restrained securely
before setting off.
Wherever you are seated in the ve-
hicle, always fasten your seat belt,
even for short journeys.
Do not invert the seat belt buckles as
t h e y w i l l n o t f u l fi l t h e i r r o l e f u l l y .
T h e s e a t b e l t s a r e fi t t e d w i t h a n i n e r t i a
reel permitting automatic adjustment
of the length of the strap to your size.
The seat belt is stored automatically
when not in use.
Before and after use, ensure that the
seat belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in
the hollow of the shoulder.
T h e i n e r t i a r e e l s a r e fi t t e d w i t h a n a u -
tomatic locking device which comes
into operation in the event of a colli-
sion, emergency braking or if the ve-
hicle rolls over. You can release the
device by pulling rapidly on the strap
and releasing it. * According to model.
In order to be effective, a seat belt:
- must be tightened as close to the
body as possible,
- must restrain one person of adult size only,
- must not bear any trace of cuts or fraying,
- must be pulled in front of you with a smooth movement, checking
that it does not twist,
- must not be transformed or modi- fi e d t o a v o i d a l t e r i n g i t s p e r f o r m -
ance.
In accordance with current safety reg-
ulations, all repairs and checks must
be carried out by a PEUGEOT dealer
who guarantees that the work is car-
ried out correctly.
Have your seat belts checked regu-
larly by a PEUGEOT dealer and par-
ticularly if the straps show signs of
damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by PEUGEOT dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt is
positioned and is reeled in correctly. Recommendations for children
Use a suitable child seat if the pas-
senger is less than 12 years old or
s h o r t e r t h a n o n e m e t r e fi f t y .
Never use the same seat belt to
secure more than one person.
Never allow a child to travel on your
lap.
Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device * may be triggered
before and independently of the air-
bags. Triggering of the pre-tensioners
is accompanied by a slight discharge
of harmless smoke and a noise, due
to the activation of the pyrotechnic
cartridge incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked, and if neces-
sary replaced, by a PEUGEOT dealer.
Page 68 of 107
!
72
Programming
Turn dial 1 to the "LIMIT" position:
the speed limiter mode is selected
but is not switched on (OFF).
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed
speed will not have any effect unless you press the pedal
fi r m l y past the point of resistance .
The speed limiter is deactivated temporarily and the pro-
g r a m m e d s p e e d , w h i c h i s s t i l l d i s p l a y e d , fl a s h e s .
Returning to the programmed speed, by means of intentional
or unintentional deceleration of the vehicle, automaticall y
c a n c e l s t h e fl a s h i n g o f t h e p r o g r a m m e d s p e e d . Return to normal driving
Turn dial 1 to the "0" position: the
speed limiter mode is deselected.
The display returns to the distance
recorder.
You do not have to switch the speed
limiter on in order to set the speed.
Switch the speed limiter off by pressing button 4 : the
d i s p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( O F F ) .
Switch the speed limiter back on by pressing button 4
again.
Set the speed value by pressing button 2 or 3 (e.g.: 55 mph
(90 km/h)).
You can then change the programmed speed using but tons 2
and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
Switch the speed limiter on by pressing button 4 . Operating fault
In the event of a speed limiter malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have the system checked by a PEUGEOT
dealer.
On a steep descent or in the event
of sharp acceleration, the speed
limiter will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi-tioned correctly,
- d o n o t fi t o n e m a t o n t o p o f a n o - ther.
Page 88 of 107
!i
92
ECONOMY MODE FUNCTION
After the engine has stopped, with the
key in the accessories position, certain
functions (windscreen wiper, courtesy
lamps, audio equipment, dipped beam
headlamps, etc.) can only be used for
a maximum cumulative duration of ap-
p r o x i m a t e l y fi f t e e n m i n u t e s , t o p r e v e n t
discharging of the battery.
O n c e t h e fi f t e e n m i n u t e s a r e o v e r , t h e
message "Economy mode active" ap-
pears on the multifunction screen and
the active functions are put on standby.
These functions will be reactivated au-
tomatically the next time the vehicle is
used.
To resume the use of these functions
immediately, start the engine and let it
run for a few minutes.
The time available will then be double
the time for which the engine is left run-
ning. However, this time will always be
b e t w e e n fi v e a n d fi f t e e n m i n u t e s .
A fl a t b a t t e r y w i l l p r e v e n t t h e e n -
gine from starting.
TOWING THE VEHICLE
Procedure for having your vehicle towed.
Towing your vehicle
On the front bumper, unclip the cover
to gain access to the towing eye.
Switch on the hazard warning lamps
on the towed vehicle.
Place the gear lever in neutral. Towing another vehicle
Failure to comply with this special
requirement may result in damage
to certain braking components
and the absence of braking assis-
tance the next time the engine is
started.
Page 100 of 107
10
104
Button
Function
A Radio On/Off.
B - Decrease volume.
C + Increase volume.
D
CD eject.
E RDS * RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
F TA * T r a f fi c i n f o r m a t i o n p r i o r i t y o n / o f f .
Press for more than 2 seconds: PTY function on/off.
G
Setting of the bass, treble, loudness, sound distribution a
nd automatic volume correction.
H
Increase the setting of the functions associated with butto
n G .
I
Decrease the setting of the functions associated with butto
n G .
J
M a n u a l a n d a u t o m a t i c s e a r c h o f h i g h e r f r e q u e n c i e s .
Selection of the next track on the CD and of the PTY (radio).
K MAN Manual/automatic operation of buttons J and L .
L
M a n u a l a n d a u t o m a t i c s e a r c h o f l o w e r f r e q u e n c i e s .
Selection of the previous track on the CD and of the PTY (radi
o).
M CH. CD Selection of the CD changer source.
Press for more than 2 seconds: random play.
N CD Selection of the CD source.
Press for more than 2 seconds: random play.
O Radio Selection of the radio source. Selection of the FM1, FM2, FMAST
, AM wavebands.
Press for more than 2 seconds: automatic storing of stations (autosto re).
1 to 6 1 2 3 4 5 6 Selection of the stored station.
Press for more than 2 seconds: storing of a station.
* According to country.
Page 101 of 107
10
105
GENERAL FUNCTIONS
On/off
With the ignition key in
the accessories position
or with the ignition on,
press button A to switch
t h e a u d i o e q u i p m e n t o n
or off.
Anti-theft system
T h e a u d i o e q u i p m e n t i s c o d e d i n s u c h
a way that it can only operate in your
v e h i c l e . I t w o u l d n o t w o r k i f fi t t e d i n a n -
other vehicle.
The anti-theft system is automatic
and requires no action on your part.
Press button C to increase the audio
e q u i p m e n t v o l u m e o r b u t t o n B to de-
crease it.
A continuous press of buttons B and C
adjusts the volume gradually.
AUDIO SETTINGS
Press button G several
times in succession to
access the bass (BASS) ,
treble (TREB) , loudness
(LOUD) , fader (FAD) ,
balance (BAL) and auto-
matic volume correction
settings.
Exit from audio mode is automatic after
a few seconds without any action or by
pressing button G f o l l o w i n g c o n fi g u r a -
tion of the automatic volume correction. Adjusting the bass
When "BASS" is dis-
played, press button H or
I to change the setting.
- "BASS -9" for a min-
imum bass setting,
- "BASS 0" for a stan-
dard setting,
- "BASS +9" for a maximum bass
setting.
Adjusting the treble
When "TREB" is displayed, press but-
ton H or I to change the setting.
- "TREB -9" for a minimum treble set-
ting,
- "TREB 0" for a standard setting,
- "TREB +9" for a maximum treble
setting.
Adjusting the loudness (LOUD)
This function automatically emphasises
bass and treble tones.
Press button H or I to switch the func-
tion on or off.
Note: bass, treble and loudness settings
a r e s p e c i fi c t o e a c h s o u r c e . T h e y c a n b e
set differently for the radio or CD.
The audio equipment can operate for
30 minutes without the ignition being
switched on.
Page 105 of 107
10
108
RDS *
Using the RDS on FM
The RDS (Radio Data System) allows
you to continue listening to the same
s t a t i o n , w h a t e v e r f r e q u e n c y i t i s u s i n g
in the region you are travelling through. Press the "RDS" button
b r i e fl y t o s w i t c h t h e f u n c -
tion on or off.
The multifunction screen will indicate:
- "RDS" if the function is selected,
- "(RDS)" if the function is selected
but not available.
RDS station following
The display indicates the name of the sta-
tion selected. When the RDS is selected,
the radio searches continuously for the
transmitter which is broadcasting the se-
lected station with the best reception.
T r a f fi c i n f o r m a t i o n p r o g r a m m e ( T A ) Regional following mode (REG)
When they are part of a network, cer-
tain stations broadcast regional pro-
grammes in the various areas they
serve. The regional following mode
allows you to continue listening to the
same programme.
To do this, press the
"RDS" button for
more than two seconds to switch the
function on or off.
A n y t r a f fi c i n f o r m a t i o n a n n o u n c e m e n t
will be given priority, whatever source
you are listening to (radio, CD).
If you wish to interrupt a message,
press the
"TA" button; this switches the
function off.
N o t e : t h e v o l u m e o f t h e t r a f fi c i n f o r -
mation is independent of the volume
of normal radio listening. You can
adjust it using the volume button.
The setting will be stored and will be
used for subsequent messages.
Search by type of programme (PTY)
This allows you to listen to stations broad-
c a s t i n g a s p e c i fi c t y p e o f p r o g r a m m e
(News, Culture, Sport, Rock...). When FM is selected,
press the "TA" button for
more than two seconds
to switch the function on
or off. To search for a
PTY programme:
- select the PTY function,
- press button J or L b r i e fl y t o s c r o l l
down the list of the different types of
programme offered,
- when the programme of your choice is displayed, press button J or L for
more than two seconds to carry out
an automatic search (following an
automatic search, the PTY function
is switched off).
In PTY mode, the types of programme
can be stored. To do this, press the pre-
selection buttons "1" to "6" for more
than two seconds. Press the corre-
s p o n d i n g b u t t o n b r i e fl y t o r e c a l l t h e t y p e
of programme stored.
EON system
This system connects stations which
are part of the same network. It permits
the broadcasting of TA t r a f fi c i n f o r m a -
tion or of a PTY programme broadcast
by a station which is part of the same
network as the station to which you are
listening.
This service is available when you have
selected the TA t r a f fi c i n f o r m a t i o n p r o -
gramme or the PTY search by type of
programme.
Press the
"TA" button to
switch the function on or
off.
The multifunction screen will indicate:
- "TA" if the function is selected,
- "(TA)" if the function is selected but
not available.
* According to country.
Page 106 of 107
10
!
109
COMPACT DISC MODE
Selecting CD mode
Ejecting a disc Selecting a track
Press button
J to select the next track.
Press button L to return to the start of
the current track or to select the previ-
ous track.
Accelerated play
Press and hold button J or L for for-
wards or backwards accelerated play.
Accelerated play stops as soon as the
button is released. Random play (RDM)
When the CD player is selected, press
button
N for two seconds. The tracks
will be played in random order. Pressing
button N again for two seconds returns
you to normal play.
The random play mode is switched
o f f e a c h t i m e t h e a u d i o e q u i p m e n t i s
switched off.
The use of copied compact discs
may cause malfunctions.
Insert circular compact discs only.
Press button
D to eject
the disc from the player.
After inserting a disc,
printed face uppermost,
the player starts auto-
matically.
If the player already contains a disc,
press button N .