i
52
LIGHTING CONTROL STALK
System for selecting and controlling the
various front and rear lamps providing
the vehicle's lighting. Manual controls
Lighting off
Sidelamps
Dipped/Main beam head-
lamps
Lighting
The various front and rear lamps of the
vehicle are designed to improve the
driver's visibility depending on the exte-
rior conditions:
- sidelamps, to be seen,
- dipped beam headlamps, to see
without dazzling other drivers,
- main beam headlamps, for good visibility when the road is clear,
- rear foglamp, to be seen from a distance,
- front foglamps, for even better for- ward vision.
Programming
Various automatic lighting control
modes are also available according to
the following options:
- guide-me-home lighting,
- automatic illumination of headlamps. Selection is by turning ring
A .
Automatic illumination of
healamps Lighting on reminder
With the ignition off and the automatic illu-
mination of headlamps function switched
off, when the driver's door is opened,
a buzzer sounds if you have left the light-
ing on.
Front foglamps and rear
foglamp
Rotate the ring forwards to switch on
and backwards to switch off. The status
i s c o n fi r m e d b y t h e i n d i c a t o r l a m p o n
the instrument panel.
V e h i c l e s fi t t e d w i t h a r e a r
foglamp (ring B)
Dipped/Main beam change
Pull the stalk towards you. When the lighting is switched off
automatically, the rear foglamp
and the dipped headlamps re-
main on (turn the ring backwards
to switch off the rear foglamp.
The dipped beam headlamps and
sidelamps then switch off).
This only operates with the dipped/main
beam headlamps.
i
82
CHANGING A BULB
Front lamps
1. Direction indicators
(PY21W amber).
2. Sidelamps (W5W).
3. Dipped beam headlamps (H7-55W).
4. Main beam headlamps (H1-55W).
5. Foglamps (PSX-24W).
Operating procedure for replacing a
faulty bulb with a new bulb. These op-
erations must be carried out
with the
ignition off .
To gain access to the bulbs on the right-
hand side:
- Remove the screenwash reservoir fi l l e r t u b e .
- Unclip the engine harness 1 .
- Remove the nut from the engine management unit support 2 using a
size 10 spanner.
- Remove the engine management unit and support assembly. After changing the faulty bulb:
- Slide the two lugs of the engine
management unit support into the
locations A .
- Put the engine management unit back in place.
- Tighten the engine management unit support nut (size 10 spanner).
- Reclip the engine harness.
These bulbs are available from
PEUGEOT dealers.
In certain climatic conditions (low
temperature, humidity), conden-
sation inside the glass of the
headlamps and
other lamps
is
normal .
However, contact a PEUGEOT
dealer if water is present in the
headlamps.
89
or
Fuse N° Rating Functions
1 10 A Pre-heater unit (diesel) - Water in diesel sensor -
R e v e r s i n g l a m p s w i t c h - S p e e d s e n s o r - A i r fl o w
sensor (diesel)
2 15 A Canister electrovalve - Fuel pump
3 10 A ABS control unit
4 10 A Engine management unit
5 - Not used
6 15 A Front foglamps
7 - Not used
8 20 A Fan assembly relay - Engine management unit -
Diesel injection pump - Diesel high pressure
regulator - Engine management electrovalve
9 15 A Left-hand dipped beam
10 15 A Right-hand dipped beam 11 10 A Left-hand main beam
12 10 A Right-hand main beam
13 15 A Horn
14 10 A Front and rear windscreen wash pumps
15 30 A B u t t e r fl y h o u s i n g h e a t e r - D i e s e l i n j e c t i o n p u m p -
Oxygen sensor - Engine management unit - Air
fl o w s e n s o r - I g n i t i o n c o i l - E n g i n e m a n a g e m e n t
electrovalve - Diesel heater - Injectors
16 30 A Air pump relay
17 30 A High and low speed windscreen wiper
18 40 A Air conditioning fan
Engine compartment fuse box
To gain access to the box in the engine
compartment (next to the battery), un-
clip the cover.
A f t e r c a r r y i n g o u t w o r k , t a k e c a r e t o r e fi t
the cover correctly.
