2010 Peugeot 206 P Dag change wheel
[x] Cancel search: change wheelPage 36 of 107
i
4545
Steering lock
Before starting, unlock the steering, if
necessary, by turning the steering wheel
slightly while turning the key.
It is advisable to press the clutch pedal
whle operating the starter to facilitate
the starting of the engine. ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function cor-
rectly, the central locking button in-
dicator lamp, situated on the centre
c o n s o l e , fl a s h e s r a p i d l y w h e n t h e i g n i -
tion is switched on (2nd notch).
In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as
possible.
Key in ignition
If the key is left in the ignition, this
is indicated by an audible signal
when the driver's door is opened.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
press button A , the courtesy lamps
come on and the direction indicators
fl a s h f o r a f e w s e c o n d s . Changing the remote control
battery
Battery ref.: CR2016/3 volts.
I f t h e r e m o t e c o n t r o l b a t t e r y i s fl a t , y o u
are warned by a message on display B.
To replace the battery, remove the
screw then unclip the casing using a
coin at the ring.
If the remote control does not work after
the battery has been changed, repro-
gramme the remote control.
Reinitialising the remote control
Switch off the ignition.
Switch the ignition on again.
Press button A immediately for a
few seconds.
Switch off the ignition and remove
the remote control key from the igni-
tion lock. The remote control is now
working again.
Page 39 of 107
i
4545
Steering lock
Before starting, unlock the steering, if
necessary, by turning the steering wheel
slightly while turning the key.
It is advisable to press the clutch pedal
whle operating the starter to facilitate
the starting of the engine. ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function cor-
rectly, the central locking button in-
dicator lamp, situated on the centre
c o n s o l e , fl a s h e s r a p i d l y w h e n t h e i g n i -
tion is switched on (2nd notch).
In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as
possible.
Key in ignition
If the key is left in the ignition, this
is indicated by an audible signal
when the driver's door is opened.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
press button A , the courtesy lamps
come on and the direction indicators
fl a s h f o r a f e w s e c o n d s . Changing the remote control
battery
Battery ref.: CR2016/3 volts.
I f t h e r e m o t e c o n t r o l b a t t e r y i s fl a t , y o u
are warned by a message on display B.
To replace the battery, remove the
screw then unclip the casing using a
coin at the ring.
If the remote control does not work after
the battery has been changed, repro-
gramme the remote control.
Reinitialising the remote control
Switch off the ignition.
Switch the ignition on again.
Press button A immediately for a
few seconds.
Switch off the ignition and remove
the remote control key from the igni-
tion lock. The remote control is now
working again.
Page 51 of 107
i
57
DIRECTION INDICATORS
Lower the lighting stalk when mov-
ing to the left.
Raise the lighting stalk when mov-
ing to the right.
HAZARD WARNING LAMPS
Press this button, the direction indi-
c a t o r s fl a s h .
They can operate with the ignition off.
Automatic operation of hazard
warning lamps
When braking in an emergency, de-
pending on the deceleration, the hazard
warning lamps come on automatically.
T h e y s w i t c h o f f a u t o m a t i c a l l y t h e fi r s t
time you accelerate.
You can also switch them off by
pressing the button.
Press one of the spokes of the steer-
ing wheel.
Use the horn moderately and only
in the following cases:
- immediate danger,
- overtaking a cyclist or pedes- trian
- when approaching an area where there is no visibility.
Audible warning to alert other road users
to an imminent danger.
Selection of the left or right direction in-
dicators to signal a change of direction
of the vehicle. A visual warning by means of the direc-
tion indicators to alert other road users to
a vehicle breakdown, towing or accident.
Page 74 of 107
79
CHANGING A WHEEL
Operating procedure for replacing a
faulty wheel with the spare wheel using
the tools provided with the vehicle.
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery ground.
- Apply the parking brake, engage fi r s t o r r e v e r s e g e a r . Access to the spare wheel and
the jack
The wheel is located outside the ve-
hicle, under the boot, supported by a
metal carrier.
- Remove the wheelbrace
1 , secured
on the rear right inner panel of
the boot .
- Using the wheelbrace 1 , slacken the
spare wheel carrier retaining bolt,
located inside the boot under the
carpet .
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the jack storage case 2
located in the spare wheel. Removing a wheel
- Chock the rear of the wheel diagonally
opposite the wheel to be changed.
- Remove the wheel trim using the wheelbrace, by pulling at the valve
passage hole.
- Slacken the wheel bolts.
- Place the jack under the locating point on the sub-frame E that is
closest to the wheel to be changed.
Ensure that the entire surface of the
jack base plate is in contact with the
ground.
- Extend the jack, completely unscrew the bolts and remove the wheel.
Page 75 of 107
!
80
Fitting the wheel
- Once the wheel is in place, pre-tight-en it lightly using the wheelbrace.
- Fold the jack and remove it.
- Tighten the bolts using the wheel- brace.
- R e fi t t h e w h e e l t r i m s t a r t i n g a t t h e valve passage hole and press with
the palm of the hand. Putting the wheel back in place
- Put the jack storage case back in
the wheel.
- Put the wheel back in the carrier.
- Raise the wheel, then the carrier and reposition the hook.
- Do not forget to retighten the spare wheel carrier retaining bolt fully.
- Stow the wheelbrace. For your safety, always change a
wheel:
- on level, stable and non slip-
pery ground,
- with the parking brake applied, ignition off,
- w i t h fi r s t o r r e v e r s e g e a r e n - gaged,
- with the vehicle chocked,
- you must ensure that the oc- cupants get out of the vehicle
and wait in a safe location,
- never go underneath a vehicle raised using a jack (use an
axle stand).
The jack and all of the tools are
s p e c i fi c t o y o u r v e h i c l e . D o n o t
use them for other purposes.
After changing the wheel
- Have the tightening of the bolts and the pressure of the
spare tyre checked as soon
as possible by a PEUGEOT
dealer.
- Have the punctured tyre re- paired and replace it on the
vehicle as soon as possible.