2010 Peugeot 206 P Dag driver seat adjustment

54
AUTOMATIC ILLUMINATION OF
HEADLAMPS
The sidelamps and dipped beam head-
lamps switch on automatically if the light
is poor and when the windscreen wip-
ers operate continuously and switch off
when the light becomes bright enough
or the windscreen wipers are switched
off.
In foggy weather or in snow, the
brightness sensor may detect suffi -
cient light, the lighting will not come
on automatically. If necessary, the
dipped beam headlamps must be
switched on manually.
This function is active when the vehicle
is supplied to the customer.
To deactivate or activate the function:
- Place the key in the accessories po-sition (1st notch),
- Place the lighting stalk in the 0 posi-
tion,
- Press the end of the lighting stalk for more than four seconds.

Do not cover the brightness sensor,
coupled with the rain sensor, located
in the centre of the windscreen, be-
hind the
rear view
mirror. It is used
for
the
automatic
illumination
of

headlamps
. Operating check
Activation
Activation is accompanied by an audible
signal and a message on the multifunc-
tion screen.
Deactivation
Deactivation is accompanied by an au-
dible signal.
When the driver uses the manual light-
ing controls, the function is temporarily
deactivated.

If the brightness sensor does not
function correctly , the lighting come
on accompanied by an audible signal
and a message on the multifunction
screen.
Consult a PEUGEOT dealer.
HEADLAMP ADJUSTMENT
Depending on the load in your vehicle,
it is recommended that the headlamp
beam is adjusted.

0. 1 or 2 people in the front seats.

-. 3 people.

1. 5 people.

2. 5 people + maximum authorised
load.

3. Driver + maximum authorised load.

Initial setting is position 0.

60
SEAT BELTS
Driver's seat belt not
fastened/unfastened warning
lamp *
Front seat belt height adjustment
To lower the attachment point, pull the
control towards you and slide it down-
wards.
To raise the attachment point, slide the
control upwards. Fastening the seat belts
Pull the strap, then insert the tongue
into the buckle.
Check that the seat belt is fastened
correctly by pulling the strap.
Unfastening the seat belts
Press the red button on the buckle.
Front seat belts with pre-tensioner
and force limiter *
Safety in the event of front impacts has
been improved by the introduction of
seat belts with pre-tensioner and force
limiter for the front seats. Depending on
the seriousness of the impact, the pre-
tensioning system instantly tightens the
seat belts and pulls them against the
bodies of the occupants. Rear seat belts
The rear seats are fi tted with three-point
inertia reel seat belts.
The pre-tensioning seat belts are active
when the ignition is on.
The force limiter eases the pressure of
the seat belt against the chest of the oc-
cupant so increasing protection.
* According to model.
The warning lamp comes on each time
the ignition is switched on.
The warning lamp remains on until the
driver fastens their seat belt.
From 12 mph (20 km/h) and for two minu-
tes, the warning lamp fl ashes accom-
panied by an audible signal which
increases in volume and a message on
the multifunction screen.
Once these two minutes have elapsed,
the warning lamp remains on until the
driver fastens their seat belt.

i
61
The driver must ensure that passen-
gers use the seat belts correctly and
that they are all restrained securely
before setting off.
Wherever you are seated in the ve-
hicle, always fasten your seat belt,
even for short journeys.
Do not invert the seat belt buckles as
they will not fulfi l their role fully.
The seat belts are fi tted with an inertia
reel permitting automatic adjustment
of the length of the strap to your size.
The seat belt is stored automatically
when not in use.
Before and after use, ensure that the
seat belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in
the hollow of the shoulder.
The inertia reels are fi tted with an au-
tomatic locking device which comes
into operation in the event of a colli-
sion, emergency braking or if the ve-
hicle rolls over. You can release the
device by pulling rapidly on the strap
and releasing it. * According to model.
In order to be effective, a seat belt:
- must be tightened as close to the
body as possible,
- must restrain one person of adult size only,
- must not bear any trace of cuts or fraying,
- must be pulled in front of you with a smooth movement, checking
that it does not twist,
- must not be transformed or modi- fi ed to avoid altering its perform-
ance.
In accordance with current safety reg-
ulations, all repairs and checks must
be carried out by a PEUGEOT dealer
who guarantees that the work is car-
ried out correctly.
Have your seat belts checked regu-
larly by a PEUGEOT dealer and par-
ticularly if the straps show signs of
damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by PEUGEOT dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt is
positioned and is reeled in correctly. Recommendations for children
Use a suitable child seat if the pas-
senger is less than 12 years old or
shorter than one metre fi fty.
Never use the same seat belt to
secure more than one person.
Never allow a child to travel on your
lap.

Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device * may be triggered
before and independently of the air-
bags. Triggering of the pre-tensioners
is accompanied by a slight discharge
of harmless smoke and a noise, due
to the activation of the pyrotechnic
cartridge incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked, and if neces-
sary replaced, by a PEUGEOT dealer.