2010 JEEP GRAND CHEROKEE Owner handbook (in English)

•Or, disconnect the negative cable from the
battery.
• Anytime you store your vehicle, or keep it out
of service (i.e. vacation) for two weeks or
more, run the air conditioning system at idle
for about five minutes in the fresh air and
high blower setting. This will ensure ad-
equate system lubrication to minimize the
possibility of compressor damage when the
system is started again.
REPLACEMENT BULBS
Interior Lights Bulb Type
Glove Box Lamp ..............194
Grab Handle Lamp .......L002825W5W
Overhead Console
Reading Lamps ............. VT4976
Rear Cargo Lamp ............ 214–2
Visor Vanity Lamp ...........V26377
Underpanel Courtesy Lamps ........906
Instrument Cluster
(General Illumination) ............103
Telltale/Hazard Lamp .............74 Exterior Lights Bulb Type
Rear Turn Signal Lamps
. . 7440NA (WY21W)
Auxiliary Liftgate Tail Lamps .......W3W
Front Park/Turn Lamp ...........T20
Front Fog Lamps ........... PSX24W
Front Side Marker .............W5W
Headlamps (Low Beam) – High
Intensity Discharge (HID) .........D1S
(Serviced at Authorized Dealer)
Daytime Running Lamp (DRL) .....3157K
Headlamps (Low Beam) ..........H11
Headlamps (High Beam) .........9005
Liftgate Backup Lamps ......921(W16W)
Rear License Lamps ...........W5W
Rear Stop/Tail Lamps .....3157 (P27/7W)
Rear Fog Lamps .........7440 (W21W)
NOTE:
Numbers refer to commercial bulb types
that can be purchased from your authorized
dealer.
If a bulb needs to be replaced, visit your
authorized dealer or refer to the applicable
Service Manual.
BULB REPLACEMENT
High Intensity Discharge Headlamps
(HID) – If Equipped
The headlamps are a type of high voltage
discharge tube. High voltage can remain in the
circuit even with the headlamp switch off and
the key removed. Because of this, you should
not attempt to service a headlamp bulb your-
self. If a headlamp bulb fails, take your
vehicle to an authorized dealer for service.
WARNING!
A transient high tension occurs at the bulb
sockets of High Intensity Discharge (HID)
headlamps when the headlamp switch is
turned ON. It may cause serious electrical
shock or electrocution if not serviced properly.
See your authorized dealer for service.
NOTE:
On vehicles equipped with High Intensity
Discharge (HID) headlamps , when the head-
lamps are turned on, there is a blue hue to
the lamps. This diminishes and becomes
293

more white after approximately 10 seconds,
as the system charges.
Halogen Headlamps – If Equipped
1. Open the hood.
2. Turn the low or high beam bulb one–quarter
turn counterclockwise to remove from housing.
3. Disconnect the electrical connector and re-
place the bulb.
CAUTION!
Do not touch the new bulb with your fingers.
Oil contamination will severely shorten bulb
life. If the bulb comes in contact with any oily
surface, clean the bulb with rubbing alcohol.
Front Turn Signal
1. Open the hood.
2. Turn the turn signal bulb one–quarter turn
counterclockwise to remove from housing.
3. Disconnect the electrical connector and re-
place the bulb.
CAUTION!
Do not touch the new bulb with your fingers.
Oil contamination will severely shorten bulb
life. If the bulb comes in contact with any oily
surface, clean the bulb with rubbing alcohol.
Front Fog Lamps
1. Reach through the cutout in the splash
shield and disconnect the wiring harness from
the fog lamp connector.
2. Firmly grasp the bulb by the two latches and
squeeze them together to unlock the bulb from
the back of the front fog lamp housing.
3. Pull the bulb straight out from the keyed
opening in the housing.
CAUTION!
•Do not touch the new bulb with your fin-
gers. Oil contamination will severely
shorten bulb life. If the bulb comes in
contact with any oily surface, clean the bulb
with rubbing alcohol.
• Always use the correct bulb size and type
for replacement. An incorrect bulb size or
type may overheat and cause damage to
the lamp, the socket or the lamp wiring.
4. Align the index tabs of the front fog lamp
bulb with the slots in the collar of the bulb
opening on the back of the front fog lamp
housing.
5. Insert the bulb into the housing until the
index tabs are engaged in the slots of the collar.
6. Firmly and evenly push the bulb straight into
the lamp housing until both tabs snap firmly
into place and are fully engaged.
7. Connect the wiring harness to the front fog
lamp connector.
294

Rear Tail, Stop, and Turn Signal
Lamps
1. Raise the liftgate.
2. Remove the two push-pins from the tail lamp
housing.
3. Grasp the tail lamp and pull firmly rearward
to disengage the lamp from the aperture panel.
4. Twist socket counter clockwise and remove
from lamp.5. Pull the bulb to remove it from the socket.
6. Replace the bulb, reinstall the socket, and
reattach the lamp assembly.
Rear Liftgate Mounted Tail Lamp
1. Raise the liftgate.
2. Use a fiber stick or flat blade screw driver to
pry the lower trim from the liftgate.
3. Once lower trim is loose, close the liftgate.
4. Open the flipper glass.
5. Pull up glass seal at bottom of window
opening.
6. Remove small trim panel around liftgate
glass striker.
7. Close flipper glass and raise the liftgate.
8. Continue removing the trim.
9. Disconnect the two trim panel lights.
10. Tail lamps are now visible. Rotate socket(s)
counter clockwise.
11. Remove/replace bulb(s).
12. Reinstall the socket(s)
13. Reverse process to reinstall the liftgate
trim.
Rear Liftgate Tail Lamps
295

Rear Fascia Mounted Fog Lamp
1. Using a fiber stick or flat blade screw driver,
gently pry between the inboard edge of the
lamp and the fascia.
2. Remove lamp from fascia opening.
3. Twist socket counter clockwise.
4. Replace bulb.
5. Reinstall the socket.6. Hook inboard side of the lamp into the fascia
pocket.
7. Rotate lamp forward in car until lamp snaps
back into the opening.
Center High-Mounted Stop Lamp
(CHMSL)
The center high-mounted stop lamp is an LED
assembly. See your authorized dealer for re-
placement.
Rear License Lamp
1. Use a screw driver to gently pry against the
side of the snap tab to remove the license lamp
lens.
2. Pull bulb from socket.
3. Replace bulb.
4. Reinstall lens.
Rear Fog Lamps
Center High-Mounted Stop Lamp
296

FLUID CAPACITIES
U.S. Metric
Fuel (Approximate)
All Engines 24 Gallons 91 Liters
Engine Oil with Filter
3.6L Engine (SAE 5W-30, API Certified) 6 Quarts 5.6 Liters
5.7L Engine (SAE 5W-20, API Certified) 7 Quarts 6.6 Liters
3.0L Diesel Engine (SAE 5W-30 Synthetic, API Certified Low Ash) 10 Quarts 9.5 Liters
Cooling System *
3.6L Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula or
equivalent) 10.4 Quarts 9.9 Liters
5.7 Liter Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula
or equivalent) – Without Trailer Tow Package 15.4 Quarts 14.6 Liters
5.7 Liter Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula
or equivalent) – With Trailer Tow Package 16 Quarts 15.2 Liters
3.0L Diesel Engine (MOPAR Engine Coolant/Antifreeze 5-Year/100,000 Mile For-
mula or equivalent) 13.9 Quarts 13.2 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
297

FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine
Component Fluid, Lubricant, or Genuine Part
Engine Coolant MOPARAntifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technol-
ogy) or equivalent.
Engine Oil – Non ACEA Categories (3.6L En-
gine) Use API Certified SAE 5W-30 engine oil, meeting the requirements of Chrysler Material Standard
MS-6395. Refer to your engine oil filler cap for correct SAE grade.
Engine Oil – ACEA Categories (3.6L Engine) For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils meeting the requirements of ACEA C3, and approved to MB 229.31 or MB 229.51.
Engine Oil – Non ACEA Categories (5.7L En-
gine) Use API Certified SAE 5W-20 engine oil, meeting the requirements of Chrysler Material Standard
MS-6395. Refer to your engine oil filler cap for correct SAE grade. SAE 5W-30 engine oil ap-
proved to MB 229.31 or MB 229.51 may be used when SAE 5W-20 engine oil is not available.
Engine Oil – ACEA Categories (5.7L Engine) For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils meeting the requirements of ACEA C3, and approved to MB 229.31 or MB 229.51. SAE 5W-30
engine oil approved to MB 229.31 or MB 229.51 may be used when SAE 5W-20 engine oil is not
available.
Engine Oil – 3.0L Diesel Engine Use SAE 5W-30 Synthetic Low Ash Engine Oil, meeting the requirements of Chrysler Material Standard MS-11106 and approved to MB 229.31 or MB 229.51 and ACEA C3.
Engine Oil Filter MOPAR Engine Oil Filter or equivalent.
Spark Plugs – 3.6L Engine RER8ZWYCB4 (Gap 0.031 in [0.79 mm])
Spark Plugs – 5.7L Engine LZFR5C–11G (Gap 0.043 in [1.09 mm])
298

Component Fluid, Lubricant, or Genuine Part
Fuel Selection – 3.6L Engine 91 Octane
Fuel Selection – 5.7L Engine 91 Octane Acceptable - 95 Octane Recommended
Fuel Selection – 3.0L Diesel Engine Use good quality diesel fuel from a reputable supplier in your vehicle. The manufacturer requiresthat you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum)
and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid dam-
age to the emissions control system. For most year-round service, No. 2 diesel fuel meeting ASTM
specification D-975 Grade S15 will provide good performance. If the vehicle is exposed to extreme
cold (below 20F or -7C), or is required to operate at colder-than-normal conditions for prolonged
periods, use climatized No. 2 diesel fuel or dilute the No. 2 diesel fuel with 50% No. 1 diesel fuel.
This will provide better protection from fuel gelling or wax-plugging of the fuel filters. This vehicle is
fully compatible with biodiesel blends up to 5% biodiesel meeting ASTM specification D-975.
299

Chassis
Component Fluid, Lubricant, or Genuine Part
Automatic Transmission MOPARATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product.
Transfer Case MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product.
Axle Differential (Front-Rear) MOPAR Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction
modifier additive.
Axle Differential (Rear) – 5.7L Engine With Elec-
tronic Limited-Slip Differential (ELSD) MOPAR
Synthetic Gear & Axle Lubricant SAE 75W-90 (API-GL5) or equivalent.
Axle Differential (Rear) – 5.7L Engine Without
Electronic Limited-Slip Differential (ELSD) MOPAR
Synthetic Gear & Axle Lubricant SAE 75W-85 (API-GL5) or equivalent.
Brake Master Cylinder MOPAR DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not
available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
Power Steering Reservoir – 3.6L Engine and
3.0L Diesel Engine MOPAR
Hydraulic Fluid or equivalent meeting MS-1165, such as Fuchs EG ZH 3044 or Pentosin
CHF 11s.
Power Steering Reservoir – 5.7L Engine MOPAR Power Steering Fluid +4, MOPAR ATF+4 Automatic Transmission Fluid or equivalent
licensed ATF+4 product.
300
PAGE POSITION: 302 JOB:@ibm2/chry_pdm/CLS_chrysler-intl/GRP_owners/JOB_778130-en-grc/DIV_og-ee.\
en pubnum: NO-PUB-NUMBER